GB/T 14361.2-1993 Marine fiber rope pulley iron shell pulley GB/T14361.2-1993 standard download decompression password: www.bzxz.net

iDC 629.12.014
National Standard of the People's Republic of China
GB/TT4361.1·~14361.2--93
Ships' blocks for fibre ropes1993-04-17Promulgatedbzxz.net
National Technical Supervision Bureau
1993-1201Implementation
National Standard of the People's Republic of China
Ships' blocks for fibre ropes
Iron blocks
Ships' hlocks fmr fibre ropeslron shell blgcks
1 Main body and general scope
GH/T 14361.2-93
This standard specifies the product classification, technical requirements and test methods of long-length iron blocks for ships. This standard applies to the single-shell iron-shell pulley (hereinafter referred to as pulley) used for lifting grain ships. 2 Product classification
2.1 Types and parameters are shown in Table 1.
Unit price Long ring economic pulley
Single piece purchase pulley
Single long belt rope ring pulley
Medium supply permitted belt teaching ring pulley
Happy river pulley
Happy long civilian belt ring pulley
Fast lifting groove belt ring pulley
Good long ring work pulley
Prohibited lifting pulley
Empty long ring rope ring pulley
Pan cake record burning belt tooth pulley
2.2 Specification type test basic size
An individual working load.kiN
2.7.1 T1G.11 The structural type and basic dimensions of the core dismantling pulley shall be in accordance with Figure 1 and Table 2. Approved by the State Administration of Technical Supervision on April 17, 1993 5. u
1993-12-01 Implementation
Applicable to shrink
Accumulated diameter
Balance fiber white science
Gn/T 14361.2-93
[—Long ring 2—Resistance film to—Filling body 11—Emotion wheel through parts 1—Analysis 6-Bone wheel shaft 17—Please refer to the mouth: 8—Hanging average
Note: The safety of the hanging work is three times free from the meaning of the meaning, d
2G 13
2.2.2T1CS, TG5 type pulley station configuration type machine size according to Figure 2 and difference 3TG
ICT1G type
33.00·13.80
Applicable engineer
Liaowei white list
GB/T 14361.2 93
T·CS$
1-length: 2-rigid account; 3-single 11-clean wheel assembly: 5-cup 6-sliding light shaft 7-open: each; 5-emperor's
hhg611
life, hanging crying work load is safe work load 2 transmission 1 yuan
2.2.3TC, T2G type disassembly sharing system average type and basic size delivery 3 benefit table 4.453e18
35.5,16.0
6. 667.13
6. 55 0. 35
11.1511.73
13.6uJ4,82
Rope
Push white brown
CBT94361.2.·93
1--Long ring 2--Figure burst world light body 14 phase wheel stop · oil Xuan 5-get absolute shot: 7-opening pin-rear about
TCST2GS type car structure type and basic size according to Figure 1 and Table 5.55
35. 5 14 c
-1- FB
Chu Chu Ying
Rope diameter
GB/T 14361.2 93
T?CS #
1-Day return: 2-Use: 3-Shell value: 4-Pulley block: 5-Drawer: 1-Pulley shaft: 7-Small daily pin: 8-Product about
T, the structural type and basic dimensions of TSG type attached car are according to the closed 5 and table. 213
Secondary:
Applicable
General
GB/T14361:7—93
1: Length: 2..Surface plate 3 smooth body 4 one wheel assembly 5 one oil cup live wheel - cotter pin No. 1 practice
2.2.6, T3CS.13GS type car tree type and basic wood size 1 according to Figure S and Table 71t
THCT type
Applicable
* Direct storage
Details:
2.3 Certification
GB/143 61.2-.93
1--Length: 2 Figure screw year: 3 one finished, please wheel sister single -, 6 have wheel axle: period: 6 number of
safe T load 4.0kV. Single cake long ring with cable ring registration car, car rIC54.UGB/T14561.2
3 Technical requirements
3.1 The village of low car elements shall be equipped according to the provisions of Table 8, 4,
Parts name
big, national embroidery non
clear research shaft
Boat Sa bottle parts
sliding body
love wheel seal cold
CB/I 14361.2-93
Light carbon steel
Gold steel structure valve
Light quality account
Interaction or use micro-shadow gold
Trend to create a company
3.2 The raw materials of the factory should have a cold certificate. 20
Q1400-18
HT2c0Z9Sng-6-3
ZQA16-2
Standardized science
GB599--88
GTG99BS
(+ 1.348 88
G 55?585 or G8117C6?
rFK117 -5?
3.3 The surface of parts should be smooth to remove burrs, cracks, rust and other defects that affect strength, and the outer sharp edges of parts should be smooth. 3.4 The machined surface of parts shall not have holes, pores, shrinkage and looseness, and the non-machined surface shall not have defects that affect strength. 3.5 The surface of general parts should be smooth, and there should be no burrs, cracks, rust and other defects that affect strength. They must be corrected after manufacturing. 3.6 The surface of parts should be sharpened and grease should be applied to the surface. 3.7 When installing the pulley, check whether the wheels, rings or hanging parts can rotate smoothly without jamming. 4 Test method
The pulley should be tested according to the test load and load specified in Table 9. Method for static load test, the load time of the test shall not be less than 5min:, after printing, check that the load-bearing parts shall not produce permanent deformation and any sinking. 15
Test method
Safety worker
Test room
Test environment method
Safety working load
Before the test
Test control
Safety working load cut-off
Test load
GH/T14361.2-93
TCSTIGS
T3CST3GS
5 Standard test regulations
GB/T 14361.293
Each economic vehicle shall be inspected by the manufacturer's product quality inspection department\safety standards and technical requirements. The product shall be shipped only after it has passed the inspection and verified by the relevant inspection department, and a product quality certificate shall be issued at the same time. 6 Marking, packaging, storage
6.1 Each research vehicle shall have a product label, which shall indicate the following contents. Product name;
h. Product marking
c. Safe working load:
d. Applicable fiber diameter:
e. Manufacturer name or certificate and manufacturing date, 6.2 Packaging and storage
Product packaging must be secure and moisture-proof, and can meet your requirements for long-distance transportation. The travel vehicle must be stored in a ventilated and dry place.
Additional instructions
This standard is proposed by China Shipbuilding Industry Corporation, and this standard is issued by Jiangnan Shipyard:
This standard is issued by Guangdong Chaoyang Energy Accessories! Jiangnan Shipyard! "Capital is the first. The main drafters of this standard are Xie Maocong, Zhou Qinting, Zhang Zilai, and Zhang Tianlu. 29
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.