title>HG/T 2051.4-1991 Glass-lined agitator Paddle agitator - HG/T 2051.4-1991 - Chinese standardNet - bzxz.net
Home > HG > HG/T 2051.4-1991 Glass-lined agitator Paddle agitator
HG/T 2051.4-1991 Glass-lined agitator Paddle agitator

Basic Information

Standard ID: HG/T 2051.4-1991

Standard Name: Glass-lined agitator Paddle agitator

Chinese Name: 搪玻璃搅拌器 桨式搅拌器

Standard category:Chemical industry standards (HG)

state:Abolished

Date of Release1991-07-06

Date of Implementation:1992-01-01

Date of Expiration:2008-04-01

standard classification number

Standard ICS number:Chemical Technology>>Chemical Equipment>>71.120.99 Other Chemical Equipment

Standard Classification Number:Chemical Industry>>Chemical Machinery and Equipment>>G94 Non-metallic Chemical Machinery and Equipment

associated standards

alternative situation:Replaces HG 5-280-1979; replaced by HG/T 2051.4-2007

Publication information

other information

Introduction to standards:

HG/T 2051.4-1991 Glass-lined agitator Paddle agitator HG/T2051.4-1991 Standard download decompression password: www.bzxz.net

Some standard content:

Chemical Industry Standard of the People's Republic of China
Glass Agitator
Paddle Agitator
1 Subject content and scope of application
HG/T2051.4-91
This standard specifies the type, basic parameters, main dimensions and technical requirements of glass paddle agitators used in glass mixing vessels. This standard applies to open glass stirring vessels with a nominal volume of 50L to 5000L and closed glass stirring vessels with a nominal volume of 2500L to 20000L, with a nominal pressure less than or equal to 1.0MPa, a medium temperature higher than -20°C and lower than 20°C, and a nominal speed of 80 and 125r/min.
2 Reference standards
GB8163 Seamless steel pipes for fluid transportation
ZBG94004 Technical conditions for glass equipmentWww.bzxZ.net
ZBG94007 Quality classification standard for glass equipment HG/T2052 Transmission device for glass equipment
Type, basic parameters and main dimensions
Type, basic parameters and main dimensions are shown in Figure 1 and Table 1.3.2 The shaft head of the stirring machine is divided into type I, type II and type III There are three types (Appendix A). Type I shaft head matches HG/T2052 Tang glass equipment transmission device type 1. Type II shaft head matches HG/T2052. Tang glass equipment transmission device type ⅡI machine matches Type III shaft head matches HG/T2052
(Appendix A) Tang glass equipment transmission device type Ⅲ. 3.3 Agitator shaft head connection type and size, Type I shaft head see Figure 2, Table 2, Type II shaft head see Figure 3, Table 3. Ear shaft head see Figure A1, Table A1. Type I shaft head is used for 50L to 5000L glass open stirring container and 2500L to 20000L Tang glass closed stirring container, Type II shaft head and Type III shaft head are used for 50L to 4000L sugar glass open stirring container and 2500L to 4000 sugar glass closed stirring container
People's Republic of China Chemical Approved by the Ministry of Education and Industry on July 6, 199150
Implemented on January 1, 1992
HG/2051.4-91
Nominal volume
Nominal diameter of container
L series S series
Stirring shaft
Nominal diameter
HG/T2051.4—91
25 ×48
30×60
50×94
95×860×115
Open type stirring
mixing container
Closed type stirring
mixing container
21232212
25302685
23102399
Type I Type II||tt| |Nominal volume
Nominal diameter of container
L series S series
Stirring shaft
Nominal diameter
HG/T2051.491
Continued table 1
95×860×115
110×1070×132
125x1076×153
1 40×1286×170
Open type stirring
mixing container
Closed type stirring
mixing container
Note: L series and S series represent slender and short and fat glass stirring container respectively. Structural type II
I type Shaft head structure and size
Nominal diameter of stirring shaft
Connecting shaft diameter
HGKT 2051.4
Figure: 2
Type 1 agitator shaft head dimensions
3.3.2Type Ⅱ shaft head structure and dimensions
Taper 1:10
(section angle rotated 90°)
Nominal diameter of agitator shaft
M30×2
M38×2
M48×2
M60×3
M64×3
HG/T2051.491
Type Ⅱ agitator shaft head dimensions
Marking example:
HG/T 2051.491
Standard number
Length of agitator (H)
Nominal diameter of agitator shaft (N)
Shaft head type (I, Ⅱ or Ⅲ)
Code for paddle agitator (J)
Product name (agitator)
Tang glass paddle agitator, shaft diameter dN is 40mm, length H is 1030mm, and shaft head type is Ⅱ. Mark:
Technical requirements for agitator JⅡ40-1030HG/T2051.4-914
4.1 The pipe used for the glass agitator is made of No. 10 or No. 15 steel and is inspected and accepted according to GB8163. 4.2 The manufacture, inspection and acceptance of the glass agitator shall be carried out in accordance with the requirements of ZBG94004. 4.3 The shaft head of the glass agitator must be finely processed after the glass is cut. The agitator used for packing seal must be straightened after the glass is cut, and the shaft end sealing section must be ground. The radial total runout of the agitator shaft sealing section must be calibrated. Less than or equal to 0.2mm, the radial runout of the lower end is less than 0.3%H (H is the distance from the measuring point to the straight rod at the upper end of the shaft) 4.4 The quality classification of sugar glass stirrers shall be in accordance with ZBG94007. 5 Packaging, transportation and storage
5.1 The sugar glass stirrer must be wrapped with soft materials and securely fixed in a wooden box. 5.2 Collisions must be avoided during moving and transportation, and the packaging box must not be inverted. 5.3 The product should be accompanied by a packing list, product certificate and product instruction manual. 5.4
The product should be stored indoors and is not allowed to be stored or stacked in the open air. HG/T2051.491
Appendix A
Type III shaft head of sugar glass agitator
(supplement)
A1 This standard is applicable to Type III shaft head of sugar glass agitator with nominal pressure less than or equal to 1.0MPa, medium temperature higher than -20℃ and lower than or equal to 200℃, and nominal speed of agitator of 80 and 125r/min. A2 This appendix specifies the types and main dimensions of the shaft head of type III agitator for 50L to 4000L glass open mixing vessels and 2500L to 4000L glass closed mixing vessels. A3 Type II shaft head type, basic parameters and dimensions are shown in Figure A1 and Table A1. A4 The relevant dimensions of the glass agitator with type II agitator shaft head are the same as those of the glass agitator with type I agitator shaft head, except for Table A1 of this appendix.
di-left
Taper 1:10
Nominal diameter of agitator shaft
Additional remarks:
HG/T2051
M39×3
M48×3
M76×4
This standard is proposed by China National Chemical Equipment Corporation. Dimensions of shaft head of type II agitator
This standard is under the jurisdiction of the National Technical Committee for Standardization of Glass Equipment. This standard was drafted by Shanghai Pharmaceutical Design Institute of the State Drug Administration, and the main drafters of this standard are Hua Qiuyuan, Li Yijun and Ding Wenbangfei.
From the date of implementation of this standard, the former Ministry of Chemical Industry standard HG5-28069 "Paddle agitator for glass equipment" will be used as
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.