JB/T 6022.1-1992 Technical Specifications for Voltage Regulators for Magneto Motors JB/T6022.1-1992 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T6022.1-1992
Voltage regulator for magneto
Technical conditions
Published on 1992-05-28
Implementation by the Ministry of Machinery and Electronics Industry of the People's Republic of China on 1993-01-01
Mechanical Industry Standard of the People's Republic of China
Voltage regulator for magneto
Technical conditions
Subject content and scope of application
JB/T6022.1-1992
This standard specifies the technical requirements, inspection rules, marking, packaging and storage of voltage regulator for magneto (hereinafter referred to as regulator). This standard applies to regulators for various types of magneto (except aviation). 2 Reference standards
GB2828
JB/T6022.2
3 Technical requirements
Batch inspection counting sampling procedures and sampling tables (applicable to continuous batch inspection) Test methods for voltage regulators for magnetic motors
The regulator shall comply with the requirements of this standard and shall be manufactured in accordance with the drawings and technical documents approved by the prescribed procedures. 3.2 The regulator shall be able to operate normally under the following environmental conditions: a. The ambient medium temperature is -40~+80℃;
b. The relative humidity is not more than 95%;
The average atmospheric pressure is 86~106kPa.
The regulator shall be able to withstand the vibration and impact specified in Table 1. Table 1
Vibration frequency
Maximum acceleration (deceleration)
Vibration direction
X, Y, Z
Each direction
Vibration time
Note: For products that require frequency sweep vibration, the specific requirements shall be agreed upon by the supply and demand parties. 3.4 Requirements for the appearance and installation dimensions of the regulator Impact pulse width
a. The shell should be uniform in color and should not have obvious defects such as pores and cracks. Impact
Maximum acceleration
Number of impacts
b. The package should be intact and smooth, without pores, cracks and sagging of the encapsulant. The bonding of each lead pin (wire) should be reliable and the contact with the socket (or plug) should be good.
c. The installation dimensions should meet the requirements of the drawings.
3.5 Voltage regulation performance of the regulator
When the regulator works with the magneto, its voltage regulation performance shall comply with the provisions of Table 2. 3.6 The regulator shall be able to withstand 5 cycles of temperature shock test at -40℃ and 80℃, each for 1h. 3.7 The regulator shall work continuously for 3min at 1.2 times the maximum speed of the magneto without damage. Approved by the Ministry of Machinery and Electronics Industry on May 28, 1992 and implemented on January 1, 1993
The regulator shall be able to work normally after 24h of water spraying. Nominal
JB/T6022.1-1992
Minimum voltage regulation speed
Test conditions
Rated load
Note: Products with special requirements for voltage regulation performance can be negotiated with users. Durability of regulator
Maximum speed
≤7.4~8.2
≤14.8~16.4
Test conditions
Minimum load specified
Continuous operation for 100h at ambient medium temperature of 65±2℃ and 80% of the maximum speed of the magneto. 4 Test method
Test method see JB/T6022.2.
5 Inspection rules
5.1 Product inspection type
5.1.1 Factory inspection
Products are inspected according to the following factory inspection items and are allowed to leave the factory only after they are qualified. a. Appearance and installation dimension inspection;
b. Voltage regulation performance inspection.
5.1.2 Type inspection
5.1.2.1 The manufacturer shall conduct type inspection in one of the following situations. If the type inspection is not conducted or the inspection fails, the product shall not be put into production. a. The new product is finalized;
b. When the product is improved, modified or the process or raw materials are significantly changed; c. When the product is transferred to another factory for production or the production is resumed after a break of more than one year; d. When batch-produced products should be inspected regularly, not less than once every two years; e. When the national quality supervision and inspection agency proposes a requirement for type inspection. 5.1.2.2 Products for type inspection shall be randomly selected from the same batch of products that have passed the factory inspection, and the number of samples each time shall not be less than 6. First, test according to the factory inspection items, and after passing, divide the samples into two groups and conduct the following tests respectively: a. One group of samples undergoes vibration and impact test (sweep frequency test), high temperature test, low temperature test, damp heat test, temperature shock test, overspeed test and water spray test;
b. One group of samples undergoes durability test.
5.1.2.3 The type inspection of the product must all meet the specified requirements. If any item fails, double the number of samples should be re-drawn for re-inspection of the unqualified item; if it still fails, the batch of products shall be considered unqualified. 5.1.2.4 Products are allowed to be tested for all items without grouping, and the number of samples shall not be less than 3. 5.1.2.5 For products produced in batches or in large quantities, the number of durability test samples shall not be less than 2. 5.2 Acceptance rules
5.2.1 Product acceptance shall be carried out in accordance with the method specified in GB2828, and the specific inspection plan shall be agreed upon by the supply and demand parties. 2
JB/T 6022.11992
2With the consent of both parties, users can also accept the products according to the factory inspection items. During the acceptance, 2%5. 2. 2
(but not less than 6 pieces) of each batch of products submitted shall be selected for inspection. If any item is found to be unqualified, double the number of samples shall be drawn for re-inspection of the unqualified item; if there are still unqualified items, the batch of products shall be considered unqualified. 6
Marking, packaging, storage
6.1 The product shall be marked with the manufacturer's name and trademark in a conspicuous position. The product packaging box shall be marked with:
Manufacturer's name and trademark;
b. Product name;
Quantity;
d. Factory date: year and month.
The packaging box shall be firm, the box shall be lined with moisture-proof material, and the product shall not move in the box. The outer surface of the packaging box should be marked with:
a. Manufacturer's name and address;
b. Product name and model;
c. Factory date: year and month;
d. Volume: length × width × height, mm;
e. Gross weight, net weight, kg;
f. Quantity;
g. Shipping address and consignee;
h. "Handle with care", "Moisture-proof".
6.5 The technical documents supplied with the product include: a. Packing list;
b. Product factory certificate;
c. Operation and maintenance instructions.
6.6 The product should be stored indoors with an ambient temperature of 0~40℃ and a relative humidity of no more than 80%. The indoor air should not contain harmful substances that corrode the product.
6.7 The storage period of the product is two years (from the date of leaving the factory). The product should still comply with the provisions of this standard within two years. Additional remarks:
This standard was proposed and managed by Tianjin Internal Combustion Engine Research Institute. This standard was drafted by Tianjin Internal Combustion Engine Research Institute. The main drafter of this standard is Li Jixian. bzxZ.net
People's Republic of China
Mechanical Industry Standard
Voltage Regulator for Magnetron
Technical Article
JB/T 6022.1-1992
Published and issued by the China Academy of Mechanical Science
Printed by the China Academy of Mechanical Science
(No. 2 Shouti South Road, Beijing
Postal Code 100044)
Sheet 1/2
Format 880×1230
Word Count 6,000
First Edition in October 1992
First Printing in October 1992
Print Quantity 1-500
Price 1.60 Yuan
Mechanical Industry Standard Service Network: http://www.JB.ac.cn66_209
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.