Some standard content:
ICS37.100.10
Machinery Industry Standard of the People's Republic of China
JB/T104522004
Office Equipment
Book Binding Machine
OfficeEquipmentBookBindingMacchinc2004-03-12Published
2004-08-01Implemented
Published by the National Development and Reform Commission of the People's Republic of ChinaForeword
StandardizationIntroduction to the BureauList
3 Evaluation and determination of the branch
4 Technical requirements.
Drawing number
Working conditions,
Transportation resistance, medical performance
Appearance quality
Safety performance
General performance
Test method.
Marking and packaging anti-loosening inspection
Transportation resistance, storage test
Less flower tribute inspection
5.4 Gold performance system test
Performance analysis code test
Noise test,
6 Inspection rules.
Inspection of whole ticket..
Delivery "strike"! Inspection
K3 type inspection
? Marking creation, transportation and storage. .
Table: Special transport, storage test conditions and methods for card text binding machine inspection and verification
Table 5 Type inspection and verification
JB/T10452—2004
JE/T10452-2004
This standard is formulated for the first time,
The reason for this standard is proposed by China Machinery Industry Federation. Foreword
This standard is issued by the National Photocopying Machine Standardization Technical Committee (SATI47) and is drafted by FI. The drafting units of this standard are the National Photocopying Machine Standardization Technical Committee, the National Photocopying Machine Quality Supervision and Inspection Center, and the Office Equipment Factory of Youzhong Weigong Machinery Co., Ltd. The main authors of this standard are Xuan Zunping, Ke Ru, and Yang Lujun. 11
1 Scope
Office document binding machine
R/T10452—2004
Nature This standard specifies the technical requirements, test methods, inspection rules and requirements for marking, packaging, transportation and storage of office document binding machines
This standard is mainly applicable to common document binding machines such as hot press type, screw type, iron ring type, hot melt type, etc. Other document binding machines may be approved.
2 Normative references
The clauses in the following documents become the clauses of this standard through non-standard references. For any document with a specified date, all its revisions (not including the revised version) and other revisions are not applicable to this technical standard. However, it is encouraged to study whether the latest versions of these documents can be used in accordance with this standard. For any referenced document without a date, the latest version shall apply - this standard: GBIT191-2OD Packaging storage and transportation graphic signs [EVIS7RO: 1997) CB1002-1996 Use of similar purpose single-phase plug and socket type, basic size and integer G0/T2829-2002 Inspection counting sampling procedures and detailed sampling tables for process tax qualitative inspection B4943-: 2001 Information technology equipment safety (IDC60950: 1999; GR9969.1-1999 Industrial product instruction manual GB/T13306.-1991 Labels
GB/T1443G13 Industrial product guarantee documents are collectively called GR/T 15I64199S
Receiver instrument packaging general technical system
B1593419 wire parts (E099: 1984
JB9444.1--11-1999 E1 Mechanical basic environmental test method (ev[EC6K68) 3 Terms and definitions
The following terms and definitions are used in this standard
Heat press binder hernalpressedbinder to make the product line, read the punching, use the thermoplastic material to heat the potassium, and complete the war document 3.2
Plastic window binder perfu-binder
Uses a film or self-perforating method to punch holes in the document binding line, and uses plastic tubes for binding: 3.3
Plastic binder plasliebiimder
Uses a method to punch holes in the document binding line, and the machine lifts the cavity circle to put the document on the stock map and then binds it into a binding device 34
Wire binder wirebinder
Uses a mechanical method to punch holes on one side of the document binding line, The machine opens the loop, and the document is wrapped and then the document is made into a binding machine. The hot melt glue binder cutter
JB/T10452-2004
No collar punching, and the matching document envelope is coated with a layer of binding blood, which is heated by the device and then adhered to the text. After cooling, the binding machine is launched, so as to achieve the binding function. 4 Technical requirements
4.1 Graphic symbols
The graphic symbols related to the product and the enterprise shall comply with the provisions of GR4943. 4.2 Working conditions
The product should be able to work normally under the above conditions, and the main technical indicators should meet the requirements of the enterprise's product specifications. 4.2.1 Working environment conditions
a) Temperature: 0~35℃;
b) Relative humidity: 10%--80%.
4.2.2 Working voltage and frequency
): 220:1±10%)V:
h) Relative temperature: 50TIz...
4.3 Transportation and storage performance
The product can withstand the test specified in 1 under packaging conditions. After the test, the machine should be packed in good condition and all technical indicators meet the requirements of this standard. Table
Transportation and storage test conditions and methods
Test frequency
Contact the added movement
Set near heat
4.4 Appearance quality
Parts and components
According to the provisions of B door 5444.9, select 18, 6HZ and connect the standards of B door 9444.8
According to the provisions of 91-14.2, 2513Y
Occasionally, the inferior effect
freely missing the head. According to the definition of JB/T9444.4, 4.4.1 The appearance of the product shall be flat, bright and clear, without any marks on the surface. Parts that may affect the appearance quality of the product shall be subjected to necessary rust treatment: the quality of the electrostatic coating, chemical and rust-proof coating shall be smooth, without bumps, protrusions and uniform color. 4.4.2 The surface of the plastic shall be flat, bright and uniform in color, without any defects such as cracks, bubbles and shrinkage holes. 4.5 Safety performance
4.5.1 Dielectric strength
Add 501Iz, AC13NV voltage between the power supply line and the ground line of the product, and the product will be safe after 60 seconds. 4.5.2 The type and type of the power plug, socket or wire assembly power head, socket and power cord should comply with the requirements of GB1002 and GB1531. 4.5.3 Grounding performance
The grounding performance of the product complies with GB4943-2 001.2.6.3.3, 2.6.3.4, 2.6.5.6.4.5.4 Contact current
The product's contact current shall not be 3.STA,
4.5.5 Structural requirements
All structures shall be intact and undamaged, and connections shall be reliable. Fasteners shall not be damaged. The operator's sensitive contact area (such as plugs, sockets, etc.) shall be rounded and light-proof: The binding sheet shall not have hair that can scratch the human skin at the binding site. 4.5.6 Electric shock protection
Human contact must not be dangerous. 4.5.7 Marking and instructions
1 Marking and instructions must comply with the requirements of GB4943.7 2
4.6 Performance and function
The following items and indicators should be specified in the enterprise's application: Binding firmness: Bias force N:
b Maximum binding length: in mm:
) Maximum binding thickness, in M!
Maximum hole thickness, in other words
e) Binding time, in other words
Bamboo hole margin deviation: I spacing deviation, in mm: Punch diameter, in mu:
h) Hot pressing binding accuracy:
Hot pressing (hot melt) binding accuracy, in units of death. 4.7 Noise limit
The maximum noise of the product should be less than 70dB(A).
5 Test method
5.1 Inspection of labeling and packaging
Inspect the packaging, labeling and packaging integrity. 5.2 Transport and storage test
Carry out the test according to the requirements of Table 1 and the methods specified in BT9444. 5.3 Appearance quality inspection
Inspect whether the product appearance meets the requirements of 4.4. 54 Safety performance test
5.4. Anti-electric strength
JK/T10452-2004
When the product is not powered on, put the product in the disconnected position, connect the power plug of the product to the power supply, and then apply a 1500V voltage of 50H frequency between it and the ground wire of the power supply, or the current is IImA. After 0s, check whether the product insulation is good: 54.2 Check the power plug mark, plug mark or wire assembly mark, and the type of flexible cord in the power plug, socket or wire assembly. 54.3 Grounding performance
2) When the product is not powered on, according to (34043-2001 2.6.1.3 Measure the grounding conductor and the connection resistance value according to the specified method. The test instrument is not subject to the soil 5%: 5 According to the method specified in 2.6.3.4 of GB4943-2001, check whether the grounding color of the protective cover meets the requirements of the standard: c! According to the requirements of 2.6.5.6 and Appendix of GB4943-2001, check whether the connection meets the requirements of the platform resistance. 5.4.4 Contact current
Product compensation ratio
According to the single-phase equipment inspection method of 5.1 of GB4943-2001, the test instrument accuracy shall not be less than 3.5% 5.4.5 Structural requirements inspection
Daily inspection of the machine.
5.4.6 Electric shock protection
Connect the test finger according to the method specified in 2.1.1 of GB443-2001. The product is qualified. During the test, the test will be stretched straight, without obvious sand, and the two or more hazardous energy levels will not be bridged. 5.7 Marking and instructions
Check the markings and instructions on the product, and they should meet the requirements of 4.5.7. 55 General performance and function test
5.5.1 Binding firmness
JB/r10452—2004
Use the paper with the maximum length of the enterprise standard to bind the maximum length. Monthly inspection or use: point force method inspection: The enterprise standard should specify the method for checking the firmness of the binding of various products. After inspection or test, the text should remain intact and solid, and should not be extremely scattered: maintain more, 5.5.2 Record the length of the binding seat || tt||For the products that have passed the binding firmness inspection or the test, use a vernier caliper to measure the maximum length, which should meet the standard value specified in the enterprise standard. 5.5.3 Record the maximum binding thickness
For the products that have passed the binding firmness inspection, use a vernier caliper to measure the thickness of the binding part of the text sheet (excluding the binding material): it should meet the requirements of the enterprise standard. 5.5.4 Maximum punching thickness
Based on the specified value of the enterprise standard, take the paper of corresponding thickness and punch it at one time, and use a vernier caliper to adjust the thickness: check whether the paper after the hole is evenly inserted, neat, and there is no hair on the hole. 5.5.5 Binding timeWww.bzxZ.net
Use the industry standard to measure the maximum length and quantity of the punched paper, and use a stopwatch to record the time for binding into a book. It should meet the specified value of the enterprise standard. 5.5.6 Hole margin deviation, hole spacing deviation
Use 10 sheets of 70mm paper to punch at the maximum binding length, and take 3 of them to measure the distance between adjacent hole trays and the distance between hole trays. Take the maximum error as the confirmed result: ※It can meet the requirements of the enterprise standard. 5.5.7 Punching diameter
Use paper that has been punched according to the industry standard to punch holes, and do not bind after punching. Use a vernier caliper to check the diameter of the holes: It should meet the specified position of the enterprise specification,
5.5.8 Hot pressing binding speed
Use the maximum length specified in the enterprise standard to bind the paper with the binding thickness and the already punched paper, use an electric meter to time, and record the difference between the thermoplastic material and the specified value of the enterprise standard. 5.5.9 Overpressure: Hot melt) Transfer temperature
Stick the flow meter sensor probe to the left, right, and right sides of the machine where the heat is generated (there are three places): the left and right sides of the machine where the heat is generated (the maximum temperature should be the test result). Its temperature value should meet the specified value of the enterprise standard, and there should be no snow scratches on it. 5.6 Noise test
Under the condition that the circulating noise is less than 1UBA: Place the machine on the cement evenly, and install it at the front, rear, left and right of the machine according to the most people: Use a sound level meter (A) to verify that it can meet the requirements of 4.7. 6 Inspection rules
6.1 Inspection classification
Product inspection is divided into delivery inspection (factory inspection) and type inspection. 6.2 Acceptance (ex-factory) inspection
5.2.1 Acceptance (ex-factory) inspection items H and unqualified categories are shown in Table 2, Table 2 Text machine inspection items table
Inspection source ||tt| |Packing, transportation
data, prohibited
and appearance
required name
continuous lack of test
low quality
creative packaging only
packaging complete
external quality
corresponding to the terms
not special
enterprise
-function
and||environmental protection
test function
items
return to the source
remove the socket or wire
the complete
requirements
clearly state the anti-sabotage
label instructions
|tt||Installation design and output speed
Maximum agricultural length
Exhibition of real ordering team
People's University punching pressure
Binding room
Binding room, hole cutting difference
Binding path
Hot E binding process
Table 2 continued:
City miscellaneous items
Technical requirements
Inspection methods
The machine must be inspected by the factory quality inspection department and the price will be confirmed before leaving the factory 6.2.2
Small size category
JB/T1Q452
6.23 Delivery inspection and improvement of efficiency. If there are unqualified items, make corrections at the end and re-inspect the quality before delivery! 6.2.4 Acceptance inspection items are not subject to full inspection or random inspection. The inspection batch, sampling plan and inspection level of acceptance inspection shall be specified in the enterprise standard: 6 Type inspection 6.3.1 Production type inspection shall be conducted in the following cases: 1) When new products are submitted: 2) When the production time is confirmed: more than one year or more: 3) When the product is in major political construction such as design, engineering, and financial rate, all relevant changes shall be made according to the changes. 4) When the national quality supervision organization proposes the requirements for late type inspection: 6.3.2 The whole machine sample of type inspection shall be inspected from two qualified products in the same batch. 6.3.3 Judgment rules
6.3.3.1 Inspection items and non-conforming categories of unit products in the sample input table 2, 6.3.32 Type inspection lot judgment method
) Column 3 Unit product safety GRT 2829 one change sampling plan, judgment half option 1, do not put the level and complete the group in this table 3.
Table 3 Type inspection judgment
Non-conforming category
Non-conforming road quality half
+: Number of technical indicators and two reductions in total number of continuous judgment to custom-made women
Code number: Ac
Technical delay number (Re!
JR/T10452-2004
) If the type inspection fails, the product will not be accepted by the manufacturer or factory for marking, packaging, transportation and storage ||tt| |7.1 Packaging and labeling:
7.1.1 The nameplate of the product shall be fixed on the product position and marked with the following information: the actual size shall comply with the provisions of (8B/11336):
a) Manufacturer:
b) Product name, model or mark
c) New product: V), rated frequency (Hz, rated power (W):
d) Production date and production number,
7.1.2 Packaging and labeling: The packaging requirements shall be in accordance with the relevant provisions of GB/T19GB154. The packaging shall be valid for 5 years as specified in the enterprise standard. The old age shall not be less than 15 years. The color roller shall ensure that under normal transportation and purchase conditions, the machine will not be damaged by the frequency version, loading and unloading, tide or dust!
7.1.3 The packaging box shall be accompanied by the following content in Chinese: Production certificate. The preparation of product certificates should comply with the current provisions of GB/T14436: h)> Product instruction manual. The numbering of product instruction manuals should comply with the provisions of G9969: C Packing list,
7.1.4 The packaging conditions of the product should be able to prevent decay, expansion and safety, 7.1.5. The product packaging is in accordance with the provisions of BT15464, and the following marks are on the box: a) Product name and model:
b) Manufacturer:
c) Product standard number:
d) "Handle with care", "Avoid moisture", "Limited number of layers" and other graphic marks are in accordance with the provisions of BT191. 7.2 The product should be stored in the warehouse according to the original packaging condition. The warehouse should be well ventilated, the air should be dry and free of corrosive gases and machine-generated gases. The long-term storage environment humidity should be 5-35℃, and the relative humidity should not exceed 90%. 7.3 The storage height of the product should not exceed the requirements marked on the packaging box. The storage period of the product should not exceed two years. For products that exceed this standard, it is prohibited to transport them directly without being exposed to rain, sunlight, or pressure.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.