Some standard content:
TCS 85.060
Classification number: Y32
Registration number: 15744-2005
Light Industry Standard of the People's Republic of China
QB/T2692-2005
Administered by QA/T35191999Www.bzxZ.net
110kV~330kV High Voltage Cable Paper
110kV.330kV High Voltage Cable Paper2005-03-19 Issued
National Development and Reform Commission of the People's Republic of China 2005-09-01 Implementation
This standard is listed in Q 8/13519-1999.11--330kV commercial cable grade standard QB/I2692-2005
This standard is based on the two standards of 01645-1989 110kV500kV universal cable technology system, which is non-equivalent.
This standard QR/T3514
1999 North pole: the main changes are as follows:
cancelled the 45μm type, added 50m and 163μm and the corresponding indicators: or the technical indicators such as tensile strength, length, intelligence, 1 frequency white wear, water-oil concentration and pH were reduced and modified: 4.) The document diagnosis of the volume was revised! The standard has been revised (Chapter 6): The simplified packaging has been revised in Chapter 7: The standard is recorded in Appendix A as a normative appendix. This standard is introduced by the China Light Industry Association. This standard belongs to the National Center for Standardization of Living Paper! The main standard is: Sichuan end-user company: This standard starts from: Shang Huajun.
The new generation of the temporary standard is released as follows: 2BY32018-1989,0B/13519-1999
4 The standard will be implemented from the beginning, replacing the original national light industry standard QB/35191999110-~330k frequency grade
110kv~330k high voltage cable paper
QH/T2692:2005
This standard specifies the outer category, requirements, test methods, sampling and marking, installation, transportation and use of [1kV~330kV high voltage power cable.
This standard applies to 110kV-330kV high-voltage power cables and common insulation devices. 2 Normative Reference Documents
The clauses in the listed documents become the clauses of this standard through the reference of this standard. The dated documents and all the amendments (excluding errata) or revisions are not applicable to this standard. However, the latest versions of these documents can be used if the parties reach an agreement based on this standard. For any citation without annotated date, the latest edition is not applicable to this standard: GB/450 Paper and paperboard reduction (GB/T450-2002, S0186: 1994) GBT451.1 Determination of the length and skewness of low-profile boards (GB/T451.2) Determination of the basis weight of low-profile boards (OB/T451.2-2002, S0536: 1995) GBT451.3 Determination of the thickness of low-profile boards (CB/T451.32002: idt1S0534: 1988) GB453 Determination of the thickness of paper and paper sheets (Constant speed addition method) (GB/453-202, idt1S01924-1: 1992) GB455 Paper and paper thickness (GB/455-2002, S01974: 1990) HT458 Paper board air permeability test (B/45-2002, VS06362:194) GB/T462 Paper and paperboard moisture content (GB/T462-2003, ISO287:1985, M (3) Paper, paperboard and residues (or fractions> (900) (GR/T7422003. [S02144:1997 GB/T-742
GB/T154S.2 Paper, paperboard and pulp water extract pH value GB/T154S.2-2003, ISO6588:1981. MODG/2828.1 Counting sampling inspection procedure Part 1: Sampling for batch inspection according to quality limit (4QL) inspection (CB/T 2828.1-203,1SO 2859-):1999. 1DT: GB/T3333 Cable paper power frequency mountain wear test method (0B/3333-1999, egIC554-2:1977) G3334: Cable paper dielectric loss (bridge) test (Bridge) BT3334-1999, ne[EC554-2:1977>
0BT7976 Determination of electrical conductivity of green paper board extract (GHT7976-1987:130554:1976) GB/T10342 Packaging and standard cloud
GB/10739 Paper, paperboard and paper sample handling and acceptance standard (GB/T10739-2002, ISO187:1990
GB/T12914 Paper and paperboard tensile strength The main determination method is (continuous tension loss method) (GBF12914-1991, CAVESO1924-2:1985
3 Classification
3.110kV~330kV high voltage relay code is DL. 3.2110k--330kV commercial cable length is 50m, 65m: 751, 125m, 175mm vertical ~ product 3.3110kV~330kV high voltage power supply is a roll sheet: 1
QB/T26922005
4 To eliminate
4110-30k high voltage end% technical index according to the table 1 provisions or national regulations: Table 1
H business information
item Bay "including some
natural cost
ug/kg i
C+I2E.-50
50 ! 3. 9
GTL-135
! 125±7.0
t.8: -n.05
ri.o--un
AGDL175
4.2 low Lu is 680mm~730, the class is (6251mm, the difference is also in line with the square diameter and width. 410 micro should be used with 1 high-grade comb acid needle water slurry to increase the system of fiber group level, all kinds of flat. There should be no crotch three, broken sensitive, transparent point, new, sealed point, no luster and Taiwan light streak, unreleased red Viking, pull, control, various guide extension mixed and internal limit light hole limit, 4.4 mourning Xie should be neat, clean, should not have 11. The speed should be tight, the core should not be loose, and the age of the horse shape should not be too [5n Tooth length shall not exceed mm,
4.5 bacteria barrier tight once effective, each statistical number of failures shall not exceed 3, the award shall be clearly marked. 5 Test method
6.1 Test selection shall be carried out according to GB/T450: 5.2 Point wear treatment rent test concentration quasi-atmospheric conditions according to 10739 5.3 Confirmation according to /451.1 determination.
5.4 Degree B4S3 lubricity
5.5 Tight grinding core (R/T151.2 and GRT451. Determination 5.6 New Zhangqiang stock (1B453B12914, line GB/12914 tide 5.! Single throw /143 measurement:
Type table pull GB/T455 specified
penetration -5 according to GD/T458 determination
engineering items body electrical indication GB/T3333 same actual
1 individual quality report negative cut (report (/T4 determination: 5.12 holding report electrical rate GT706 determination
cement liquid pH according to GB/T1S452 inhibition.
point points G742 continent determination.
day will be separated from the rat in the test Appendix A,
text wide water price CB/T462 determination
6 draw block
QB/T2692—2005
6.1 with - The annual payment fee is paid once, but each time the supplier shall provide a certificate of production of 11kV--33V cable points, including the requirements of this standard, and the inquiry certificate shall be accompanied by a product inspection report, an annual inspection certificate, and a quality inspection certificate. 5.2 Counting and corresponding inspection of products shall be carried out according to GB/? 2828. "Core: This certificate is for the core of the car, the original acceptance limit (AQL): academic degree, one period of abandonment, one quality angle will be correct (AO-: other technical indicators, AQ-6.5. Sample inspection two paragraphs of the discount, the inspection level is the special media inspection level 5-2 (see Table 2). Table 2
General specification kidney secondary dynamic sample plan
2 -- 156
151·280
ball S-2
world must
6.3 Determination of acceptability
The sample quantity of the first batch ...
For marking, packaging, transportation, storage and transportation
7.1110×V.330V is on the phone and the packaging of GR10342 or 7.211kV330kV electric frequency paper is B342, listed below, 2.1110kV-550kVF paper needs to be packaged, 7g/m: above the hospital lake packaging concentration of 5.
QB/T2692—2005
7.2.? In the old paper roll, the corrugated paper should be folded around the paper and fixed on the paper roll with adhesive tape, and then fastened with a woven tape on the paper roll, and then a plastic shrink tape in the middle. 7.3 Transportation H should be transported using clean transportation tools with anti-vibration facilities, and H should not be transported together with explosive materials. 7.4 The product should be stored in a clean, non-contaminated environment. When transporting the product to the pile, the product should not be cut off from the bottom. The product should be loaded and unloaded with care. Appendix A (Specification) Determination of ion content in ash QB/T 2692--2005 Prepare the sample with acid, dilute it with water, and measure the concentration of ions in the water to determine the dead element content. A.2 Instrument - Digital Analytical Instrument. 4.2.2 Ion Concentrator: DWS-5I Reagent. A. 2. 3 Porcelain 4.2.4 Wet furnace. A.3 Reagents A.3.1 Hydrochloric acid 1 1):
A.3.2 Concentrated hydrochloric acid
A.3.3 Chemically pure sodium ion or standard sodium ion A.3.4 Optical water, Na* or concentrated sodium ion (less than 2×10 g/m..A4 Standard sodium ion Na*) solution Preparation of positioning solution, 4.1P.VA4 positioning solution
Weigh 1-21% chemically pure or standard sodium ion in the range of 250~300% and mix with pure water or standard water (Na* concentration less than 2×10 g/) (A.34) to obtain standard Na positioning solution (0.M01 01/.) That is, when the mass accuracy is 2.3x10e/ml. of Na solution) the solution should be placed in a plastic container. A.4.2pNa5 fixed solution
H transfer tube accurately absorbs pN4 rate solution A.4.1>50mL into 50Wm volume, use no clock kA.3.4) to convert the concentration to be Na fixed solution.
Preparation method Beiwei w-jump ionization year calculation. A.5 Test steps
Weigh 5 test portions under wind, convert to 0.00K1g, add water, and put the effective portion into a porcelain vortex. First low humidity carbonization, then put it into high temperature, At (575+25)℃, there is no black carbon. After cooling, add acid (1+12 (A.3.1) for a while, evaporate on the hot plate, then add hydrochloric acid (1+1)2 (A.3.1) and evaporate, and finally add concentrated hydrochloric acid (A.3.2) 2ml to evaporate. After cooling: dissolve part of the molten steel (A.3.4) in batches, transfer 250ml to a bottle, dilute to the scale. Use TwS1 type sodium concentration meter (A.2.2) to measure - first Ma4A.4. ") or pNa5 (4.4.2) fall limit forget, and at the same time do the concentration test.||tt ||A.6 Operation of DWs-51 sodium ion concentration meter ||A.7 Calculation of ion content in ash by direct formula (A.1) (mm.] × 100
Where:
% ion content, converted to mg/k:
% Na mass per thousand points (mg/k): ...]×100
Wherein:
the amount of pseudo-ions in the sample is converted into the mass of Na per thousand points (mg/k):
the absolute value of the sample is converted into 1g (mg per thousand points).]×100
Wherein:
the amount of pseudo-ions in the sample is converted into the mass of Na per thousand points (mg/k):
the absolute value of the sample is converted into 1g (mg per thousand points).
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.