title>Series 1 freight containers00Specification and testing--Part 1:General cargo containers for general purposes - GB/T 5338-2002 - Chinese standardNet - bzxz.net
Home > GB > Series 1 freight containers00Specification and testing--Part 1:General cargo containers for general purposes
Series 1 freight containers00Specification and testing--Part 1:General cargo containers for general purposes

Basic Information

Standard ID: GB/T 5338-2002

Standard Name:Series 1 freight containers00Specification and testing--Part 1:General cargo containers for general purposes

Chinese Name: 系列1集装箱 技术要求和试验方法 第1部分:通用集装箱

Standard category:National Standard (GB)

state:Abolished

Date of Release2002-01-08

Date of Implementation:2002-10-01

Date of Expiration:2023-09-01

standard classification number

Standard ICS number:Packaging and transportation of goods>> Freight transportation>> 55.180.10 General purpose container

Standard Classification Number:Comprehensive>>Marking, packaging, transportation, storage>>A85 container, pallet, shelf

associated standards

alternative situation:GB/T 3219-1995 GB/T 5338-1995

Procurement status:idt ISO 1496-1:1990

Publication information

publishing house:China Standard Press

ISBN:155066.1-18748

Publication date:2002-10-01

other information

Release date:1985-08-31

Review date:2004-10-14

drafter:Hins Cheung, Si Shuyun, Zhang Binghua, Shi Yanqiu, Li You, Zhao Jie, Qi Xiangchun

Drafting unit:Ministry of Transport of the People's Republic of China

Focal point unit:National Container Standardization Technical Committee

Proposing unit:Ministry of Transport of the People's Republic of China

Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

competent authority:National Standardization Administration

Introduction to standards:

This standard specifies the technical requirements and test methods for Series 1 containers (closed, breathable, ventilated and open top), and is applicable to containers used for international exchange and water, road, rail transport and their combined use. This standard applies to the following types of containers: Type code: 00 to 04 Type: Closed, including top opening; Type code: 10, 11 Type: Closed, with vents; Type code: 13, 15, 17 Type: Closed, with ventilation facilities; Type code: 50 to 53 Type: Open top. This standard does not involve requirements for ventilation and ventilation facilities. Requirements for relevant markings are specified in GB/T 1836-1997. GB/T 5338-2002 Technical requirements and test methods for series 1 containers Part 1: General purpose containers GB/T5338-2002 standard download decompression password: www.bzxz.net
This standard specifies the technical requirements and test methods for series 1 containers (closed, breathable, ventilated and open top), applicable to international exchange and water, road, rail transport and their combined use containers. This standard applies to the following types of containers: Type code: 00 to 04 Type: closed, including top opening; Type code: 10, 11 Type: closed, with vents; Type code: 13, 15, 17 Type: closed, with ventilation facilities; Type code: 50 to 53 Type: open top. This standard does not involve requirements for ventilation and ventilation facilities. Requirements for relevant markings are specified in GB/T 1836-1997.


Some standard content:

1cs 55. 180. 10
National Standard of the People's Republic of China
G5/T53382002
idt IS0 1496-1: 1990
Series 1 freight containers
Technical requirements and test methods
Part 1: General cargo containers for general purposes2002-01-08 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
Implementation on October 1, 2002
GB.T 5338—7002
TS Preface
2 Small size
Dimensions and ratings
3 Design requirements
Appendix A (Standard Appendix)
General case packaging of various sizes and specifications (Standard Appendix) Requirements for the structure of the packaging components (Standard Appendix)
Appendix D Appendix to the standard:
Appendix E (Standard Appendix)||tt| |Time record F (prompt record)
Length requirements of the abstract
Dimension requirements of the series
Domestic system
Reference
GB/T5338-2002
This standard can adopt IS014561:1998 Series 1 Technical requirements and test methods for containers Part 1: Passivation and its revised version I501456-1/Amrl.1:1993 and 1501.19%1/AmGB/T33819951AAA, 1AA, 1A1AX general plastic packaging technical conditions T test method. Six standards jGR/T2216:995 and G/T5338-13h main differences: 1. According to the national conditions at the time, the above national standards were selected as two international standards. This time, the same parts were merged and the international standard 150195/1 was adopted. 2-The technical content of this standard is based on the IS () 14/14/:/Ad.1. The rectification of 1AA and 11B containers has been added. At the same time, corresponding adjustments have been made in various relevant items: In addition, the original TS) 1476/1/Amd.2 and 1AAABB containers are adopted! 1R should be transferred to GB/321S1395 and GB/153-1995 for the requirements of similar devices. In addition to the lifting operation test, the container draft test 13 items, into 12 items. This standard also made some changes, the joint consumption of Appendix L will be changed to Appendix E, Appendix F is modified. The diagram is designed to make the word history clear. bzxz.net
Related standards of this standard, CB/T7303-198 Series 1: Container technical requirements for complete solution M (idt 150 1496-2: 1395):
GB 1583-19 Series 1: Requirements and test methods for end-type container for dry bulk cargoes (id1 is) 14s6-$:1ss5>:
G16561125 Series.: Platform, rack container technical requirements and test methods (id10196-515S1/11727-195 Series 1: Non-pressure lowering cargo box grid requirements and test methods 1113. Appendices A, C, D and E of this standard are sufficient to be called standard appendices, and Appendix F of the large standard is a reminder of the reduction of the
wood standard was proposed by the People's Republic of China and the Ministry of Transport. This standard is drafted by the National Dyeing and Sales Standardization Technical Committee of the Ministry of Transport, China National Standardization Corporation, China Classification Society and China Container Loading Industry Expo. The main drafters of this standard are: Xuan, Si Ji, Zhang Binghua, Ling Qiu, GBT321S was first published in October 1982, and revised for the first time in July 18th; C6/T5338J was published in 1985, and revised for the first time in July 1991: GB/T53382002 ISO The International Organization for Standardization (ISO) is a global standardization organization (15 member bodies) of various countries. The drafting of international standards is generally carried out through the establishment of technical committees. Each member body has the right to represent itself in technical conferences on topics of concern to it. Governments and non-governmental international organizations , and those with network relations also participate in the relevant work.
The draft international standards approved by each technical committee shall be circulated to the member institutes for approval before being adopted in the short-term meeting. According to the IS procedure, the international standards I) 11S6-1 and the collection of the collection: and the screening policy is from [S0/1C101/8C1 (Collective Technical Requirements/1st Technical Requirements Committee Document]
S011U51-99 149-115 (1461/l1:13 and S) 1496-1/Amd.18 replaces [1496-1: 4th edition, 1S) 1 4S series upper container technical requirements and type 2 general standard includes the following parts: Part 1: Applicable containers
Part 2: Specification containers
Part 3: Technical body, gas modified bed → cargo end container
Part 4: Non-pressurized low-pressure container
Part 5: Flat and group container
Appendix 4 E of this standard is the standard appendix, Appendix F of this standard is the appendix of the specification, 1 Specification
National Standard of the People's Republic of China
Series 1 Container
Technical requirements and test methods
Part 1 General purpose container
Seriesrrelght eontainersSpecification and testingPart : :General rargo controlsror general pwrpusesGB/T5338202
idt 1so 1496-1.1950
K#G32!9
GfT553S
This standard specifies a series of 1 general-purpose packaging boxes with sealed group, breathable, ventilated and top-mounted types and the requirements for packaging types. It is suitable for inter-city exchange and waterway, road, railway and their combined use. 1.2 This standard is for the requirements of 1 other types of packaging! Adhesive type
13,13,15
5n 53
11 1 153 0.0
Type has one hole
All are not included in this standard
Teaching reduction type
This standard does not specify the requirements for ventilation and ventilation facilities. 1.3tGR/T1R36-1 stipulates the requirements for relevant markings. 2 Cited standards
The provisions included in the following standards become the main text of this standard through reference in this standard. When this standard is issued, the versions shown are valid. All standard departments will revise and use the possibility of using the latest version of the following standards. G1 series 1 container classification, size and rated mass as6 case packing corner parts technical conditions (cg1s01151:1) 84kxRE-
C3/183615
case code, certification to private mark (i15) 6345:1995:--1 container name terms (csg::9)
3 definitions
[/Ting all applicable definitions are applicable to this standard 4 dimensions and rated values
4.1 external dimensions
The external dimensions and nominal values ​​of containers listed in this standard are as specified in (reference, 1413, the listed parts of the container should not exceed the external dimensions, the external height of the bulk container can be reduced, they are represented by AX, 1X, 1CA and 1DX respectively, the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China 2002-1-8 batch 200210 01 Implementation
2.2 Internal dimensions of the packaging should be as large as possible: GR/T 5338-- 2002
Type 2 group-type container with half-door, the minimum internal length, width and height shall comply with the provisions of 4.3: Type 2 container with half-door, the total internal length and width shall comply with the provisions of 1.3; Type 3 container with top and opening on the top, its minimum internal length and width shall comply with the provisions of 3.3: Type 1011 closed container with one door, its minimum internal length, height shall comply with the provisions of 4.3.
Type 3 flash-ventilated container, the minimum internal length, width and height shall comply with the provisions of 4.3. Small internal dimensions
15) The minimum internal dimensions of the container in Series 1 are as shown in the table. Night 2 should be small internal size
Special tour number
Slope minimum height
Sales packing box outside the world
IAll types of container boxes except 1TX and 4TX shall have the ability to carry loads only in the load transfer area of ​​the bottom structure. 5.3.2.1 For these types of container boxes, a certain number of points shall be considered and sufficient load transfer area (or flat bottom). The degree of transfer shall be based on the total load between the vehicle and the longitudinal fullness. The longitudinal beam limit of the vehicle shall be within the two 20m standard width groove areas shown in Figure B of the standard. 5.3.2.2 The plane formed by the bottom of the container shall be 12.5m below the bottom surface of the bottom corner of the container. Except for the side beams of the corners, no part of the door of the container box shall be on this surface. If the book strength board near the flat corner is used for carbon flash protection, the length of the box should be more than 550m from the new part, and no more than 170m along the width of the box, measured from the side of the bottom corner to the plane of the back of the strip. 5.3.2.3 For the lower side, do not consider the bottom and the load transmission of the transport vehicle. Only when operating according to 5, 5.1 and 5.2, 2, consider the lower side of the load without loading and unloading. 5.3.2.4 When the actual bottom beam is equal to or less than 1000ma (becomes a flat box bottom, it meets the requirements 5.2.2.5 When the bottom of the container is not flat, the requirements are as follows: 1.1mm (see Appendix 5.5.3.3 for requirements when the bottom is not flat. 3.4 is not otherwise specified. For 1) and 71X containers, the bottom flatness of the container structure is not specified. 53.4 type bundles are loaded in dynamic or static conditions. When the sum of the load straps and the load straps of the container is equal to 1.5, the deformation of any part of the bottom of the container is not less than the bottom flat (that is, the bottom is below the bottom e :
5.3.5 The design of the container shall be able to withstand all forces generated in the container during transportation, especially the force generated by the solid cargo.
5.4 For all types of containers with end structures (except for those with end structures 1 and above), when conducting transverse rigidity tests, the sum of the length changes of the two alignment lines caused by the transverse displacement of the common parts shall not exceed 60mm. 5.5 For all types of containers with end structures (except for those with end structures 1 and above), when conducting longitudinal rigidity tests, the length of the bottom shall not exceed 25m.
For containers with end structures 2 and above, when conducting longitudinal rigidity tests, the length of the bottom shall not exceed 25m.
For containers with end structures 3 and above, the length of the bottom shall not exceed 25m.
For containers with end structures 4 and above, the length of the bottom shall not exceed 25m. E.7 The specified opening width
Each container should have at least three doors in one penalty area, and the door should be as small as possible. 1A.11 and 1.) Type closed container (and should not have a single opening 1 whose size is equal to the folding surface of the container, in any case, its height should not be less than 214mm: the width should not be less than 26mm1A and CC plastic container (2 no opening its internal section is equal to the table, no matter what the height should not be less than 221mm width not less than 235m, 1AA11 type container: code 2 should have a single opening. In any case, its commercial width is not less than:
5.8 Select facilities
5. 8. 1 Double diameter
GB/T5338--2002
5.8.1.1 In order to make the empty container of 1.11CX, 1T>X for loading, a fork can be set. 1AAA, 1AA, 1A, 1AX. 1BBB.: BB.IB and IBX empty containers do not have forks. 5-8-1.2 According to the provisions of 5.8.1.【, for 1CX: and 1X type containers, a special fork can be set for empty containers: 5.8.1 .3 For any fork installed, its size requirements shall comply with the initial requirements of Lu Lu ((Attachment 1 of the Specification), and the bottom plate shall be evenly distributed so that the fork can be used as a donor on one side: the bottom plate does not need to occupy the east side of the container - only the fork near the two ends of the fork is required, that is, 5-82 position || tt || Liu 1AAA type container must be equipped with a mandatory fork; for 1AA1A and _AX type containers, position requirements can be set. The size requirements are shown in Appendix I (Standard Scenarios). In addition, the rest of the bottom structure of the container shall comply with the current requirements of 5.3. 5.8.3 Solid cargo loading
Use container to improve solid control, and determine the specific fullness test
6-1 General
All types of containers with specified design requirements shall be subjected to the tests listed in 2.13 according to their design operating conditions, unless otherwise specified. Although the individual tests shall be carried out in reverse order, if there are any integrated tests that are not in compliance with the standard or the results of the accompanying tests are not obtained, the tests may be carried out according to different numbers. However, the safety test (test 12) shall be carried out after each of the designated tests. 6.1. The symbol "\" indicates the test packing. -
support. - Rated positioning:
T-… body's own mass:
: state and mass, test requirements based on gravity "seat step:, 2 the above values ​​of
"teaching has \ (》-time table material, belonging to the material single slow concept: "that is, still "clua.ug inherited the concept of internal rotation, 6.1.? The total internal test end teaching still or loading uniform distribution 6.3 in: 1 also all the test I load and addition specified in the test are all lower than the requirements 6..4 customer test terms in the requirements of the size - see the following standards: 15) 146 has a fixed
t/: 1414
GB/-1es:
5-2 Test 1 Stacking test (referred to as stacking
6.2.1 General test
4 Test without full load under the condition of transportation on a two-sea ship, the load-bearing capacity of the stacking in the middle of the stack is shown in the given design
. The packing is placed in four positions: - half water pads, one at each bottom corner, the stack is aligned with the first piece, and the plane size H is the same as the first piece. The load inside the box is evenly distributed on the bottom plate, so that the sum of the ear and test loads is equal to 1.
The vertical force shall be applied to the four parts or the ends of the box first, and the test force shall be as shown in Table 3. The top corners of the box shall bear the specified forces. They shall be loaded through the specified corner parts or through the simulation parts with the same plane shape as GB/T533B-2002 (i.e., alternating external dimensions, design, cutting and the same side load). If simulation parts are used, their design must make the forces borne by the container in the test the same as when the real objects are used. Table 3 Stacking force values ​​
Ten-day construction test
Container expansion device types
JA, AA.IAAA
and 1AX
I6.ILB, ILBD ICC,IC and ICX, time: 762553,762 552,762 550,good for parts,test force,381275,381 275,test light,table,standard code source,92 (-36-,=0 83C,for various loading methods,the force should be the same and the change of force and the damage caused by the pin displacement should be reduced to the lowest sensitivity,each coin can or simulate parts are virtual in the front deviation,the direction is 25.4mm,the amount is 38mm.6.2.3,try to find,22 29
132 253
432 293
After the test, the frame should not have permanent deformation and deformation that affect the use of the frame. The frame should be able to withstand the requirements of loading and unloading.
6.3 Test 2 Preliminary lifting test (also called pre-lifting) 6 3.1 General
This test verifies the ability of all other components except type 1 and 1D components to withstand the lifting force from the top to the bottom of the frame. The lifting force direction of 1I and 1DX components should be from the top to the bottom and horizontal to the bottom. This is the only way to lift the top corner of this type of installation. The test is also used to verify the ability of the bottom plate and the landing structure of the component to withstand the various forces generated by the accelerated operation when the load is removed from the box.
6.3.2 The load should be evenly distributed on the container. The total load should be equal to 2K. Then, the lifting force should be uniform from the four top corners to avoid obvious transfer or deceleration. The lifting force of each type of container should be uniform. The container should be lifted vertically and then placed on the ground. 6.3.3 Requirements
After the test, the container should not have any permanent deformation caused by pressure. It can meet the requirements of loading and unloading, consolidation and reloading operations.
6.4 Test: The test case is called bottom lifting) 5.4.1 General provisions
The test is to verify the ability of the load-bearing parts to be lifted by a pressure lifter at the bottom and supported by a pole centered above the box top.
6.4.2 The boxes shall be cut and distributed on the bottom plate factory, and the sum of the test load and the test load shall be equal to 2R. For the hall, when the four bottom corner pieces of the flat pool are drawn in the opposite direction, there will be no obvious confusion or deceleration in the circle: the angle between the line of action of the guide force and the actual angle of the corner piece is as follows: 5
Gn/T5338-2002
1AAA, 1AA.A and IAXR to R box 3
11K, 1BB, IB[1X type box 37°;
C, CKX type box 45°
1) X type box 60\:
In any standard product, the distance between the line of action of the guide force and the outer surface of the corner piece should not be greater than 38mn. Lifting without, should make the currency soldiers and individual parts to bear
container total hoist mia, then the parts back to the ground 6.4.3 bad water
teeth after the test, the case loading flow appears permanent deformation and abnormality that affects normal use, its size, can still be fully light lift, solid screening and recovery load operation requirements,
5.5 flow test 1 numerical quality test type
6.5.1 general
this complete test size cold proof case loading under the condition of dynamic load, that is, in the equivalent of the old time, bear the longitudinal effect of the construction force
6. 5.2 side
Rong loading load evenly distributed on the 4 Xin board, its white electricity and type test load and the same Ding R. The management of the collection of a single version of the year will be selected in the creation of the main parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method 5.2.2.1 When 1.1X.1 or 1.1X.1 or 1.1X.1 is installed only for the test load per person on the test plate, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the test load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.2. The main box cutting cloth hooks are distributed in the bottom plate factory, and the sum of the annual and test load benefits is equal to 2R. In order to avoid the obvious confusion or deceleration of the four bottom corner pieces, the line of action of the guide force and the actual angle of the guide force are as follows: 5
Gn/T5338-2002
1AAA, 1AA.A and IAXR to R box 3
11K, 1BB, IB [1X type box 37°;
C, CKX type box 45°
1) X type box 60\:
In the standard price, the distance between the line of action of the guide force and the outer surface of the corner piece should not be greater than 38mn. Lifting without, should make the currency soldiers and individual parts to bear
container total hoist mia, then the parts back to the ground 6.4.3 bad water
teeth after the test, the case loading flow appears permanent deformation and abnormality that affects normal use, its size, can still be fully light lift, solid screening and recovery load operation requirements,
5.5 flow test 1 numerical quality test type
6.5.1 general
this complete test size cold proof case loading under the condition of dynamic load, that is, in the equivalent of the old time, bear the longitudinal effect of the construction force
6. 5.2 side
Rong loading load evenly distributed on the 4 Xin board, its white electricity and type test load and the same Ding R. The management of the collection of a single version of the year will be selected in the creation of the main parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method 5.2.2.1 When 1.1X.1 or 1.1X.1 or 1.1X.1 is installed only for the test load per person on the test plate, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the test load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.2. The main box cutting cloth hooks are distributed in the bottom plate factory, and the sum of the annual and test load benefits is equal to 2R. In order to avoid the obvious confusion or deceleration of the four bottom corner pieces, the line of action of the guide force and the actual angle of the guide force are as follows: 5
Gn/T5338-2002
1AAA, 1AA.A and IAXR to R box 3
11K, 1BB, IB [1X type box 37°;
C, CKX type box 45°
1) X type box 60\:
In the standard price, the distance between the line of action of the guide force and the outer surface of the corner piece should not be greater than 38mn. Lifting without, should make the currency soldiers and individual parts to bear
container total hoist mia, then the parts back to the ground 6.4.3 bad water
teeth after the test, the case loading flow appears permanent deformation and abnormality that affects normal use, its size, can still be fully light lift, solid screening and recovery load operation requirements,
5.5 flow test 1 numerical quality test type
6.5.1 general
this complete test size cold proof case loading under the condition of dynamic load, that is, in the equivalent of the old time, bear the longitudinal effect of the construction force
6. 5.2 side
Rong loading load evenly distributed on the 4 Xin board, its white electricity and type test load and the same Ding R. The management of the collection of a single version of the year will be selected in the creation of the main parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method
5.2.2.1 When 1.1X.1 or X is installed only for the test load per person on the central installation pin, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.1BB, IB[1X type package 37°;
C, CKX type package 45°
1) X type package 60\:
In any price range, the distance between the line of action of the product force and the outer surface of the corner piece should not be greater than 38mn. Lifting without, should make the currency soldiers and individual parts to bear
container total hoist mia, then the parts back to the ground 6.4.3 bad water
teeth after the test, the case loading flow appears permanent deformation and abnormality that affects normal use, its size, can still be fully light lift, solid screening and recovery load operation requirements,
5.5 flow test 1 numerical quality test type
6.5.1 general
this complete test size cold proof case loading under the condition of dynamic load, that is, in the equivalent of the old time, bear the longitudinal effect of the construction force
6. 5.2 side
Rong loading load evenly distributed on the 4 Xin board, its white electricity and type test load and the same Ding R. The management of the collection of a single version of the year will be selected in the creation of the main parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method 5.2.2.1 When 1.1X.1 or 1.1X.1 or 1.1X.1 is installed only for the test load per person on the test plate, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the test load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.1BB, IB[1X type package 37°;
C, CKX type package 45°
1) X type package 60\:
In any price range, the distance between the line of action of the product force and the outer surface of the corner piece should not be greater than 38mn. Lifting without, should make the currency soldiers and individual parts to bear
container total hoist mia, then the parts back to the ground 6.4.3 bad water
teeth after the test, the case loading flow appears permanent deformation and abnormality that affects normal use, its size, can still be fully light lift, solid screening and recovery load operation requirements,
5.5 flow test 1 numerical quality test type
6.5.1 general
this complete test size cold proof case loading under the condition of dynamic load, that is, in the equivalent of the old time, bear the longitudinal effect of the construction force
6. 5.2 side
Rong loading load evenly distributed on the 4 Xin board, its white electricity and type test load and the same Ding R. The management of the collection of a single version of the year will be selected in the creation of the main parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method 5.2.2.1 When 1.1X.1 or 1.1X.1 or 1.1X.1 is installed only for the test load per person on the test plate, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the test load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.1 General Principles
This product is a cold proof case. When the load is in the same condition as the load, it is subjected to the longitudinal reinforcement force.
6. 5. 2 The load reduction of the container is evenly distributed on the 4 boards, and the white electricity and the type of test load are recommended. The single version will be selected in the creation of the remaining parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be installed
6.9 Test 8 Bottom elasticity test! Referred to as box bottom 6.9.1 General
This test is sufficient to prove the ability of the bottom of the container to withstand the impact of the loading vehicle or similar equipment during the loading process.
6.9.2 Method
The test is carried out on a tire test vehicle with a load of 5460k (12900), i.e. 27cc per wheel! The contact point between the wheel and the bottom surface of the box should be within the range of 18mm and the wheel sleeve is 1ccmm. The contact area between each wheel and the bottom plate shall not exceed 142rm, the width of the wheel is 180m, and the wheelbase is 6>mm . The test is to make the two bottom panels of the vehicle move. At this time, the four bottom corner pieces are replaced on the same horizontal support, and the bottom structure is changed.
6.9.3 Requirements
After the test: the remaining equipment does not have any quality that affects the use of the belt, and the internal specifications are met.
5.10 Test list steel giant test (abbreviated as steel) 5.10.1 Summary
The test is to verify the ability of the type 1 and 1 type other than the type 1 to withstand the locking push and pull generated by the ship. 10.2 The single loading container is in a hollow state. Place its four corner pieces on four horizontal supports. Open the bottom hole to load the entire bottom to make it check the vertical state in the horizontal direction. The direction of adjustment is only for the same end of the single bottom of the corner piece. When the test is carried out, the normal force is applied. The instrument is set at the age of the adult. In the British standard, add 15 (337001) to each top corner piece at the same time. Apply the force in parallel with the container end and the end, and then apply the force in the opposite direction. The Beijing container is tested with the same end joint as the rigid needs: the end joint of the loading pin should not be tested on both sides. The allowable deformation of the test under non-full load shall refer to the provisions of 5.4. 6.10.3 Try to require
test! , the lower tray of the rack packaging is out of the shadow of the padding and the permanent deformation and recording of the health of the rack, and the small size of the packaging must not be vortexed, which is the requirement of the firm training and sensitive installation operation.
6 type test number rigid purchase guarantee number special
This experiment tests the type of packaging products other than Li 1. The production is standard for locking, pay attention to the ability, 6-11-2 method
Container cat treasure (1 state, put it in the same long flat support, through the fixed bone through the door case bottom ceremony in the same and tight place of the company batch quality stop case foil belt batch washing to the tax. The number of returns is set on the same transmission of the price of the item. .
On the unloaded side, apply a force of VI[, respectively, and apply the force to the bottom cushion structure and the side of the container, and then select the force to be applied to the bottom. If the two walls of the container are hot-loaded, only the south-wind retreat test is carried out: if the unloaded joints are not strong enough, the test should be carried out on both ends.
GBT533B-2007
The allowable deformation under full load test shall comply with the provisions of 5.6.11.3
After the test, the container should not have normal permanent deformation and shape, and the size can still meet the requirements of loading and unloading, solidity and reloading.
6.12 Test 1 Fork lifting test (fork lifting)
E. 12.1 6.12.2 Small method 5.2.2.1 When 1.1X.1 or 1.1X.1 or 1.1X.1 is installed only for the test load per person on the test plate, the sum of the self-load of the container and the test load is equal to 1.5, and the container is not lifted horizontally. The length of the person subjected to the test load should be 1m. , the required box should be lifted 5 meters above the ground and then lowered to the ground. 6.12.2.2 When there are no two forks in the 1,1 or 1x size box, the method listed in 6.1.2.1 can only be used for the test of the inner side of the fork, that is, the fork tines are called forks. In this case, the test load and the box body are equal to 65, otherwise, the effect of i.12.2.1.
6. 12.3 During the test, the packaging shall not have any permanent deformation or condition that may affect its use. The dimensions can still meet the requirements of installation, fixing and installation operation. 6.13 or test 12. Use tightness test. 6. 13.1 Method: For each replacement chain and weld of the packaging, a water spray test shall be carried out. The nozzle thickness shall be 17.mm, the diameter of the nozzle shall be 1GCkP (m water). The distance between the nozzle end and the surface of the packaging to be tested shall be maintained at 1.00mm. The spray pressure shall be mF1/. The water content of each weld shall be within the spray pressure of a single batch. 6.13.2 After the test, the packaging shall not leak.1 General Principles
This product is a cold proof case. When the load is in the same condition as the load, it is subjected to the longitudinal reinforcement force.
6. 5. 2 The load reduction of the container is evenly distributed on the 4 boards, and the white electricity and the type of test load are recommended. The single version will be selected in the creation of the remaining parts.
Through the two single-piece wear holes of the pin, the first half of the small male plus ten container pins F, first to the part, then the currency point implementation method 5.5.3 purple requirements
Proof development, the box will not appear permanent shape and condition that affect our normal use, Jianger can still meet the requirements of the installation, comfort and replacement operations,
6.6 End wall strength test (back end tight) 6.6.1 General
Proof the ability of the new container end wall to withstand the conditions listed in 1. 6.6.2 Method
One end of the box is closed and the box door is called, and each end is tested: if the front and rear ends are symmetrical, the test is carried out. In the box, add 0.4g of the cloth load to the ends, so that the box ends can deform by themselves. 6.6.3 After the test, the container shall not have any permanent deformation or abnormality, and the size shall still meet the requirements of the installation arrangement. 6.7 The side wall shall be tested (screened) 6.7.1 General This is to verify the ability of the container to withstand the various behaviors caused by the new voyage. 6.7.2 The side wall of the container shall be tested. If the two rows are evenly loaded, only one side may be tested in reverse. The uniformly distributed load on the wall of the container, the longitudinal noise and the sound energy of the same type of parts will be measured (represented by 53). The test should be carried out under the condition of installation damage. 6.7.3
After the trial acceptance, the case loading cabinet will not be affected! The water with permanent use of the whole shadow and abnormality, and the size can still be loaded and unloaded, called comprehensive profit operation requirements:
6.8 trial inspection, item end standard test (allowed to be called sticky item) (for the installed pre-vibration test) 6.8.1 General purchase
This test is a verification test of the acceptance of the operator when operating on the same surface: 6.8.2 square
GH/T 53382002
The load of 0kg6b) is evenly distributed on the thinnest part of the pre-slab and the area of ​​6×3:m is tested. 6.63
After the test, the box should not have any permanent deformation and abnormality that can cause it to be used, and it can still be loaded and unloaded even if it is small, and it is required to be
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.