SY/T 5557-2001 Types and basic parameters of complete sets of petroleum cementing equipment
Some standard content:
ICS 75.180.10
Registration No.: 9598—2001
Petroleum and Natural Gas Industry Standard of the People's Republic of ChinaSY/T 5557—2001
Types and basic parameters of range equipmentforwell cementing
Published on 2001- 09-24
State Economic and Trade Commission
2002— 01— 01 Implementation
SY/T 5557-2001
Cited standards
Scope of complete equipment
Type and basic parameters of cementing manifold vehicle
Type and basic parameters of cementing instrument vehicle
Type and basic parameters of ash discharging vehicle
8Type and basic parameters of bulk cement tank
9Basic parameters of back-tank truck
10Type and basic parameters of bulk cement storage equipment.Type and basic parameters of cementing cement head
12Basic parameters of water supply truck-
SY/T 5557--2001
This standard is revised on the basis of SY/T5557-92 "Types and Basic Parameters of Complete Sets of Petroleum Cementing Equipment". The main revisions are as follows:
The structure, technical elements and expression rules of this standard are revised in accordance with GB/T1.1-1993; This standard has revised the name, scope, basic parameters and measurement units of complete sets of petroleum cementing equipment; This standard has added a high pressure grade of 105MPa and cement Basic parameters such as slurry density accuracy, flowmeter accuracy and pressure display value allowable error;
This standard adds GB/T9253.1-1999 and GB/T9253.2-1999 and other reference standards; This standard adds cementing cement head content; This standard deletes the two chapters "Complete set classification" and "Complete set basic parameters"; This standard removes the three items "Water bite", "Additive addition equipment" and "Air compressor unit"; This standard deletes the model representation method and Appendix A of petroleum cementing complete sets of equipment. From the date of implementation, this standard will replace SY/T5557-92 at the same time. This standard is proposed and managed by the National Technical Committee for Standardization of Petroleum Drilling and Production Equipment and Tools. Drafting units of this standard: Lanzhou Petroleum Machinery Research Institute, the Fourth Petroleum Machinery Factory of Jianghan Petroleum Administration Bureau, and Lanzhou General Machinery Factory. Drafters of this standard Gao Xiang and Yao Min
This standard was first issued in February 1993, and this is the first revision. 1 Scope
Petroleum and Natural Gas Industry Standard of the People's Republic of China Types and basic parameters of range equipmentfor well cementing
This standard specifies the scope, type, basic parameters and connection dimensions of petroleum cementing equipment. SY/T 5557—2001
Replaces SY/T5557--92
This standard applies to the design, manufacture and selection of onshore petroleum cementing equipment, and also applies to offshore cementing equipment. 2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. The parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T9253.1—1999 Threads for oil drill pipe joints GB/T9253.2—1999 T-marking, measurement and inspection of threads for casing, oil pipe and pipeline in the petroleum and natural gas industry GB/T 5796.1--1986 Trapezoidal thread profile GH/T5796.2-1986 Trapezoidal thread diameter and pitch series GB/T5796.3-1986 Trapezoidal thread basic dimensions GB/T5796.4--1986 Trapezoidal thread tolerance SY/T5211-93 High-pressure pipe connections and high-pressure flexible elbows 3 Scope of complete sets of equipment
The scope of complete sets of equipment includes:
a) Cementing truck (skid);
b) Cementing manifold truck:
c) Cementing instrument truck;
d) Cementing truck:
e) Bulk cement;
f) Tank truck;
g) Bulk cement storage equipment;
h) Cementing head;
) Water supply truck.
4 Cementing truck (according to) type and basic parameters 4.1 Type
4.1.1 According to the mode of transportation, it is divided into:
a) Truck-mounted;
b) Skid-mounted.
4.1.2 According to the transmission mode, it is divided into:
Approved by the State Economic and Trade Commission on September 24, 2001 and implemented on January 1, 2002
a) Hydraulic mechanical transmission;
b) Mechanical transmission.
4.1.3 According to the pump type, it is divided into:
a) Three-cylinder single-acting horizontal piston pump;
b) Double-cylinder double-acting pump.
4.1.4 According to the pump installation mode, it is divided into:
a) Single machine single pump;
b) Double machines double pumps;
|) Single machine double pumps.
4.1.5 According to the mixing method, it can be divided into
a) compound circulation type;
b) reflux type;
c) hydraulic jet type.
4.2 Basic parameters (see Table 1)
Basic parameter name
Maximum working pressure
Maximum displacement
Relative density of cement slurry
Accuracy of cement slurry density
Nominal diameter of pump discharge pipeline
Nominal diameter of pump suction pipeline
Note: (40) is a temporarily reserved parameter
Type and basic parameters of cementing manifold
5.1 Type
SY/T5557—2001
Table 1 Basic parameters of cementing truck (skid)
mr/min
Cementing manifold trucks are divided into the following categories according to their transportation methods: a) truck-mounted;
b) trailer-mounted.
Parameter value
35,(40),50,70,105
1.2,1.5,2.1,3,6
100，125，150
5.2 Basic parameters
5.2.1 The threads of the joints at both ends of the pipeline with a nominal diameter of 60 and 89 mm shall comply with the provisions of GB/T9253.2, and the trapezoidal threads for joint-to-joint connection shall comply with the provisions of GB/T5796.1~GB/T5796.4. The main matching dimensions of high-pressure joints and high-pressure flexible elbows shall comply with the provisions of SY/T5211. 5.2.2
Other basic parameters are shown in Table 2.
Table 2 Basic parameters of cementing manifold truck
Basic parameter name
Maximum working pressure of manifold
Inner diameter of high-pressure hose
Nominal diameter of high-pressure manifold
Note: (40) is a temporarily reserved parameter
Parameter value
35, (40), 50, 70, 105
6 Types and basic parameters of cementing instrument trucks
6.1 Type
Cementing instrument trucks are divided into the following categories according to their transportation methods: a) truck-mounted;
b) trailer-mounted.
6.2 Basic parameters (see Table 3)
Basic parameter name
Record display displacement range
Cumulative flow range
Flowmeter accuracy
Record display pressure range
Permissible error of pressure display value
Record display relative density range
Downstream ash vehicle model and basic parameters
7.1 Model
7.1.1 According to the mode of transportation, it can be divided into:
a) Truck-mounted;
b) Semi-trailer-mounted.
7.1.2 According to the tank structure, it can be divided into:
a) Vertical tank;
b) Horizontal tank.
7.1.3 According to the type of air compressor, it can be divided into:
a) Piston type;
b) Rotary type;
c) Screw type.
7.2 Basic parameters (see Table 4)
Basic parameter name
Ash loading
Ash unloading speed
Nominal diameter of ash conveying pipeline
Rated displacement of air compressor
Rated pressure of air compressor
Nominal diameter of air pipelinebzxZ.net
SY/T5557—2001
Table 3 Basic parameters of cementing instrument vehicle
Table 4 Basic parameters of cementing vehicle
Parameter value
Parameter value
10,12,15,20
100,125,150
8 Bulk cement tank type and basic parameters
8.1 The bulk cement tank type is vertical.
Basic parameters of bulk cement tank are shown in Table 5.
Basic parameter name
Ash loading capacity
Tank inner diameter × marrow height
Unloading speed
Nominal diameter of ash conveying pipeline
Maximum working pressure
Nominal diameter of gas pipeline
Basic parameters of Kenno truck
Basic parameters of back-tank truck are shown in Table 6.
Basic parameter name
Lifting height
Nominal diameter of ash conveying pipeline
Maximum working pressure
Nominal diameter of gas pipeline
10 Equipment types and basic parameters of bulk cement silo 10.1 Type
SY/T 5557—2001
Table 5 Basic parameters of bulk cement tank
mm×mm
Table 6 Basic parameters of back tank
Bulk cement silo equipment is divided into the following categories according to the tank base structure: a) vertical tank with skid-shaped base;
b) vertical tank with fixed base.
10.2 Basic parameters (see Table 7)
Table 7 Basic parameters of bulk cement storage equipment
Basic parameter name
Single-core ash loading
Nominal diameter of ash conveying pipe
Maximum ash unloading degree
Maximum upper working pressure
Nominal diameter of gas pipeline
Parameter value
2500×6000,3000×6000
100,125,150
Parameter value
2500.3000
400--800
100, 125, 150
Parameter value
50,100,200, 500
10，125,150
11 Types and basic parameters of cementing heads
11.1 Types
According to their connection threads, cementing heads are divided into: a) drill pipe cementing heads;
b) casing cementing heads.
Casing cementing heads are divided into:
a) single-plug casing cementing heads;
b) double-plug casing cementing heads.
11.2 Basic parameters
11.2.1 Basic parameters of drill pipe cement head are shown in Table 8, SY/T 55572001
Table 8 Basic parameters of drill pipe water mixing head
Basic parameter name
Nominal size
Working pressure
Basic parameters of casing cement head are shown in Table 9
Basic parameter name
Nominal size
Working pressure
Table 9 Basic parameters of casing cement head
Parameter value
73,89,127
14, 21, 35, 50, 70, 105
Parameter value
114,127,140, 178, 194,
219,245,273,298,340
14, 21, 35, 50, 70, 105
11.2.3 The thread used to connect the drill pipe cement head with the drilling tool at the wellhead shall comply with the provisions of GB/T9253.1, and the thread used to connect the casing cement head with the casing at the wellhead shall comply with the provisions of GB/T9253.2. 12 Basic parameters of water supply truck
Basic parameters of water supply truck are shown in Table 10.
Table 10 Basic parameters of water supply truck
Basic parameter name
Water tank capacity
Maximum pump displacement
Nominal diameter of pump suction pipe
Nominal diameter of pump discharge pipe
Multiple values
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.