title>DA/T 7-1992 Inline file racks - DA/T 7-1992 - Chinese standardNet - bzxz.net
Home > DA > DA/T 7-1992 Inline file racks
DA/T 7-1992 Inline file racks

Basic Information

Standard ID: DA/T 7-1992

Standard Name: Inline file racks

Chinese Name: 直列式档案密集架

Standard category:Archives Industry Standard (DA)

state:in force

Date of Release1992-07-20

Date of Implementation:1992-10-20

standard classification number

Standard ICS number:General, Terminology, Standardization, Documentation>>Informatics, Publishing>>01.140.20Informatics

Standard Classification Number:General>>Economy, Culture>>A14 Library, Archives, Documentation and Information Work

associated standards

Publication information

other information

Publishing department:State Archives Administration of the People's Republic of China

Introduction to standards:

DA/T 7-1992 Inline File Storage Racks DA/T7-1992 Standard Download Decompression Password: www.bzxz.net



Some standard content:

Industry Standard of the People's Republic of China
Inline File Compact Shelves
1 Subject Content and Scope of Application
DA/T 7
This standard specifies the model, specification and structure, technical requirements, test method, inspection specification, packaging, transportation and storage of inline file compact shelves.
This standard is applicable to the design, manufacture, inspection and acceptance of inline dynamic file compact shelves and inline electric file crane compact shelves (hereinafter referred to as simple manual compact shelves and electric curtain compact shelves). 2 Reference standards
Technical conditions for high-quality carbon structural steel
GB 699
Technical conditions for high-quality carbon structural steel sheetsGB 710
GB 711
GB 1720
GB 1804
GB 435Y
Technical conditions for high-quality plain structural steel hot-rolled steel sheetsDetermination of film adhesion
Tolerances and fitsLimit deviations of dimensions without tolerancesCarbon spring steel wire
Seamless steel pipes for structures
GB 8162
GB9439Grey iron castings
7RG51 035C'042 Various colors of alkyd enamel
ZBG51043A04-9 Midnight nitrogen drying enamel ZBG510951I06-19 Iron red, yellow epoxy ester primer HG2239H06? Iron red, zinc yellow, iron black epoxy ester primer 3 Terms
3.1 Manual compact rack
The compact rack driven by hand is called a dynamic compact rack. 3.2 Electric compact rack
The compact rack driven by electricity is called an electric compact rack. 3.3 Movable rack
The rack that can run on the track is called a movable rack (also called a standard rack). 3.4 Fixed rack
The rack that is fixed at the end or between the guide rails and cannot run is called a fixed rack. 3.5 Single-sided rack For each standard section of the rack, only one shelf can be placed on the same horizontal plane: the rack that can place objects on both sides is called a single-sided rack. 3.6 Double-sided rack For each standard section of the rack, two shelves can be placed side by side on the same horizontal plane, and the rack that can place objects on both sides is called a double-sided rack Approved by the State Archives Administration of the People's Republic of China on July 20, 1992 78 Implemented on October 20, 1992 4 Models, specifications and structural shapes 4.1 Model DA/T 7-92 Design serial number, 1.2, small specifications (expressed by the width of the movable rack) SZM represents dynamic dense rack. LDZM represents movable dense rack.
Marking example: The first design width of the dynamic collection rack szM50c-1 is 503mm. The first design width of the electric dense collection rack DZM 500 1 is 500mm.
Specifications (per standard card) According to Table 1,
Active English
Dense collection rack
Single-sided fixed head
Double-sided fixed rack
4.3 Structural form
4.3.1 Manual dense collection rack (as shown in Figure 1).
4.3.2 Automatic dense collection rack (as shown in Figure 2).
KAoNTKAca
2100~-2500×500× 5.c
2100~250000×%=
2100~-2500 X00X274
2105~2500X900X5c0
DA/T 7- 92
Total fixed frame
(the maximum
movement distance,
mxy-2p-1g + 4s
single solid is
0-57 - 0 :3
1-standard plate: 2-upper bottle ban handle: 4-waist pole: 5-lower side; 6: stop block; 7-soft road 8-door: 9-chassis; 10-judgment plate: n-standard section number by plate thickness single-sided national standard frame
DA/T 7-92
double inner standard frame
90J *t+ 2P4 1J + 48
activity music
1-label frame: 2-electric operation button and indicator light: manual operation handle; 4-power switch: 5-power indicator light and alarm display; 6-turnway; 7-safety lock: 8-door. 9-shelf, 1-stop block 11-bottom stop insurance plate; 12-lower test panel; 13-small waist plate; 14-upper side step KAoNTKAca
5-technical requirements
DA/I 792
Both dynamic compact shelving and electric compact shelving shall comply with this standard and be manufactured in accordance with the drawings and technical documents approved by the manufacturer. 5.1 Structure
5.1.1 Both dynamic and electric compact shelving are assembled and combined structures. Dynamic compact shelving is equipped with a set of manual operation mechanism; electric compact shelving is equipped with two sets of electric and manual transmission mechanisms. They are mainly composed of columns, shelves, pull plates, side panels, trays and other parts. 5.1.2 The shelves and hanging boards should be able to adjust the height in the vertical direction of the vertical pull plate. The spacing between the holes on the vertical plate is 5 mm1 . 5.1.3 The track shall be paved and the transmission mechanism shall be installed according to the regulations, including the installation of the reverse installation and the blocking device. 5.1.4 The track can be installed with expansion bolts or nails, flush with the pool surface. It can also be installed on the ground surface. 5.1.5 Anti-static devices shall be installed, and lighting shall be installed as needed. 5.2 Processing and manufacturing
5.2.1 All sheet metal parts and machined parts shall be treated with a primer after processing to ensure that there are no cracks or scratches. 5.2.2 All welded parts shall be welded firmly, with smooth and even marks. 5.3 Manufacturing tolerance
5.3.1 After each standard section is installed, the maximum tolerance of the external dimensions (length, width, height) is 2mm. 5.3.2 After each standard section is assembled, the gap between the side panel and the middle waist panel should be less than ? mm. 5-3. 3 After the track is installed, within any 1 m range, the horizontal difference shall not exceed 1 mm, the length shall not exceed 4 mm, and the water difference between the corresponding points of the tracks shall be 1 mm, the parallelism deviation between the two shoe tracks is 1.5mm5.3.4 The gap between the door braids is evenly spaced between 1 and 2mm. 5.3.5 The forging limit deviation of the unmarked dimensions of parts shall be in accordance with IT13~-14 in GB1804. 5.4 Materials
5.4.1 The raw materials for compact shelving shall comply with the requirements of Table 2. Table 2
Material name
Cold rolled steel plate and rewind
Seamless steel
GL8162
Surface coating materials for compact shelving shall comply with the provisions of Table 3
Various colors of amino enamel
Various colors of alkyd enamel
Iron red, zinc yellow, iron ore red, epoxy primer
Phosphating primer
Powder spraying
5.4.3 The thickness of steel plate used for compact shelving shall comply with the provisions of Table 1. 82
Material name
Hot-rolled plate
Steel
H06-19
GB 4357
G3 959
ZB G51 013
ZB G a
H 7239
ZPG51 5
5.5Surface treatment
DA/T 7—92
Steel calibration
5.5.1 Before coating, all parts should be cleaned, degreased, and derusted. Cutting plates, side plates and other important parts should be treated with grouping. 5.5.2 Standard parts and fasteners of the product should be oxidized or galvanized. 5.6 Appearance quality
5.6.1 The surface of each part and assembly of the dense rack should be smooth and neat, without any unevenness or protrusions. 5.6.2 The color should be consistent with the order requirements, and the color should be evenly polished and without any scratches before painting. 5.7 Transmission mechanism
The transmission mechanism should rotate smoothly and without any loss. 5.8 Changeability
The parts and assemblies of the product should be able to maintain a constant temperature. 5.9 The coating film adhesion should be able to meet the grade indicators specified in GB 1720. 5.10 Electrical performance of electric dense racks 5.10.1 The running speed of each row of active dense racks is 3.2~3.511/min. It should be stable during operation, and the average insulation resistance of the wire should not be less than 20M.
5.10.3 The rated voltage of the power grid is within the range of 380±20%V and 220±10%V, and the compact rack should be able to operate normally. 5.114 Dynamic compact racks
5.11.1 The electrical circuit must have a reliable short-circuit protection device. 5.11.2
A dynamic protection electrode should be installed at the bottom of each row of dynamic racks, and the rack should be stopped sensitively and reliably. 5.11.3 Each group is equipped with a safe lock. 5.11.1 For wires and original components that are prone to aging, they should be replaced after the service life + expiration. 5.12 Noise of electric compact shelving
During the operation of compact shelving without load, the noise level should not exceed A). 5.13 Performance requirements
5.13.1 Shelf load
Single board. 1 Uniform load 40kg. Maximum strength 3rm. After 24h of loading, there shall be no cracks and permanent deformation. 5.13.2 Full load
Manual loosening standard section (six-layer double-sided bundle) Under full load (each single-sided shelf is uniformly loaded with 3kg), the frame should not have obvious deformation, and the frame should not fall over. 5.13-3 Or heavy operation
Under full load, each row of compact shelving should run smoothly under manual or electric operation, and there should be no blocking. The manual lifting force of each section should not be greater than 12N. The manual shaking force of each compact shelving is: 12N×number of loose sections). 5.13.1 Heavy Stability
After being subjected to an external force of one twentieth of the total load (horizontal external force in two directions) for 103 times, the inclination caused by the removal of the external force frame shall not be greater than one percent of the total height. The support and the column shall not have obvious deformation. R3
KAoNTKAca
6 Test method
6.1 Shelf load test
DA/T 7--92
6.1.1 Place two plastic plates on the table, and place the tested shelf on the pad. The support point pressure ruler should be within 20mm1 (drawing 3)
, auxiliary fixed point
6.1.2 Change the midpoint position of the shelf to points, and record the cold position of the quick board
6.1.3 Load the shelf evenly to the rated load (the load-bearing capacity of a single board is 40kg), and measure the maximum deformation of the shelf after 24h. 6.1.4 Check whether there are cracks and permanent deformation when placing. 6.2 Full load test
6.2.1 Assemble two standard racks in a row.
6.2.2 Load each shelf to the rated load (the load of the single rack is 30kg). Place for 21 hours and observe whether the vertical frame has obvious deformation and tilt.
6.3 Load operation test
6.3.1 Use a row (-~5 standard racks) of compact racks to perform an operation test under the rated load. 6.3.2 Hang a dynamometer on the handle, stop it from rotating, and make the compact rack run. Record the reading of the dynamometer, that is, the force of the handle rotation and observe the operation.
6.4 Load stability test (as shown in the figure)
(US H0\)
Frame contact line
Y direction
Wire rope
DA/T /—92
6.4.1 Place the two standard sections of dense rack on the platform, load it according to the rated load, and conduct a stability test. 6.4.2 Place the wire rope at point A1, and bend it into a right angle along the X axis through the fixed agent wheel, and add a weight of one tenth of the total load (two standard hanging sections) at the end.
6.4.3, lift the weight bowl up and down (the load should not have any impact on the rack when descending), repeat 10 times, remove the weight bowl, and measure the inclination of the frame, which should meet the requirements of Article 5.13.4.
6.4.4 The protective wire rope is fixed at point B, and the wire rope is passed through the fixed pulley in the Y direction or at a right angle. The rope end is loaded with the full load (one tenth of the weight of the two standard sections>) and the test and measurement are carried out according to the method in Article 6.4.3. 6.5 Electric case collection rack energy test
6.5.1 Running speed test
Within 1m layer distance, the running speed of the compact rack is measured with a Chuansha meter. After repeated multiple times, the average value is taken. 6.5.2 Conductor insulation resistance test
Use 500V Megohmmeter is used to test the insulation resistance of the electric compact shelving conductor and the tracking line to the ground. 6.5.3 Safety plate safety operation test
During the operation of the electric compact shelving, randomly touch the safety plate and observe its stopping performance. 6.5.4 Safety lock reliability test
Lock the electric compact shelving in the compact position with the safety lock, and then perform electric and manual operation respectively to observe whether the compact shelving is running.
6.5.5 Noise test
Place a microphone around the running compact shelving Use, each measured surface vertical distance 1m, sound level meter human sound level measurement, 6.6 paint mold adhesion test
according to GB172C provisions.
Inspection regulations
for dynamic and electric intensive and evenly divided factory inspection and type test, inspection items see Table 5. Table 5
Processing
Manufacturing tolerance
Appearance
Transmission structure
Transformability
Paint film adhesion
Electric intensive rack Running continuity
Wire insulation group
Circuit short circuit and machine overload protection
Earth moving insurance plate
Safety lock
Pole weight
All depends on the weight of the load
Heavy operation
Determine
KAoNiKAca
Technical requirements and indicators
5.10.1
5.10.2
3.21.1
5. 1.2 Article
5. 11. 3 Article
5. 13.1 Article
5. 13. 2 Article
5-18.3 Tea
5.15.4 Article
7.1 Test
DA/T 7 -~ 92
7.1.1 Both manual and electric compact shelving must be inspected by the manufacturer's inspection department before they can leave the factory, and a product inspection certificate and instruction manual will be issued.
7.1.2 The inspection items for manual compact shelving are carried out according to the contents of serial numbers 1 to 5 in Table 5. 7.1.3 The inspection items for electric compact shelving are carried out according to the contents of serial numbers 1 to 57 to 12 in Table 5. 7.1.4 When manual and electric compact shelving are delivered, the ordering department has the right to conduct random inspections on the products. The number of random inspections is per group, and manual and electric compact shelving are all inspected according to the inspection items.
7.1.5 If the random inspection products meet the requirements of the manufacturer, they will be regarded as the quality of the batch of products; if there are any items that do not meet the requirements, they will be re-inspected twice. If the re-inspection is qualified, the batch of products will be regarded as qualified. If one item is still unqualified after the re-inspection, all the repaired pieces will be re-inspected. 7.2 Type inspection
7.2.1 The manual and electric compact shelving shall be subject to type inspection under the following conditions: new products to be trial-produced;
h, when the interval is more than half a day:
center. When the product has major political changes in materials, technology, design, etc.; d. When the continuous production is carried out, it shall be carried out not less than once a year. 7.2.2 The products to be type inspected shall be randomly collected from the qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 The items of type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for the manual compact shelving, and all the contents listed in Table 5 for the electric compact shelving.
B, marking, packaging, transportation and storage
B-1 marking
B.1.1 The side poles of the manual and electric compact shelving shall be equipped with signs. B.1.2 The following items should be indicated on the label: a. Product name and model: b. Marking of trademark: 8.2 Packaging 8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, deflectors, and matching boards must be packaged separately, and the packages must have pads, insulation, etc. The packaging boxes must be tightly packed and marked with "handle with care", "no personal loading", "prevent rain", etc. 8.3 Transportation During transportation, collisions should be avoided as much as possible to prevent rain and snow. 8.4 Storage The compact shelving shall not be stored in the open air, but should be placed in a well-ventilated warehouse or indoors. Additional instructions: This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Corporation.1 Heavy Stability
After being subjected to an external force of one twentieth of the total load (horizontal external force in two directions) for 103 times, the inclination caused by removing the external force frame shall not be greater than one percent of the total height. The support and the column shall not have obvious deformation. R3
KAoNTKAca
6 Test method
6.1 Shelf load test
DA/T 7--92
6.1.1 Place two plastic plates on the table, and place the tested shelf on the short pad. The pressure edge of the support point is within 20mm1 (drawing 3)
, auxiliary fixed point
6.1.2 Change the midpoint position of the shelf to the point, and record the cold position
6.1.3 Load the shelf evenly to the rated load (the load-bearing capacity of a single plate is 40kg), and measure the maximum deformation of the shelf after 24 hours. 6.1.4 Check whether there are cracks and permanent deformation when placing. 6.2 Full load test
6.2.1 Assemble two standard racks in a row.
6.2.2 Load each shelf to the rated load (the load of the single rack is 30kg). Place for 21 hours and observe whether the vertical frame has obvious deformation and tilt.
6.3 Load operation test
6.3.1 Use a row (-~5 standard racks) of compact racks to perform an operation test under the rated load. 6.3.2 Hang a dynamometer on the handle, stop it from rotating, and make the compact rack run. Record the reading of the dynamometer, that is, the force of the handle rotation and observe the operation.
6.4 Load stability test (as shown in the figure)
(US H0\)
Frame contact line
Y direction
Wire rope
DA/T /—92
6.4.1 Place the two standard sections of dense rack on the platform, load it according to the rated load, and conduct a stability test. 6.4.2 Place the wire rope at point A1, and bend it into a right angle along the X axis through the fixed agent wheel, and add a weight of one tenth of the total load (two standard hanging sections) at the end.
6.4.3, lift the weight bowl up and down (the load should not have any impact on the rack when descending), repeat 10 times, remove the weight bowl, and measure the inclination of the frame, which should meet the requirements of Article 5.13.4.
6.4.4 The protective wire rope is fixed at point B, and the wire rope is passed through the fixed pulley in the Y direction or at a right angle. The rope end is loaded with the full load (one tenth of the weight of the two standard sections>) and the test and measurement are carried out according to the method in Article 6.4.3. 6.5 Electric case collection rack energy test
6.5.1 Running speed test
Within 1m layer distance, the running speed of the compact rack is measured with a Chuansha meter. After repeated multiple times, the average value is taken. 6.5.2 Conductor insulation resistance test
Use 500V Megohmmeter is used to test the insulation resistance of the electric compact shelving conductor and the tracking line to the ground. 6.5.3 Safety plate safety operation test
During the operation of the electric compact shelving, randomly touch the safety plate and observe its stopping performance. 6.5.4 Safety lock reliability test
Lock the electric compact shelving in the compact position with the safety lock, and then perform electric and manual operation respectively to observe whether the compact shelving is running.
6.5.5 Noise test
Place a microphone around the running compact shelving Use, each measured surface vertical distance 1m, sound level meter human sound level measurement, 6.6 paint mold adhesion test
according to GB172C provisions.
Inspection regulations
for dynamic and electric intensive and evenly divided factory inspection and type test, inspection items see Table 5. Table 5
Processing
Manufacturing tolerance
Appearance
Transmission structure
Transformability
Paint film adhesion
Electric intensive rack Running continuity
Wire insulation group
Circuit short circuit and machine overload protection
Earth moving insurance plate
Safety lock
Pole weight
All depends on the weight of the load
Heavy operation
Determine
KAoNiKAca
Technical requirements and indicators
5.10.1
5.10.2
3.21.1
5. 1.2 Article
5. 11. 3 Article
5. 13.1 Article
5. 13. 2 Article
5-18.3 Tea
5.15.4 Article
7.1 Test
DA/T 7 -~ 92
7.1.1 Both manual and electric compact shelving must be inspected by the manufacturer's inspection department before they can leave the factory, and a product inspection certificate and instruction manual will be issued.
7.1.2 The inspection items for manual compact shelving are carried out according to the contents of serial numbers 1 to 5 in Table 5. 7.1.3 The inspection items for electric compact shelving are carried out according to the contents of serial numbers 1 to 57 to 12 in Table 5. 7.1.4 When manual and electric compact shelving are delivered, the ordering department has the right to conduct random inspections on the products. The number of random inspections is per group, and the manual and electric compact shelving are all inspected according to the inspection items.
7.1.5 If the random inspection products meet the requirements of the manufacturer, they will be regarded as the quality of the batch of products; if there are any items that do not meet the requirements, they will be re-inspected twice. If the re-inspection is qualified, the batch of products will be regarded as qualified. If there are still any items that fail to meet the requirements after the re-inspection, all the repaired pieces will be re-inspected. 7.2 Type inspection
7.2.1 The manual and electric compact shelving shall be subject to type inspection under the following conditions: new products to be trial-produced;
h, when the interval is more than half a day:
center. When the product has major political changes in materials, technology, design, etc.; d. When the continuous production is carried out, it shall be carried out not less than once a year. 7.2.2 The products to be type inspected shall be randomly collected from the qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 The items of type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for the manual compact shelving, and all the contents listed in Table 5 for the electric compact shelving.
B, marking, packaging, transportation and storage
B-1 marking
B.1.1 The side poles of the manual and electric compact shelving shall be equipped with signs. B.1.2 The following items should be indicated on the label: a. Product name and model: b. Marking of trademark: 8.2 Packaging 8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, deflectors, and matching boards must be packaged separately, and the packages must have pads, insulation, etc. The packaging boxes must be tightly packed and marked with "handle with care", "no personal loading", "prevent rain", etc. 8.3 Transportation During transportation, collisions should be avoided as much as possible to prevent rain and snow. 8.4 Storage The compact shelving shall not be stored in the open air, but should be placed in a well-ventilated warehouse or indoors. Additional instructions: This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Corporation.1 Heavy Stability
After being subjected to an external force of one twentieth of the total load (horizontal external force in two directions) for 103 times, the inclination caused by removing the external force frame shall not be greater than one percent of the total height. The support and the column shall not have obvious deformation. R3
KAoNTKAca
6 Test method
6.1 Shelf load test
DA/T 7--92
6.1.1 Place two plastic plates on the table, and place the tested shelf on the short pad. The pressure edge of the support point is within 20mm1 (drawing 3)
, auxiliary fixed point
6.1.2 Change the midpoint position of the shelf to the point, and record the cold position
6.1.3 Load the shelf evenly to the rated load (the load-bearing capacity of a single plate is 40kg), and measure the maximum deformation of the shelf after 24 hours. 6.1.4 Check whether there are cracks and permanent deformation when placing. 6.2 Full load test
6.2.1 Assemble two standard racks in a row.
6.2.2 Load each shelf to the rated load (the load of the single rack is 30kg). Place for 21 hours and observe whether the vertical frame has obvious deformation and tilt.
6.3 Load operation test
6.3.1 Use a row (-~5 standard racks) of compact racks to perform an operation test under the rated load. 6.3.2 Hang a dynamometer on the handle, stop it from rotating, and make the compact rack run. Record the reading of the dynamometer, that is, the force of the handle rotation and observe the operation.
6.4 Load stability test (as shown in the figure)
(US H0\)
Frame contact line
Y direction
Wire rope
DA/T /—92
6.4.1 Place the two standard sections of dense rack on the platform, load it according to the rated load, and conduct a stability test. 6.4.2 Place the wire rope at point A1, and bend it into a right angle along the X axis through the fixed agent wheel, and add a weight of one tenth of the total load (two standard hanging sections) at the end.
6.4.3, lift the weight bowl up and down (the load should not have any impact on the rack when descending), repeat 10 times, remove the weight bowl, and measure the inclination of the frame, which should meet the requirements of Article 5.13.4.
6.4.4 The protective wire rope is fixed at point B, and the wire rope is passed through the fixed pulley in the Y direction or at a right angle. The rope end is loaded with the full load (one tenth of the weight of the two standard sections>) and the test and measurement are carried out according to the method in Article 6.4.3. 6.5 Electric case collection rack energy test
6.5.1 Running speed test
Within 1m layer distance, the running speed of the compact rack is measured with a Chuansha meter. After repeated multiple times, the average value is taken. 6.5.2 Conductor insulation resistance test
Use 500V Megohmmeter is used to test the insulation resistance of the electric compact shelving conductor and the tracking line to the ground. 6.5.3 Safety plate safety operation test
During the operation of the electric compact shelving, randomly touch the safety plate and observe its stopping performance. 6.5.4 Safety lock reliability test
Lock the electric compact shelving in the compact position with the safety lock, and then perform electric and manual operation respectively to observe whether the compact shelving is running.
6.5.5 Noise test
Place a microphone around the running compact shelving Use, each measured surface vertical distance 1m, sound level meter human sound level measurement, 6.6 paint mold adhesion test
according to GB172C provisions.
Inspection regulations
for dynamic and electric intensive and evenly divided factory inspection and type test, inspection items see Table 5. Table 5
Processing
Manufacturing tolerance
Appearance
Transmission structure
Transformability
Paint film adhesion
Electric intensive rack Running continuity
Wire insulation group
Circuit short circuit and machine overload protection
Earth moving insurance plate
Safety lock
Pole weight
All depends on the weight of the load
Heavy operation
Determine
KAoNiKAca
Technical requirements and indicators
5.10.1
5.10.2
3.21.1
5. 1.2 Article
5. 11. 3 Article
5. 13.1 Article
5. 13. 2 Article
5-18.3 Tea
5.15.4 Article
7.1 Test
DA/T 7 -~ 92
7.1.1 Both manual and electric compact shelving must be inspected by the manufacturer's inspection department before they can leave the factory, and a product inspection certificate and instruction manual will be issued.
7.1.2 The inspection items for manual compact shelving are carried out according to the contents of serial numbers 1 to 5 in Table 5. 7.1.3 The inspection items for electric compact shelving are carried out according to the contents of serial numbers 1 to 57 to 12 in Table 5. 7.1.4 When manual and electric compact shelving are delivered, the ordering department has the right to conduct random inspections on the products. The number of random inspections is per group, and the manual and electric compact shelving are all inspected according to the inspection items.
7.1.5 If the random inspection products meet the requirements of the manufacturer, they will be regarded as the quality of the batch of products; if there are any items that do not meet the requirements, they will be re-inspected twice. If the re-inspection is qualified, the batch of products will be regarded as qualified. If there are still any items that fail to meet the requirements after the re-inspection, all the repaired pieces will be re-inspected. 7.2 Type inspection
7.2.1 The manual and electric compact shelving shall be subject to type inspection under the following conditions: new products to be trial-produced;
h, when the interval is more than half a day:
center. When the product has major political changes in materials, technology, design, etc.; d. When the continuous production is carried out, it shall be carried out not less than once a year. 7.2.2 The products to be type inspected shall be randomly collected from the qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 The items of type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for the manual compact shelving, and all the contents listed in Table 5 for the electric compact shelving.
B, marking, packaging, transportation and storage
B-1 marking
B.1.1 The side poles of the manual and electric compact shelving shall be equipped with signs. B.1.2 The following items should be indicated on the label: a. Product name and model: b. Marking of trademark: 8.2 Packaging 8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, deflectors, and matching boards must be packaged separately, and the packages must have pads, insulation, etc. The packaging boxes must be tightly packed and marked with "handle with care", "no personal loading", "prevent rain", etc. 8.3 Transportation During transportation, collisions should be avoided as much as possible to prevent rain and snow. 8.4 Storage The compact shelving shall not be stored in the open air, but should be placed in a well-ventilated warehouse or indoors. Additional instructions: This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Corporation.2 The wire rope is originally fixed at point A1, and is bent into a right angle along the X-axis through the fixed pulley, and the end is added with a total load (two standard hanging sections): one-tenth of the weight of the rack.
6.4.3, lift the weight bowl up and down (the load should not have any impact on the rack when descending), repeat 10 times, remove the weight bowl, and measure the inclination of the rack, which should comply with the provisions of Article 5.13.4.
6.4.4 The protective wire rope is fixed at point B, and the wire rope is passed through the fixed pulley or at a right angle in the Y direction, and the rope end is added with a total load (two standard sections> One-tenth of the weight of the rack) is tested and measured by the method of Article 6.4.3. 6.5 Electric case rack energy test
6.5.1 Running speed test
Within 1m layer distance, measure the running speed of the compact rack with a sand meter, and take the average value after repeated multiple times. 6.5.2 Wire insulation resistance test
Use 500V Megohmmeter is used to test the insulation resistance of the electric compact shelving conductor and the tracking line to the ground. 6.5.3 Safety plate safety operation test
During the operation of the electric compact shelving, randomly touch the safety plate and observe its stopping performance. 6.5.4 Safety lock reliability test
Lock the electric compact shelving in the compact position with the safety lock, and then perform electric and manual operation respectively to observe whether the compact shelving is running.
6.5.5 Noise test
Place a microphone around the running compact shelving Use, each measured surface vertical distance 1m, sound level meter human sound level measurement, 6.6 paint mold adhesion test
according to GB172C provisions.
Inspection regulations
for dynamic and electric intensive and evenly divided factory inspection and type test, inspection items see Table 5. Table 5
Processing
Manufacturing tolerance
Appearance
Transmission structure
Transformability
Paint film adhesion
Electric intensive rack Running continuity
Wire insulation group
Circuit short circuit and machine overload protection
Earth moving insurance plate
Safety lock
Pole weight
All depends on the weight of the load
Heavy operation
Determine
KAoNiKAca
Technical requirements and indicators
5.10.1
5.10.2
3.21.1
5. 1.2 Article
5. 11. 3 Article
5. 13.1 Article
5. 13. 2 Article
5-18.3 Tea
5.15.4 Article
7.1 Test
DA/T 7 -~ 92
7.1.1 Both manual and electric compact shelving must be inspected by the manufacturer's inspection department before they can leave the factory, and a product inspection certificate and instruction manual will be issued.
7.1.2 The inspection items for manual compact shelving are carried out according to the contents of serial numbers 1 to 5 in Table 5. 7.1.3 The inspection items for electric compact shelving are carried out according to the contents of serial numbers 1 to 57 to 12 in Table 5. 7.1.4 When manual and electric compact shelving are delivered, the ordering department has the right to conduct random inspections on the products. The number of random inspections is per group, and the manual and electric compact shelving are all inspected according to the inspection items.
7.1.5 If the random inspection products meet the requirements of the manufacturer, they will be regarded as the quality of the batch of products; if there are any items that do not meet the requirements, they will be re-inspected twice. If the re-inspection is qualified, the batch of products will be regarded as qualified. If there are still any items that fail to meet the requirements after the re-inspection, all the repaired pieces will be re-inspected. 7.2 Type inspection
7.2.1 The manual and electric compact shelving shall be subject to type inspection under the following conditions: new products to be trial-produced;
h, when the interval is more than half a day:
center. When the product has major political changes in materials, technology, design, etc.; d. When the continuous production is carried out, it shall be carried out not less than once a year. 7.2.2 The products to be type inspected shall be randomly collected from the qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 The items of type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for the manual compact shelving, and all the contents listed in Table 5 for the electric compact shelving.
B, marking, packaging, transportation and storage
B-1 marking
B.1.1 The side poles of the manual and electric compact shelving shall be equipped with signs. B.1.2 The following items should be indicated on the label: a. Product name and model: b. Marking of trademark: 8.2 Packaging 8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, deflectors, and matching boards must be packaged separately, and the packages must have pads, insulation, etc. The packaging boxes must be tightly packed and marked with "handle with care", "no personal loading", "prevent rain", etc. 8.3 Transportation During transportation, collisions should be avoided as much as possible to prevent rain and snow. 8.4 Storage The compact shelving shall not be stored in the open air, but should be placed in a well-ventilated warehouse or indoors. Additional instructions: This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Corporation.2 The wire rope is originally fixed at point A1, and is bent into a right angle along the X-axis through the fixed pulley, and the end is added with a total load (two standard hanging sections): one-tenth of the weight of the rack.
6.4.3, lift the weight bowl up and down (the load should not have any impact on the rack when descending), repeat 10 times, remove the weight bowl, and measure the inclination of the rack, which should comply with the provisions of Article 5.13.4.
6.4.4 The protective wire rope is fixed at point B, and the wire rope is passed through the fixed pulley or at a right angle in the Y direction, and the rope end is added with a total load (two standard sections> One-tenth of the weight of the rack) is tested and measured by the method of Article 6.4.3. 6.5 Electric case rack energy test
6.5.1 Running speed test
Within 1m layer distance, measure the running speed of the compact rack with a sand meter, and take the average value after repeated multiple times. 6.5.2 Wire insulation resistance test
Use 500V Megohmmeter is used to test the insulation resistance of the electric compact shelving conductor and the tracking line to the ground. 6.5.3 Safety plate safety operation test
During the operation of the electric compact shelving, randomly touch the safety plate and observe its stopping performance. 6.5.4 Safety lock reliability test
Lock the electric compact shelving in the compact position with the safety lock, and then perform electric and manual operation respectively to observe whether the compact shelving is running.
6.5.5 Noise test
Place a microphone around the running compact shelving Use, each measured surface vertical distance 1m, sound level meter human sound level measurement, 6.6 paint mold adhesion test
according to GB172C provisions.
Inspection regulations
for dynamic and electric intensive and evenly divided factory inspection and type test, inspection items see Table 5. Table 5
Processing
Manufacturing tolerance
Appearance
Transmission structure www.bzxz.net
Transformability
Paint film adhesion
Electric intensive rack Running continuity
Wire insulation group
Circuit short circuit and machine overload protection
Earth moving insurance plate
Safety lock
Pole weight
All depends on the weight of the load
Heavy operation
Determine
KAoNiKAca
Technical requirements and indicators
5.10.1
5.10.2
3.21.1
5. 1.2 Article
5. 11. 3 Article
5. 13.1 Article
5. 13. 2 Article
5-18.3 Tea
5.15.4 Article
7.1 Test
DA/T 7 -~ 92
7.1.1 Both manual and electric compact shelving must be inspected by the manufacturer's inspection department before they can leave the factory, and a product inspection certificate and instruction manual will be issued.
7.1.2 The inspection items for manual compact shelving are carried out according to the contents of serial numbers 1 to 5 in Table 5. 7.1.3 The inspection items for electric compact shelving are carried out according to the contents of serial numbers 1 to 57 to 12 in Table 5. 7.1.4 When manual and electric compact shelving are delivered, the ordering department has the right to conduct random inspections on the products. The number of random inspections is per group, and the manual and electric compact shelving are all inspected according to the inspection items.
7.1.5 If the random inspection products meet the requirements of the manufacturer, they will be regarded as the quality of the batch of products; if there are any items that do not meet the requirements, they will be re-inspected twice. If the re-inspection is qualified, the batch of products will be regarded as qualified. If there are still any items that fail to meet the requirements after the re-inspection, all the repaired pieces will be re-inspected. 7.2 Type inspection
7.2.1 The manual and electric compact shelving shall be subject to type inspection under the following conditions: new products to be trial-produced;
h, when the interval is more than half a day:
center. When the product has major political changes in materials, technology, design, etc.; d. When the continuous production is carried out, it shall be carried out not less than once a year. 7.2.2 The products to be type inspected shall be randomly collected from the qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 The items of type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for the manual compact shelving, and all the contents listed in Table 5 for the electric compact shelving.
B, marking, packaging, transportation and storage
B-1 marking
B.1.1 The side poles of the manual and electric compact shelving shall be equipped with signs. B.1.2 The following items should be indicated on the label: a. Product name and model: b. Marking of trademark: 8.2 Packaging 8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, deflectors, and matching boards must be packaged separately, and the packages must have pads, insulation, etc. The packaging boxes must be tightly packed and marked with "handle with care", "no personal loading", "prevent rain", etc. 8.3 Transportation During transportation, collisions should be avoided as much as possible to prevent rain and snow. 8.4 Storage The compact shelving shall not be stored in the open air, but should be placed in a well-ventilated warehouse or indoors. Additional instructions: This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Corporation.2 Products that have undergone type inspection shall be randomly collected from qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 Items for type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for manual compact racks and all the contents listed in Table 5 for electric compact racks.
B. Marking, packaging, transportation and storage
B-1 Marking
B.1.1 A label shall be installed on the side pole of manual and electric compact racks. B.1.2 The following items shall be indicated on the label:
a. Product name and model:
b. Trademark:
, brand name and product name. "Date.
8.2 Packaging
8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, shields, and matching plates must be packaged separately, and the boxes must have pads, insulation, etc. Fee Zha case, hold firmly, and annotate with words such as "handle with care", "no individual access", and "prevent rain". 8.3 Transportation
During transportation, try to avoid collision and prevent rain and snow. 8.4 Storage
Compact shelves must not be stored in the open air, but should be placed in a well-ventilated warehouse or indoor. Additional remarks:
This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Company.2 Products that have undergone type inspection shall be randomly collected from qualified products, and the number of samples shall be one-half of the number of samples to be inspected. 7.2.3 Items for type inspection shall be carried out in accordance with the contents of Table 5 No. 1~5, 13~-16 for manual compact racks and all the contents listed in Table 5 for electric compact racks.
B. Marking, packaging, transportation and storage
B-1 Marking
B.1.1 A label shall be installed on the side pole of manual and electric compact racks. B.1.2 The following items shall be indicated on the label:
a. Product name and model:
b. Trademark:
, brand name and product name. "Date.
8.2 Packaging
8.2.1 All parts and assemblies must be packaged separately to prevent collision and scratches. 8.2.2 Electrical components such as motors, shields, and matching plates must be packaged separately, and the boxes must have pads, insulation, etc. Fee Zha case, hold firmly, and annotate with words such as "handle with care", "no individual access", and "prevent rain". 8.3 Transportation
During transportation, try to avoid collision and prevent rain and snow. 8.4 Storage
Compact shelves must not be stored in the open air, but should be placed in a well-ventilated warehouse or indoor. Additional remarks:
This standard is issued by the State Archives Administration and Shenyang Archives Bureau. This standard is issued by Shenyang Aircraft Manufacturing Company.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.