This standard specifies the type, size, technical requirements and test methods of collector rings and brush holders for large AC motors. This standard is applicable to large AC motors of general structure. The collector ring bracket is installed on the motor shaft, and the brush holder is installed on the seat bearing or other parts of the motor. JB/T 2650-2000 Large AC motor collector rings and brush holders JB/T2650-2000 Standard download decompression password: www.bzxz.net
Some standard content:
Mechanical Industry Standard of the People's Republic of China JB/T2650 一创蔷護 2000-04-24 瓦鱻极懂 2000-10-01小 JB/T26502000 This standard is a revision of IB2650-79 "Types and sizes of large AC motor collector rings and brush holders". JB265079 was first promulgated and implemented in 1979 and reviewed and confirmed in September 1987. This revision is based on the standard confirmed in 1987, and mainly makes the following 5 changes: 1 The original standard name "Types and sizes of large AC motor collector rings and brush holders" was changed to "Large AC motor collector rings and brush holders". 2. Change the 2nd article of the first chapter of the original standard to the 3.2nd article of the current standard, and change the content to "…type and size are generally in accordance with…" "collector rings are generally connected\ 3. Correct the marking errors in Figures 1, 2 and 3 of the original standard4. Change the 5th article of the second chapter of the original standard to the 4.1st article of the current standard, change "JB2359-79" to "GB/T[2351\, change \surface coating and painting shall be in accordance with JB/Z88--75 electroplating net of tropical electrical products and JB/Z90-75 tropical electrical products respectively. The regulations for the painting of products are changed to "the coating and painting of the decay surface shall comply with the relevant regulations of Taiwan" 5. Table A1 in Appendix A is changed to a linear table. This standard replaces B2650-79 from the date of implementation. This standard is proposed and managed by Harbin Thermal Power Plant Research Institute. The drafting units of this standard are: Dongfang Electric Co., Ltd., Shanghai Electric Plant Co., Ltd., Harbin Electric Plant Co., Ltd., and Lanzhou Electric Plant Co., Ltd. The main drafters of this standard are: Zhu Changqian, Li Hong, Jin Gaohua, Chen Run Year, Mulan. This standard was first issued in 1979, and was confirmed in the summer of September 1987. This is the first revision. 1 Scope JB/T26502000 JB265079 This standard specifies the type, size, technical requirements and test methods of the collector ring and brush holder of large AC motors. This standard is applicable to large AC motors of general structure. The collector ring bracket is installed on the rotating shaft of the motor, The brush holder is installed on the seat bearing or other parts of the motor. 2 Cited standards The clauses contained in the following standards constitute the clauses of this standard through reference in this standard. When the standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T12351—1990 Technical requirements for tropical type rotating motor environment GB/T12973—1991 Commutator and collector ring dimensions JB/T 2361—1992 3 Types and dimensions Constant pressure brush holder 3.1 The outer diameter size series of collector rings in this standard meets the requirements of GB/T12973 and is specified as: 355, 400, 450, 500, 560, 630710 and 800 mms 3.2 The types and sizes of synchronous motor collector rings and brush holders are generally in accordance with Figure 1 and Table 1. The collector rings with higher speeds are generally in accordance with the form of Figure 2. HIS Va 2000-04-24 2000-10-01 Small cable Collector ring diameter Frame (mm) [45~165 130~150 JB/T26502000 Number of brushes per collector ring Note: When the number of brushes per collector ring is large, the brush holder can be placed on both sides of the collector ring. 3056. 5bzxZ.net 3.3The types and dimensions of the collector rings and brush holders of asynchronous motors shall be in accordance with Figure 3 and Table 2. 2 Applicable bearings Diameter (mm) Collector ring diameter Inner diameter of bracket JB/T26502000 Number of brushes per collector ring (pieces) Note: When there are many brushes per collector ring, the brush nest can be divided into two parts. 12 Applicable bearings Diameter (mm)) JB/T2650 3.4The installation dimensions of the brush holder on the seat bearing shall be in accordance with Figure 1, Figure 3 and Table 3. Table 3 Bearing diameter 110~130 140-160 180-200 220~230 280-320 360-400 450-500 3.5The thread accuracy grade in this standard is all grade 6. 4 Technical requirements 4.1 When the collector ring and brush holder are used in tropical pool areas, they shall comply with the provisions of GB/T12351, and the surface coating and painting shall comply with relevant regulations. 4.2 The brush support adopts the HZ12 type in JB/2361, and the size of the brush t×a is 32×25. When the brush box material is a gold fan, the top of the brush should be insulated to prevent damage caused by current flowing through the constant pressure spring. 4.3 The coaxiality tolerance between the outer circle of the collector ring and the inner circle of the bracket shall be in accordance with the provisions of Table 4. Table 4 Electric ring diameter 355-500 560-800 Coaxiality Note: If the outer circle of the Huadian ring needs to be processed after it is installed in the motor, the coaxiality between the outer circle of the collector ring and the rotating shaft should be assessed. 4.4 Insulating partitions should be added between the conductive plates of the brush holder to prevent accidents such as short circuits. 4.5 The surfaces of various insulating parts should be smooth, without protrusions and flash. The surfaces that have been cut must be treated with insulating paint dip and baking. The plastic parts used for ground insulation should be sealed with negative resin before the collector ring can be installed. 4.6 Insulation level: The collector ring and brush holder are both Class B. 4.7 Operating voltage: The collector ring and brush holder for Shangbu motors are below 500V, and the collector ring and brush holder for asynchronous motors are below 1500V. 4.8 See Appendix A for the applicable speed of the collector ring 5 Test method 5.1 After the collector ring is assembled and processed, it should be subjected to the AC insulation dielectric strength test to ground. The test time is 1min: Test voltage (effective value) is as follows: Synchronous motor collector ring: not less than 4500V Asynchronous motor collector ring: 2+2500V (for unidirectional rotating motors) or 4Ug+2500V (for forward and reverse rotating motors) Where: x Rotor open circuit voltage, V. 5.2 If other test items are required in the motor technical conditions, the test methods shall be in accordance with the relevant technical documents. 4 Applicable speed of the collector ring is shown in Table A1. Outer diameter of collector ring JB/T26502000 Appendix A (Suggested Appendix) Applicable speed of collector ring No protection Ring (Figure 1) With protective ring (Figure 2) One cut quangan JB/T2650 lai880b1230 19XXXXling 100044 WanduanX/X TravelXXX,XXX 19XXjiXXcabin LengXdai DepxXX.XXwing Xianjioupai Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.