This standard replaces GB13042-1998 "Packaging Container Aerosol Cans". This standard specifies the terminology, classification, materials, requirements, test methods, inspection rules, marking, packaging, transportation and storage of iron aerosol cans. This standard applies to aerosol cans with a diameter of 25.4mm and a volume not exceeding 1000ml, made of tinned (chromium) thin steel plates. Compared with GB13042-1998 "Packaging Container Aerosol Cans", this standard has the following major changes: - It clearly stipulates that the volume of aerosol cans should not be greater than 1000ml; - It cancels the classification method of Z type and Y type according to materials and changes to classification according to structure, shape and pressure resistance; - The printing quality requirements shall comply with the provisions of QB/T1877. - The average contact height requirement for the can mouth is cancelled; - The heat resistance test requirement is cancelled; - The deformation pressure and bursting pressure requirements are changed to two levels, ordinary cans and high-pressure cans; - Add compatibility requirements; - Add hygiene requirements. GB 13042-2008 Packaging Container Iron Aerosol Cans GB13042-2008 Standard Download Decompression Password: www.bzxz.net
This standard specifies the terminology, classification, materials, requirements, test methods, inspection rules, marking, packaging, transportation and storage of iron aerosol cans. This standard applies to aerosol cans made of tin (chrome) plated steel sheets with a diameter of 25.4mm and a volume not exceeding 1000mL.
Article 6.4 of this standard is a mandatory clause, and the rest are recommended clauses.
This standard replaces GB13042-1998 "Packaging Container Aerosol Cans".
Compared with GB13042-1998 "Packaging Container Aerosol Cans", the main changes of this standard are as follows:
---Specify that the volume of aerosol cans should not be greater than 1000mL;
---Cancel the classification method of Z type and Y type according to materials, and change to classification according to structure, shape and pressure resistance;
---Printing quality requirements shall comply with the provisions of QB/T1877.
---Cancel the requirement for the average contact height of the can mouth;
---Cancel the requirement for heat resistance test;
---The requirements for deformation pressure and bursting pressure are changed to two levels, ordinary cans and high-pressure cans;
---Add compatibility requirements;
---Add hygiene requirements.
This standard adopts the relevant provisions of ISO903:2000 (E) "Determination of terms, dimensions and capacity of light metal containers Part 3: Aerosol cans".
This standard is proposed by China Packaging Federation.
This standard is under the jurisdiction of National Packaging Standardization Technical Committee.
The drafting units of this standard are: Zhongshan Kaida Fine Chemical Co., Ltd., National Packaging Product Quality Supervision and Inspection Center (Guangzhou), Hangzhou COFCO Packaging Co., Ltd., Guangdong Laiya Chemical Co., Ltd., Hebei Jiamei Tinplate Can Co., Ltd., China Packaging Federation.
The main drafters of this standard are: Lu Ming, Cui Ruping, Feng Hui, Zhu Liping, Zhan Yan, Fan Zhilong, Ruan Shen.
The standards replaced by this standard are:
---GB13042-1991, GB13042-1998.
The clauses in the following documents become the clauses of this standard through reference in this standard. For all dated referenced documents, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any un-dated referenced documents, the latest version shall apply to this standard.
GB/T1720 Determination of adhesion of paint films
GB/T2520 Cold-rolled electro-tinned steel sheets (GB/T2520-2000, eqvISO11949:1995)
GB/T2828.1 Sampling procedures for inspection by attributes Part 1: Sampling plans for batch inspection indexed by acceptance quality limit (AQL) (GB/T2828,1-2003, ISO2859-1:1999, IDT)
GB/T6739 Determination of film hardness of paints and varnishes by pencil method (GB/T6739-2006, ISO15184:1998, IDT)
QB/T1877 Printed products on tinned (chrome) steel sheets for packaging and decoration
QB/T2763 Coated tin (or chrome) steel sheet

ICS 55.140
National Standard of the People's Republic of China
GB 13042--2008
Replaces GB130421998
Packaging containers
Iron aerosol cans
Packaging containers---Tinplate aerosol can2008-07-30 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
Standardization Administration of the People's Republic of China
2009-03-01Implementation
Article 6.4 of this standard is mandatory, and the rest are recommended. This standard replaces GB13042-1998 "Packaging Container Aerosol Cans". Compared with GB13042-1998 "Packaging Container Aerosol Cans", this standard has the following major changes: It clearly stipulates that the volume of aerosol cans should not be greater than 1000mL. - The classification method of Z type and Y type according to materials is cancelled. It is changed to classification according to structure, shape and pressure resistance performance; the printing quality requirements shall comply with the provisions of QB/T1877. The average contact height requirement for the can mouth is cancelled; the heat resistance test requirement is cancelled:
The deformation pressure and bursting pressure requirements are changed to two levels, ordinary cans and commercial pressure; - Compatibility requirements are added;
Hygiene requirements are added.
GB13042-2008
This standard adopts the relevant provisions of IS090-3: 2000 (E) "Determination of terms, dimensions and capacity of light metal containers Part 3: Aerosol cans".
This standard is proposed by the China Packaging Federation. This standard is issued by the National Technical Committee for Packaging Standardization. The drafting units of this standard are: Zhongshan Kaida Fine Chemical Co., Ltd., National Packaging Product Quality Supervision and Inspection Center (Guangzhou), Hangzhou COFCO Packaging Co., Ltd., Guangdong Laiya Chemical Co., Ltd., Hebei Jiamei Tin Can Co., Ltd., China Packaging Federation. The main drafters of this standard are: Lu Ming, Ru Ping, Ma Hui, Zhu Liping, Zhan Yan, Fan Zhilong, Ruan Shen. The standards replaced by this standard have been issued as follows: GB13042 --1991, GB13042-1998.1 Scope
Iron Aerosol Cans
Packaging Containers
CB 13042-—2008
This standard specifies the terminology, classification, materials, requirements, test methods, inspection rules, marking, packaging, transportation and storage of iron aerosol cans (hereinafter referred to as "aerosol cans").
This standard applies to aerosol cans with a diameter of 25.4mm and a volume not exceeding 1000mL, made of tinned () thin steel sheets. 2 Normative references
The clauses in the following documents become clauses of this standard through reference in this standard. For all referenced documents with a date of reference, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, the parties who reach an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For all undated referenced documents, the latest versions shall apply to this standard. G3/T1720 Determination of paint film adhesion
GB/T2520 Cold-rolled electrolytic tinned steel sheet (GB/T2520-2000, egVISO11949:1995) GB/T2828.1 Sampling inspection procedure by attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) retrieval (GB/T2828,1-2003,15O 2859-1:1999,IDT) GB/T6739 Paints and varnishes Determination of paint film hardness by pencil method (GB/T6739-2006,ISO15184:1998,IDT) QB/T1877 Packaging and decoration (chrome) plated steel sheet printed matter QB/T2763 Coated tinned (or chrome) steel sheet 3 Terms and definitions
The following terms and definitions apply to this standard. 3.1
Aerosol can
A disposable metal container for aerosol products. When in use, the aerosol product is sprayed out through the valve in a controlled form under the action of pre-pressure.
Tinplate aerosol canAerosol can made of tin (chromium) plated steel sheet. 3.3
Three-piece canThree-piece canAerosol can composed of a can body, a top cover and a bottom cover. 3.4
Two-piece canOne-piece canTt||Tt||Aerosol can composed of a can body and a top cover (or bottom cover). 3.5
Straight-body canStraight-body canAerosol can with constant diameters at the top and bottom of the can body. 3.6
Necked-in can
Aerosol cans with reduced diameters at the top and (or) bottom of the can body. GB13042—2008
4 Product classification and specifications
4.1 Classification
4.1.1 Aerosol cans are divided into three-piece cans and two-piece cans according to their structure. See Figure 1. a) Three-piece cans
Figure 1 Structure of iron aerosol cans
4.1.2 Aerosol cans are divided into straight cans and necked cans according to their shapes. See Figure 2 and Figure 3. Figure 2 Straight cans
Figure 3 Necked cans
4.1.3 Aerosol cans are divided into ordinary cans and high-pressure cans according to their pressure performance 4.2 Specifications
The diameter specifications of aerosol cans are shown in Table 1.
b) Two-piece cans
Note: Special specifications shall be negotiated by the supply and demand parties. Material
Can diameter specification
445, string 49, 952, 057, Yi 65
The performance of tin-plated steel sheet shall comply with the provisions of GB/T25205.1
The adhesion and impact resistance of tin-plated (or chromium) steel sheet shall comply with the provisions of QB/T2763,5.2
6 Requirements
6.1 Appearance qualitybZxz.net
6.1.1 The printing quality shall comply with the provisions of QB/T1877. GH13042—2008
Unit is mm
6.1.2 There shall be no cracks, obvious wrinkles, depressions and mechanical damage at the shrink collar of two-piece cans. The roll mouth of three-piece cans shall be smooth and shall not have wrinkles, cracks and deformation, and the weld shall be flat.
6.1.3 The can body shall be flat and free of rust. For cans with inner coating, the inner coating shall be uniform and shall not have protrusions and impurities. 6.2 Dimensions and deviations
The main dimensions and deviations of aerosol cans shall comply with the provisions of Table 2. Table 2 Dimensions and deviations
Outer diameter of can mouth
Inner diameter of can mouth
Contact height of mouth
6.3 Re-coating and coating quality
6.3.1 Integrity of weld re-coating: For aerosol cans with weld re-coating, there shall be no linear corrosion or intensive corrosion points after testing. 6.3.2 Adhesion of inner and outer coatings: not less than Grade 2 6.3.3 Hardness of outer coating: 22H,
6.4 Pressure resistance requirements
The pressure resistance performance requirements of aerosol cans shall comply with the provisions of Table 3. Table 3 Pressure resistance
Airtightness
Deformed Leli
Explosion pressure
Ordinary can
Gao Yulin
Note: If the product has special requirements for the aerosol pressure resistance, it shall be in accordance with the relevant product standards or agreed upon by the supply and demand parties. 6.5 Compatibility
The user shall conduct product compatibility tests on aerosol cans according to the different contents and confirm them. 6.6 Hygiene requirements
Aerosol cans used to hold food, cosmetics, and medicines shall comply with relevant national health regulations. Unit: MPa
Unit: MPa
Not leaking
Not deforming
Not breaking
GB13042—2008
7 Test methods
7.1 Appearance
Measure at a distance of 0.6 m under natural light or 10W light. 7.2 Dimension measurement
7.2.1 The inner diameter, outer diameter, and height of the can mouth shall be measured with a special go/no-go gauge or vernier caliper. 7.2.2 The contact height is measured with a contact height dial gauge, see Figure 4. 0.35
300 (measurement body)
Figure 4 Measurement of contact height
7.3 Weld patch coating integrity test
Immerse the weld patch coating tape of the sample tank in 20% copper sulfate (CuS0,·5HO) solution, remove it after 2in, rinse it with clean water and dry it, and observe whether there is wireless corrosion or intensive corrosion points within the patch coating range. Note: The test solution is prepared with analytical pure reagents and distilled water. 7.4 Internal and external coating adhesion test
Perform according to GB/T1720.
7.5 External coating hardness test
Perform according to GB/T 6739.
7.6 Airtight performance test
7.6.1 Instrument
Airtight water bath tester for aerosol cans.
7.6.2 Test method
Place the sample can on the water bath tester, immerse it in water, inflate it and pressurize it to U. 80 MPa~-0. 85 MPa, and observe whether there are bubbles in the entire can within 1 minute.
7.7 Deformation pressure and burst pressure determination
7.7.1 Instrument
Aerosol burst pressure determination instrument: pressure range 0 MPa～4.0 MPat. 7.7.2 Determination method
Fill the sample can with clean water, insert the sealing head, tighten it (clamp it), and then fill the can with water and pressurize it to gradually increase the specified value of the deformation pressure, keep it for 10 seconds, and observe whether the can has permanent deformation. Continue to increase the pressure to the specified value of the burst pressure, keep it for 10 seconds, and observe whether the can bursts. 0 Inspection rules
8.1 The number of shipments is a batch, and one aerosol can is a unit product. 8.2 Product inspection is divided into factory inspection and type inspection. Factory inspection must be carried out when the product is delivered. The inspection items are 6.1, 6.2, 6.3.1 and the airtight test in 6.4. The type inspection items are 6.1~6.4. 8.3 Type inspection should be carried out in the following cases. a) When the raw materials and processes are changed, it should be carried out once every six months during normal production: b) c) When the product is resumed after suspension; d) When the factory inspection results are significantly different from the last type inspection; when the national quality and technical supervision agency proposes the requirement for type inspection 8.4 Sampling plan GB13042—2008 In this standard, 6.1 and 6.2 shall be subject to the one-time sampling plan for regular belt inspection in GB/T2828.1, and 6.3.6.4 shall be subject to the one-time sampling plan for regular belt inspection. The judgment rules and defect classification are shown in Table 4.
Table 4 Judgment rules and defect classification
Appearance (6.1)
Size (6.2)
Weld repair integrity (6. 3,1)
Adhesion of inner and outer coatings (6.3.2)
Hardness of outer coating (6.3.3)
Airtightness (6.4)
Deformation pressure (6.4)
Burst pressure (6.4)
Judgment number dimension
Unqualified classification
Class C unqualified
Class B unqualified
Class B unqualified
Class 13 unqualified
Class B unqualified
Class A unqualified
Class A unqualified
Class A unqualified
The judgment number of the inspection level S-4 and the secondary sampling plan for normal inspection is shown in Table 5. Inspection level
Table 5 Inspection level S-4, normal inspection secondary sampling plan Batch/piece
15000 or less
10001~35000
35 001 With F
Sample size
The judgment number of inspection level S·3, normal inspection secondary sampling plan is shown in Table 6. Cumulative sample size
Table 6 Inspection level S-3, normal inspection secondary sampling plan Batch
Sample book
8.6.3 Inspection level S-2, normal inspection primary sampling is shown in Table 7. Cumulative sample
Acceptance quality limit (AQL)
Class C nonconformity
Class B nonconformity
GR13042—2008
Inspection level S-2, normal inspection one-time sampling plan table 7
Sample mother
Marking, packaging, transportation and purchase and storage
Class A nonconformity
9.1 Marking
Products shipped out of the factory should have the certificate of conformity, product name, specification, quantity, production period, manufacturer name and other marks. Ac
Class H nonconformity
Generally, corrugated boxes are used for packaging, and the products are arranged vertically, separated by cross cardboard, or packaged according to user requirements. 9.3 Transportation
When transporting, be light and careful, and it is strictly forbidden to throw, prevent collision, and avoid rain, sunlight and pollution. 9.4 Storage
The product should be stored in a well-ventilated, dry and clean place, avoid direct sunlight and heavy pressure is strictly prohibited. GB 13042-2008
People's Republic of China
National Standard
Packaging Container
Iron Aerosol Can
GB13042—2008
Published and distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website: www, spc. net. cn
Tel: 6852391668517548
Printed by Qinhuangdao Printing Factory of China Standards Press Distributed by Xinhua Bookstores in various places
Format: 880×1230 1/16
Printing sheet 0.75
Word count 13 thousand
2008 11th edition, 2008 11th printing, Book number: 155066·1-34428, Price: 14.00 yuan, If there is any printing error, the publishing center of our company will replace it, Copyright infringement will be investigated
Report phone: (010) 685335331 Marking
Products leaving the factory should have the certificate of conformity, product name, specification, quantity, production period, manufacturer name and other marks. Ac
Class H non-conforming
Generally, corrugated boxes are used for packaging, and products are arranged vertically, separated by cross cardboard, or packaged according to user requirements. 9.3 Transportation
When transporting, it should be lightly loaded and handled, and it is strictly forbidden to throw, prevent collision, avoid rain, sun exposure and pollution. 9.4 Storage
Products should be stored in ventilated, dry coal, and clean places, avoid direct sunlight, and it is strictly forbidden to press heavily. GB 13042-2008
People's Republic of China
National Standard
Packaging Container
Iron Aerosol Can
GB13042—2008
Published and Distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website: www.spc.net.cn
Tel: 6852391668517548
Printed by Qinhuangdao Printing Factory of China Standards Press Distributed by Xinhua Bookstores in various places
Format: 880×1230 1/16
Printing sheet 0.75
Word count 13 thousand
2008 11th edition, 2008 11th printing, Book number: 155066·1-34428, Price: 14.00 yuan, If there is any printing error, the publishing center of our company will replace it, Copyright infringement will be investigated
Report phone: (010) 685335331 Marking
Products leaving the factory should have the certificate of conformity, product name, specification, quantity, production period, manufacturer name and other marks. Ac
Class H non-conforming
Generally, corrugated boxes are used for packaging, and products are arranged vertically, separated by cross cardboard, or packaged according to user requirements. 9.3 Transportation
When transporting, it should be lightly loaded and handled, and it is strictly forbidden to throw, prevent collision, avoid rain, sun exposure and pollution. 9.4 Storage
Products should be stored in ventilated, dry coal, and clean places, avoid direct sunlight, and it is strictly forbidden to press heavily. GB 13042-2008
People's Republic of China
National Standard
Packaging Container
Iron Aerosol Can
GB13042—2008
Published and Distributed by China Standards Press
No. 16, Sanlihebei Street, Fuxingmenwai, Beijing
Postal Code: 100045
Website: www.spc.net.cn
Tel: 6852391668517548
Printed by Qinhuangdao Printing Factory of China Standards Press Distributed by Xinhua Bookstores in various places
Format: 880×1230 1/16
Printing sheet 0.75
Word count 13 thousand
2008 11th edition, 2008 11th printing, Book number: 155066·1-34428, Price: 14.00 yuan, If there is any printing error, the publishing center of our company will replace it, Copyright infringement will be investigated
Report phone: (010) 68533533
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.