JB/T 9005.5-1999 JB/T 9005.5-1999 Casting pulley for crane, type B JB/T9005.5-1999 Standard download decompression password: www.bzxz.net
Some standard content:
JB/T9005.5—1999 This standard adopts D1N15418:1982 Part 1 to Part 3 "C-type wire rope pulley" in a non-equivalent manner. This standard is a revision of ZBJ80006.5-87 "Cast pulley type B for cranes". During the revision, only editorial changes were made to the original standard, and the main technical content remained unchanged. This standard is part of the JB/T9005 series of standards "Cast pulleys for cranes", which includes the following 10 parts: JB/T 9005. ---1999 JB/T 9005.2- JB/T 9005.3—1999 JB/T 9005. ---1999 JB/T 9005.5—1999 JB/T 9005. 6-1999 JB/T 9005. 7—1999 JB/T 9005.8 JB/T 9005. 9-1999 Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Rope groove section Diameter selection series and matching Type, hub and bearing size JB/T9005.10-1999 Technical conditions Cast pulley for crane This standard replaces ZBJ80006.5-87 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Hoisting Machinery. The responsible drafting unit of this standard: Dalian Daqi Group Co., Ltd. The main drafters of this standard are Zhou Yu'an and Cui Zhenyuan. 421 1 Scope Machinery Industry Standard of the People's Republic of China Casting sheaves for cranes Type B- Casting sheaves for cranesJB/T 9005.5--1999 Replaces ZBJ80006.5-87 This standard applies to cast wire rope pulleys (hereinafter referred to as pulleys) with rolling bearings and no inner sleeves that require tight sealing within the scope of crane movable pulley blocks. Other pulleys in wire rope transmission, such as fixed pulleys or other load-bearing parts except movable pulley blocks, can also use pulleys specified in this standard. 2 Referenced standards The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T931987 Standard spring washers GB/T276-1994 Rolling bearings Deep groove ball bearings Dimensions GB/T283-1994 Rolling bearings Cylindrical roller bearings Dimensions GB/T5782--1986 Hexagonal head bolts Grade A and Grade B GB/T 6170-1986 I-type hexagonal nuts Grade A and B GB/T9877.1--1988 Rotating shaft lip seals Structural dimensions series Part 1: Internal skeleton rotating shaft lip seals 3 Types and dimensions 3.1 Type B pulleys are divided into Type B, (with deep groove ball bearings) and Type B, (with cylindrical roller bearings) according to the different types of rolling bearings they use. The types and dimensions of Type B pulleys are detailed in Figure 1 and Table 1. Marking example: Wire rope diameter d = 25mm, pulley diameter D = 630mm and diameter D, = 90mm B-type pulley, marked as: pulley B, 25 × 630-90JB/T9005.5-1999National Machinery Industry Bureau1999-06-28Approved422 2000-01-01Implementation JB/T 9005.5 -. 1999 Figure 1B type Rolling bearing code Hexagon head bolt hexagon nut GB/T5782 According to GB/T276According to G13/T283 (Extended) M8×75 M10X85 M10×90 M10×90 M10×105 M10X10 M10X120 M10X125 M12×130 M12×130 Spring washer GB/T6170GB/T93 Bolts, nuts Nuts and springs Number of washers 360135 JB/T9005.5-1999||tt ||Table 1 (end) Code of rolling bearing Hexagon head screw hexagon nut Spring washer bolt, screw nut and spring GB/T5782 According to GB/T276 According to GB/T283 (extended) GIB/T6170GB/T93 M12×140 M12X1 45 M12×155 M12X155 M12X160 M12×165 M16×190 Note: To facilitate the installation of the pulley, the axial clearance on each side should be specified to be at least 1mm in the connection structure. For the dimensions of the spacer sleeve (AT or BT) and spacer ring (H) for 3.2B type pulley, please refer to Figures 2 to 4 and Table 2. Marking example: The spacer (AT) for the B-type pulley with diameter D = 90mm is marked as: spacer AT90JB/T9005.51999 The spacer (BT) for the B-type pulley with diameter D = 90mm is marked as: spacer BT90JB/T9005.5—1999 The spacer (H) for the B-type pulley with diameter D = 160mm is marked as: Spacer ring H160JB/T9005.5-1999 (When installing one pulley on the pulley shaft)Figure 2 Spacer sleeve (AT) (B,=2B,-5) (When installing multiple pulleys in parallel on the pulley shaft)Figure 3 Spacer sleeve (BT) Number of washers Figure 4 Spacer ring (H) Sleeve (AT) Weight of a single piece! JB/T9005.5—1999 Sleeve (BT) 1) When multiple pulleys are installed in parallel on one shaft, the length of the spacer sleeve (BT) is B=2B;5. Unit weight 3.3 The dimensions of the cover (AG or BG) for type B pulley are detailed in Figure 5 and the specified marking examples in Table 3: Shaft seal cover (BG) for type B pulley with diameter D) = 160mm, marked as 1), Ring (H) Unit weightbzxZ.net JB/T9005.5—1999 Cover BG160 JB/T9005.5—1999 Groove seal cover (AG) Enlarged part II Shaft seal cover (BG) Figure 5 Cover Enlarged part 1 JB/T 9005.5 --1999 Kidney-type rubber Oil seal according to GB/T 9877.1 | | tt | | 70 × 95 × 10 | | tt | | 80 × 105 × 10 | | tt | | 80 × 105 × 10 | | tt | 0×170×12 140×180X15|| tt||150×190×15 160X200×15 170×200×15 180×210×15 190×220×15 200X230X15 220X250X 220×250× 240X270 Weight per piecekg Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.