Some standard content:
1C S 37. 100. 10
Mechanical Industry Standard of the People's Republic of China
FB/19116-1999
Folding Machine
Folding machine
1999-07-12Released
State Machinery Industry Bureau
2000-01-01Implementation
JB:T96—1999
This standard is a supplement to ZBJ87011-88 for folding machines. Compared with ZBJ87011-88, the main technical changes are as follows:Added safety guarantee:
Added idling test:
Changed basic data:
Modified blood flow adaptability test:
Modified folding quality test,
This standard replaces ZBJ87011-88 from the date of implementation. This standard was proposed and approved by the Technical Committee of Machinery Standardization. The drafting units of this standard are: Beijing Printing Machine Research Institute, Hunan First People's Machinery Factory. The main author of this standard is Xie Maokun.
This standard was first issued in 1977 and revised for the second time in 1988. Scope
Machinery Industry Standard of the People's Republic of China
Folder
Fuldinu mneine
[R/T9116—1999
This standard specifies the type, folding method, basic data, technical requirements, test methods, inspection methods and markings, loading, transportation and storage of the folding machine.
This standard is applicable to folding machines with single-feed paper. 2. Reference standards
The following standards contain provisions: The provisions of this standard are constituted by any use of this standard. This standard does not include When the edition is completed, all the requested versions are valid. All standard postal services can be subscribed. All parties using the standard can use the latest version of the following standards: GB19—1990
GB/T6388—1986
GB.19969.1—1998
GB/113306—1991
GBT13364-1992
GB/T[4436— 1993
JRT3090—1999
Packaging identification and indication marks
Transport packaging delivery and receipt marks
1Industrial product instructions 1General test
General technical conditions for packaging of electromechanical products
Industrial product guarantee documents, general toilet
Printing mechanical product type guide shrinking method
3Type, basic parameters and folding method
3 .1 Type
3.1.1 Strong product structure is divided into: knife type, grinding fence type, mixed type, 3.t.2 Paper feeding system is slightly divided into: dynamic paper feeding type and hand feeding type, 3.2 Folding method
a) Parallel folding [including fan folding and roll folding, that is, the method of folding parallel to the previous folding edge; ) Vertical cross folding, that is, the method of folding perpendicular to the previous folding edge; mixed folding, that is, the method of folding with parallel and cross folding. 3.3
Basic parameters are shown in Table 1.
3.4 The model and name of the product shall comply with the provisions of JB 3090. Huidong Machinery Industry Bureau approved on 1999-07-12 2000-01-01 Implementation
Extensible products
Paper size
JB/T9116—1999
Table: Basic parameters
Expandable small
=*886 * 1230 546 × 78720U > 75G615×880
393 ×546
2:440x615
308×440
150×2
8c×100
Mud combined
Zutl x3k
1 book controlled automatic folding machine for the public folding machine can be operated according to the specification of the model of the m1 manual folding machine. The maximum production speed of the material sheet m.4 Technical requirements
Sichuan expansion version of the maximum specification state
35--10
52-146
40~#20
On the competition folding time speed
Zhangimin
4.1 The folding machine should meet the requirements of the small standard, and the drawings and technical documents approved in accordance with the prescribed order should be approved. 4.2: The machine should run smoothly, transmit normally, and have no abnormal sound. 4.3 The mechanism is sensitive and reliable, the action of the machine is accurate, without jamming and random movement. 4.4 The brake is sensitive and can be equipped with
4.5 The bearing temperature rise is not more than 354.
4.6 The folding blanket is qualitative
When the folding machine is working, there should be no interruption of paper feeding, double feeding, paper addition, disorderly sheets or uneven collection. The folding error (random error) should not exceed the value in Table 2. 4.7
Table 2 Folding error
Mold-bar type
Rope type
4.8 Maximum bending
(parallel folding)
Household 5
[Vertical cross analysis]
Bottom angle;
110125
Bottom angle,
The noise of knife-type negative machine is not B: The noise of book-type and mixed folding machine is not greater than H (4 .9 Safety protection functions should be complete and measurable
4.10 Electrical quality
40,1 The electrical equipment should be flexible and reliable, the wiring should be complete, and all kinds of markings should be complete and correct. JB9116-1999
4.2 The insulation resistance between the short-circuited power circuit and the protection circuit (including the rear seat) should be not less than 1M04.0.3 Electrical equipment should be tested with 1500V50H! for 1s, and there should be no breakdown. The insulation resistance between the external protection wire terminal and any conductive parts of the equipment and the body should be less than 0.1.4.11 Appearance quality
4.11.1 The cross-layer of the product should be flat and smooth, and the color should be glossy. The paint should not have sagging, bubbling, etc. 4.11.2 The appearance of the product should not have rust, group damage and other defects. 4.1.3 The appearance of the product should be better than the appearance of the product. 4.12 Product specifications:
R) Page extension machine:
! Replacement for maintenance and expansion of the necessary work:
c) Necessary accessories section easy to prepare
5 Test method bZxz.net
5.1 Test conditions
5.1. Test requirements:
8) The cut edge has a line width not greater than: 000: 0.25: b! The vertical angle of the cut adjacent edges is not large F1:
Center) The test paper shall not be damp, rubbed, curled, torn, wrinkled and other defects. 5.1.2 Test environment:
a) Ambient temperature 15-359:
h: Relative humidity 40%-5%
5.1.3 Test instrument and its specifications:
a1 Rotation meter: ±rmin:
b1 Transfer meter: 0.01s:
c) 10x reading microscope, accuracy is D.Imm: d) Ordinary sound level:
e! Surface thermometer
5.2 Idle running test
Turn the machine at low speed for 30mm, medium speed for 1h, high speed for 30mi, check the machine operation, it should meet the requirements of 4.344.4.5, 4.9, 4.3.
5.3 Folding adaptability test
5.3.1 Thick paper test:
a) Use the machine to fold the paper with the largest size, the length and width are less than 85% of the maximum foldable paper size; h) The folding speed is not less than 70% of the maximum speed of the machine; ) Fold at least 100 sheets continuously and stably, at least twice, including the mixed type folder, fence type, and type 9 each time. 5.3.2 Thin paper test:
| ) Use the machine to determine the minimum amount of continuous sheets, the length, feel no less than 10% of the smallest paper size that can be folded: B5% 3
6, folding length is unlimited:
91161999
Continuously fold 100 sheets in each group! 5.3.3 Minimum group test
1) Use 52-100m flash note ~ a kind of paper, size is the rated minimum foldable paper size of the machine end: b: the printing speed is the rated maximum speed; :) Although the machine determines that the folding is not less than sheets.
5.3.4 Large-volume paper non-test
Use 2-m paper, size is the maximum paper size that the machine can fold; h; the speed is not less than ten times the rated suction speed of the machine; 】Continuously test the stability of each folding standard for more than 1 year [maximum folding speed 5.4 Page stability test:
a] Use 52-100 dots/m2 f-type paper, length, width not less than R5% of the rated maximum foldable sheet size of the machine; b) The folding speed is 80% of the rated maximum speed of the machine; c) Continuously fold each page to the stable standard for more than 1 minute (maximum folding speed 5.5.5.1 Folding accuracy test
5.5.1 Folding
) Use any paper within the 5280m standard size: length and width are not less than 85% of the maximum paper size that the machine can fold: b: Folding speed is not less than % of the maximum speed set by the machine: Continuously change the group mark (maximum four folding pages
in the continuous folding and pasting 000 sheets, randomly throw out 0 accounts: 5.5.3 Inspection
5.5.3.1 For the part shown in the figure, turn it over on the table and determine the plane alignment system, which is parallel to the measuring reference line of the vehicle, OH=(L2)10, mm; and determine the side (selected by reference) JB/T9116-1999 b! The a-side of the folding sticker shown in the figure is the front standard side, and the side a is the second standard side when folding; 】 The folding is close to the axis, and the first folding sticker is measured from the sight line t to the distance a. The measured value is negative, otherwise it is positive: d) Use formula (1) to calculate the side error e, or: x-+
sticker serial number:
Chinese number:
total number of sample stickers,
5.5.3.2 bottom angle
let? Continue with the end shown in Figure 2 (when at the first fold, it is the specified starting edge, and the first fold and subsequent folds are on the edge of the previous fold pd = a.
b) Let the intersection of dd and the folded edge be (see Figure 2) as the center of the grid: d is the radius and the other side is the intersection point p; c) the chord length of the disk arc (that is, the length of the line segment; and determine the positive and negative according to the two deviation directions shown in Figure 2); d) calculate the base angle difference according to formula (2):
In the formula: 3-26,;
Sample number:
.—Number of folds:
Total number of samples.
5.6 Noise measurement
5.6.1 Use any paper within the range of 52~100m, the size is the size of the paper that can be folded by the machine, the rate is the machine's quantitative height,
5,6.2 The measuring points are shown in Figure 3, the 5th point is the highest point on the imaginary envelope line of the machine, the measuring plate's height is the same as the machine's height and half of it
5.6.3 The noise level shall be calculated according to the technical level of each measuring point, and shall comply with the provisions of 4.9. The appearance quality of the product shall comply with the provisions of 4.12 of the enterprise, and the inspection rules
6.1 Factory inspection|| tt||6.1.1 Each product shall be inspected in 5.2 and 5.5, and only qualified ones can be shipped out. tt||6.1.2 Product sampling inspection includes: 1 unit is selected from 5-10 units in the batch; 2 units are selected from 11-30 units, and all items except 35.3, 5.4, and 5.6 are inspected on the same day; 1. If the batch is larger than 5 units, the first batch of samples shall be inspected one by one. If there are unqualified items in the sample inspection, additional samples shall be required, and all items shall be inspected: 6.1.4 If there are unqualified items, they shall be inspected one by one, and 3 units shall be inspected if the standard difference is used for the items. 6.2 Type inspection
6.3. If there is any missing item, 1 unit in the first batch or the first batch shall be inspected: a! 6.2.2 Type inspection standard version of the product shall be marked with full details. 7. Each product shall be marked with a label in the visible position. The length of the label shall comply with the provisions of GR/T [3306] and its contents shall include: a) manufacturing name; 5) product number and name:
Production mark:
d) manufacturing date (or serial number or batch number TBT9116-1999)
7.2 The packaging mark shall comply with the relevant provisions of GB191. 7.3 The shipping and receiving marks of the product shall comply with the relevant provisions of GH6388 9 Packaging, transportation, Storage
8.1.1 Before product packaging, the exposed surfaces of the machine, parts and accessories should be coated with anti-rust agent. 8.1.2 Product packaging should comply with the relevant provisions of GB/T13384. 8.1.3 Random Documents
When each product is shipped, the following documents must be provided: a) Product certificate
The preparation of the product certificate should comply with the provisions of GB/T13384; b) Product instruction manual
The product instruction manual should comply with the provisions of GBF9969.1; c) Packing list:
d) Installation drawing.
8.2 Transportation
When transporting the product, it should be placed carefully according to the marks on the outside of the packaging to prevent it from being damaged. 8. 34
The product should be stored in a dry and wind-proof place to avoid deterioration. If necessary, take rain-proof measures. If the product is stored for more than 2 years, please check the product before purchase. If the product packaging is found to be smaller than the relevant regulations, please repack it.1 Before product packaging, the exposed surfaces of the machine, parts and accessories should be coated with antirust agent. 8.1.2 Product packaging should comply with the relevant provisions of GB/T13384. 8.1.3 Random Documents
Each product shall be shipped with the following documents: a) Product Certificate
The preparation of the product certificate shall comply with the provisions of GB/T 4436; b) Product Instructions
The product instructions shall comply with the provisions of GB/T 9969.1; c) Packing List; d) Installation Drawing.
8.2 Transportation
When transporting the product, it shall be carefully placed according to the markings on the outside of the packaging to prevent damage. 8.34
The product shall be stored in a dry and wind-proof place to avoid deterioration. If the storage period exceeds 2 years, unpack and inspect before shipping. If the product packaging is found to have exceeded the relevant provisions of the relevant regulations, repack it.1 Before product packaging, the exposed surfaces of the machine, parts and accessories should be coated with antirust agent. 8.1.2 Product packaging should comply with the relevant provisions of GB/T13384. 8.1.3 Random Documents
Each product shall be shipped with the following documents: a) Product Certificate
The preparation of the product certificate shall comply with the provisions of GB/T 4436; b) Product Instructions
The product instructions shall comply with the provisions of GB/T 9969.1; c) Packing List; d) Installation Drawing.
8.2 Transportation
When transporting the product, it shall be carefully placed according to the markings on the outside of the packaging to prevent damage. 8.34
The product shall be stored in a dry and wind-proof place to avoid deterioration. If the storage period exceeds 2 years, unpack and inspect before shipping. If the product packaging is found to have exceeded the relevant provisions of the relevant regulations, repack it.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.