Some standard content:
FZ/T 810032003
The permissible degree of color fastness to sleeping liquid in 3.12.5 of this standard is a mandatory provision, and 3.12.9 and 3.12.10 are mandatory provisions. This standard replaces FZ/T81003-1991 "Single Clothing for Boys, Girls and Children". This standard was revised with reference to the Japanese standard JISL4203-1992 "School Clothing". Compared with FZ/T81003-1991, the main changes of this standard are as follows: considering the improvement and enrichment of the clothing standard system, the name of the standard is changed to "Children's Clothing, School Clothing"; - Added technical requirements for school clothing; - Added some reference standards;
- Added the limit of formaldehyde content released by finished products, infant clothing (two years old and below) ≤ 20mg/kg, clothing that directly contacts the skin ≤ 75mg/kg, clothing that does not directly contact the skin ≤ 300mg/kg; Added the allowable pH value of finished products that directly contact the skin to 4.0~7.5, and the allowable pH value of finished products that do not directly contact the skin to 4.0~9.0;
- Added the provisions on the allowable color fastness of finished products to washing, dry cleaning, dry friction, wet friction, sweat, light and sleeping liquid; - Added the provisions on the allowable pilling of finished products; - Enriched and improved the content of defect judgment. Appendix A of this standard, "Test method for the degree of seam unseating", partially adopts the provisions of FZ/T20019-1999 "Test method for the degree of seam unseating of wool woven fabrics".
Appendix A and Appendix B of this standard are normative appendices. This standard is proposed by the China National Textile and Apparel Council. This standard is under the jurisdiction of the National Technical Committee for Clothing Standardization. This standard is drafted by the Shanghai Garment Research Institute, the National Garment Quality Supervision and Inspection Center (Shanghai), the National Garment Quality Supervision and Inspection Center (Tianjin), the Shanghai Garment, Shoes and Hats Business Industry Association, and the Beijing Garment Quality Supervision and Inspection Station 1. Zhejiang RYB Group and Shanghai Yaduo Garment Co., Ltd. participated in the drafting.
The main drafters of this standard are: Xu Jian, Xu Yunbao, Zhu Bingrong, Wang Shurong, Wu Shuzhen, Jiang Yanxiang, Qin Wei, Ye Xiandong, Zheng Yafang. The previous versions of the standards replaced by this standard are: GB2663-1981, FZ/T81003-1991. I
1 Scope
Children's clothing, school uniform
FZ/T 81003—2003
This standard specifies the requirements, inspection (test) methods, inspection classification rules, and all technical characteristics such as marking, packaging, transportation and storage of children's clothing and school uniform.
This standard applies to children's clothing and school uniform produced in batches using textile fabrics as raw materials. 2 Normative references
The clauses in the following documents become the clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, the parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB250 Grey Scale for Assessing Change of Color
GB251 Grey Scale for Assessing Staining
GB/T1335.1 Clothing Sizes Men
GB/T 1335. 2
GB/T 1335. 3
Clothing Sizes Women
Clothing Sizes Children
GB/T2660 Shirts
GB/T2662 Cotton Garments
GB/T 2910—1997
Textiles
Quantitative Chemical Analysis Methods for Two-Component Fiber Blends GB/T2911-1997 Textiles Quantitative Chemical Analysis Methods for Three-Component Fiber Blends GB/T 2912. 1-1998
GB/T 3920—1997
GB/T 3921—1997
GB/T 3922—1995
Textiles-Determination of formaldehyde-Part 1: Free and hydrolyzed formaldehyde (water extraction method)-Test for color fastness-Colour fastness to rubbing
Textiles
Textiles
Test for color fastness-Colour fastness to washing
Textiles-Test method for colour fastness to perspiration
GB/T 3923. 1--1997
GB/T 4802. 1-1997
Textiles
Textiles
Tensile properties of fabrics-Part 1: Determination of breaking strength and elongation at breaking
Test for pilling of fabrics-Circular locus method
GB5296.4 Instructions for use of consumer products
Instructions for use of textiles and clothing
GB/T 5711-1997
GB/T 7573—2002
GB/T 8427—1998
GB/T 8629 -2001
Textiles
Textiles
Textiles
Textiles
Down garments
GB/T 14272
GB/T 18886—2002
Tests for colour fastnessColour fastness to dry cleaning
Determination of pH value of aqueous extract
Gold Colour fastness to artificial light: Xenon arc shading
Tests for colour fastness
Household washing and drying procedures for testing
Textiles
Tests for colour fastness
Colour fastness to sleeping liquids
FZ/T 20019-1999
9Test method for the degree of seam unraveling of wool woven fabrics FZ/T80002Marking, packaging, transportation and storage of clothing FZ/T 80007.1-1999
FZ/T 80007.3—1999
Test method for peel strength of garments using adhesive interlining Test method for washing resistance of garments using adhesive interlining FZ/T 81003—2003
FZ/T81004One-piece dress, skirt suit
3Requirements
Instructions for use
Instructions for use shall be in accordance with the provisions of GB5296.4. 3.2 Type regulations
Type settings shall be selected in accordance with the provisions of GB/T1335.1~~1335.3. 3.2.1
3.2.2 The specifications of the main parts of the finished product shall be designed according to the relevant provisions of GB/T1335.1~1335.3. 3.3 Raw material regulations
3.3.1 Fabric
Select fabrics suitable for children's clothing and school uniforms according to relevant textile fabric standards. 3.3.2 Lining
Use lining materials that are suitable for the performance and color of the fabric used, except for special needs. 3.3.3 Accessories
3.3.3.1 Interlining
Use interlining suitable for the fabric used, and its shrinkage rate should be suitable for the fabric. 3.3.3.2 Sewing
Use sewing threads that are suitable for the quality of the fabric used, except for decorative threads. The button thread should be suitable for the color of the button. 3.3.3.3 Buttons, zippers and metal accessories
Buttons (excluding decoration), zippers and metal accessories suitable for the fabric used shall be used without defects. They shall not deform, discolor or rust after washing and ironing.
Label pinning
Label pinning line shall be consistent with the base color of the trademark. 3.4 Technical regulations for warp and weft yarns
The front body shall be warped in the same direction (inverted warping is not allowed), and the allowable degree of the back body, sleeves, front and back trousers shall be in accordance with the provisions of Table 1. Table 1
Superior products
Yarn-dyed or printed, striped and checked materials
3.5 Rules for stripes and checkers
3.5.1 Fabrics with obvious stripes and checkers of 1.0 cm or more shall be in accordance with the provisions of Table 2. Table 2
Pocket, pocket cover and front body
Rules for stripe and grid
First-class products
Qualified products
Stripes are aligned, grids are aligned horizontally, and the difference is not large. The size of the grids is inconsistent, and the front body is more than 0.3cm.
Stripes are aligned, grids are aligned horizontally, and the difference is not more than 0.3 cm.
Stripes are symmetrical from left to right, and the difference is not more than 0.3cm. The center of the front of the bag is the standard.
Yin and yang stripes are mainly obvious stripes.
Side seams of trousers
Front and rear crotch seams
Note: Special designs are not subject to this restriction.
Table 2 (continued)
Rules for stripe and grid
The sleeves are straight from left to right, the stripes are symmetrical, and the difference is not more than 0.5 cm.
10cm below the side seam pocket, the checkered material is aligned horizontally, and the difference between them is no more than 0.5cm.
The stripes are symmetrical, and the checkered material is aligned horizontally, and the difference between them is no more than 0.4cm.
3.5.2. For materials with reversed and straight fur (velvet) and yin-yang grid, the whole body should be in the same direction (for materials with long fur, the whole body should be in the same direction). 3.5.3 For fabrics with special patterns, the main pattern shall prevail, and the whole body should be in the same direction. 3.6.1 Splicing is not allowed for preschool children's clothing. The splicing of other children's clothing and student uniform parts is as follows: a)
Collar lining: avoid the shoulder seam, two joints and one splice.
Overcoat surface: avoid the eye position at the lower third of the coat surface, two joints and one splice. b)
Sleeves: single-piece sleeve splicing angle, no more than one-quarter of the sleeve circumference. c)
Waistband: only allowed at the back crotch seam of the pants.
3.6.2 Decorative splicing is excluded.
3.7 Color difference regulations
FZ/T 81003—2003
The color difference of the collar, pocket and body, and the side seam of the finished product is higher than level 4, and other surface parts are not lower than level 4. The color difference between the top and the trousers in the suit is not lower than level 4.
3.8 Appearance defect regulations
The defects of each part of the finished product shall be in accordance with the provisions of Table 3, and the division of each part is shown in Figure 1. Only one defect is allowed for each independent part. Defects not listed in this standard shall be implemented according to their form and refer to similar defects in Table 3. Public
FZ/T81003—2003
Point name
3 pieces thicker than twice the coarse yarn
4 pieces thicker than three times the coarse yarn
Granular coarse yarn
(oil, rust, color spots)
Sewing regulations
Needle density shall be as specified in Table 4.
Light and dark lines
Overlock
Handmade needle
Triangular needle
Part 1
Not allowed
Not allowed
Not allowedwww.bzxz.net
Not allowed
Allowed degree of existence in each part
Part 2
Length 1cm～3 cm
Not allowed
Not obvious
Not allowed
Does not affect the appearance
Does not affect the appearance
Needle density
3cm10～14 stitches
3cm not less than 9 stitches
3cm not less than 7 stitches
3cm not less than 5 stitches
1cm not less than 12 stitches
1 cm not less than 9 stitches
each hole not less than 8 threads
each hole not less than 4 threads
3rd part
3 cm～6 cm
less than 2.5cm in length
4cm in length, less than 1cm in width
does not affect the appearance
not more than 0.2 cm2
except for special needs
shoulder seam, sleeve ridge, collar not less than 9 stitches
calculated on one side
the height of the foot binding line should be consistent with the thickness of the stop
the seam of each part should not be less than 0.8cm. The sewing line should be straight, neat, flat and firm, and there should be a back stitch at the starting and ending needles. The collar should be straight, flat and the collar surface should be appropriately tight. The sleeves should be round and smooth, and the front and back of the sleeves should be basically the same.
The rolling strips and pressing strips should be flat and narrow.
The padding of the bag cloth should be folded or overlocked.
Both ends of the bag mouth should be firm, and the backstitch can be used with a bar tacking machine or a lockstitch machine. The sleeve suffs, sleeve seams, hem seams, bottom edges, cuffs, and the lining of the hanging noodles should be accurately positioned with the stitches and buttonholes of appropriate size, with the buttons and eyes aligned and neat and firm. The button feet should be of appropriate height and the thread knots should not be exposed. The trademark, size mark, ingredient mark and washing mark should be positioned correctly, clearly and accurately. There should be no two single jumps and continuous jumps within 30cm of the sewing stitches of each part of the finished product, and chain stitches are not allowed to jump. The limit deviation of specifications of the main parts of the finished product
The limit deviation of specifications of the main parts of the finished product shall be as specified in Table 5Table 5
Name of part
Allowable deviation
Unit is cm
Name of part
Total shoulder width
Appearance regulations after ironing
Table 5 (continued)
Raglan sleeves
3.11.1 All parts shall be ironed flat and neat, without yellowing, water stains, or gloss. 3.11.2 Degumming, glue seepage, and wrinkling are not allowed in the parts using adhesive interlining. 3. 12
Physical and chemical performance requirements
The shrinkage of the main parts of the finished product after dry cleaning shall be as specified in Table 6. Table 6
Name of part
The wrinkle difference of the finished product after dry cleaning shall be as specified in Table 7. 3. 12.2
Wrinkle difference after dry cleaning
Superior products
The shrinkage of the main parts of the finished product shall be as specified in Table 8. 3.12.3
Part name
Superior products
First-class products
The peel strength of the adhesive interlining part shall be ≥6N/(2.5cmX10cm). The allowable degree of color fastness shall be as specified in Table 9.
Dry cleaning resistance
Superior products
First-class products
Allowable deviation
FZ/T81003—2003
The unit is cm
±0.7(5·2 series)
Shrinkage after dry cleaning
The unit is grade
Qualified products
Qualified products
The unit is grade
Acceptable degree of color fastness
First-class products
Qualified products
FZ/T81003—2003
Dry friction resistance
Wet friction resistance
Perspiration resistance
Saliva resistance
(Infant and toddler clothing for two years old and below)
The allowable degree of pilling shall be as specified in Table 10. 3.12.6
Combed (suede)
Combed (glossy)
The degree of seam cracking in main parts shall be in accordance with the provisions of Table 11. Grade
Superior products
Superior products, qualified products
Table 9 (continued)
Superior products
Superior products
Permissible degree of color fastness
First-class products
Permissible degree of pilling
Unit: grade
Qualified products
Unit: grade
First-class products, qualified products
Unit: centimeter
Degree of slippage
The seam strength of the back crotch seam of trousers shall not be less than 140N/(5.0cmX10cm). 3.12.8
Limits on formaldehyde release in finished products: infant clothing (two years and below) ≤20mg/kg, clothing in direct contact with skin 3.12.9
≤75mg/kg, clothing in indirect contact with skin ≤300mg/kg. 3.12.10 The permissible pH value of finished products: 4.0~7.5 for products in direct contact with skin, 4.0~9.0 for products in indirect contact with skin.
The composition and content of raw materials used in finished products shall be consistent with the contents marked on the instructions for use. 3. 12. 11
3.13 Others
Technical requirements for shirts, dresses, skirt suits, down clothing, cotton clothing and other products in children's clothing and school uniforms shall be implemented in accordance with the corresponding product standards such as GB/T2660, FZ/T81004, GB/T14272, GB/T2662, etc. Technical provisions not mentioned in the above standards shall be implemented in accordance with the provisions of this standard. 4 Inspection (test) methods
4.1 Inspection tools
4.1.1 Steel tape measure.
4.1.2 Needle detector.
4.1.3 Grey scale for evaluating discoloration (GB250). 6
4.1.4 Grey scale for evaluating staining (GB251). 4.1.5 Sample photos of appearance defects of men's and women's single and cotton clothing and men's and women's and children's single clothing. 4.1.6 Sample photos of wrinkled appearance of men's suits.
4.1.7 Sample photos of appearance defects of men's and women's woolen clothing. FZ/T81003—2003
4.1.8 Pilling sample of worsted wool fabrics (velvet) (GB/T4802.11997), pilling sample of worsted wool fabrics (glossy) (GB/T4802.1—1997), pilling sample of carded wool fabrics (GB/T4802.1—1997). 4.2 Determination of finished product specifications
4.2.1 The specifications of the main parts of the finished product shall be in accordance with 3.2.2. 4.2.2 The measurement method of the main parts of the finished product shall be in accordance with Table 12 and Figure 2. The allowable deviation shall be in accordance with 3.10. Table 12
4.3 Appearance measurement
Part name
Total shoulder width
Raglan sleeve
Measurement method
Measure vertically from the highest point of the shoulder seam of the left front to the bottom edge, or measure vertically from the middle of the back collar to the bottom edge.
Button up (or close the zipper) and lay the front and back body flat, and measure horizontally along the bottom seam of the sleeve (calculated around the circumference).
Measure horizontally when the collar is laid flat, the upper opening of the stand-up collar and the lower opening of other collars (except for folding collars).
Measure horizontally from the intersection of the shoulder and sleeve seams.
Measure from the intersection of the shoulder and sleeve seams to the middle of the cuff. Measure from the middle of the back collar along the intersection of the shoulder and sleeve seams to the middle of the cuff. With the trouser hook (button) fastened, measure horizontally along the middle of the waist width (calculated around the circumference). Measure vertically from the upper opening of the waist along the side seam to the hem. FZ/T 81003---2003
The matching of finished products shall be in accordance with the provisions of 3.5.
4.3.2 When measuring the degree of color difference of finished products, the yarn direction of the measured parts must be consistent. Use northern sky light for illumination in the northern hemisphere and southern sky light for illumination in the southern hemisphere, or use an equivalent light source of 6001x or above. The incident light is about 45° to the fabric surface, and the observation direction is roughly perpendicular to the fabric surface. Visual inspection is performed at a distance of 60cm, and compared with the GB250 sample card in accordance with the provisions of 3.7. 4.3.3 The appearance defects of finished products shall be in accordance with the provisions of 3.8, and compared with the appearance defect samples of men's and women's single, cotton clothing and men's and women's and children's single clothing. 4.3.4 Sewing quality shall be in accordance with the provisions of 3.9. The stitch density shall be in accordance with the provisions of 3.9.1, and any 3cm of the finished product shall be measured (except for thick and thin parts). 4.3.5 Determination method of weft skew:
Weft skew (%) = Maximum distance between weft yarn (strip) skew and horizontal × 100 surface width
4.3.6 Appearance ironing quality shall comply with 3.11. 4.4 Determination of physical and chemical performance indicators
4.4.1 The shrinkage rate of the main parts of the finished product after dry cleaning shall comply with 3.12.1, and the test method shall comply with F2/T80007.3--1999. 4.4.2 The wrinkle level difference of the finished product after dry cleaning shall comply with 3.12.2, and shall be compared with the wrinkle sample of men's suits. 4.4.3 The shrinkage rate of the main parts of the finished product shall comply with 3.12.3, and the test method shall comply with the relevant provisions in GB/T8629. 4.4.4 The peel strength of the adhesive interlining part of the finished product shall comply with 3.12.4, and the test method shall comply with FZ/T80007.1-1999. 4.4.5 The permissible degree of color fastness of finished products shall be in accordance with 3.12.5. The test methods for color fastness shall be in accordance with GB/T3920-1997, GB/T 3921-1997, GB/T 3922-1995, GB/T 5711-1997, GB/T 8427-1998 and GB/T 18886-2002.
4.4.6 The permissible degree of pilling of finished products shall be in accordance with 3.12.6. The test method shall be in accordance with GB/T4802.1-1997 and compared with the pilling samples of combed wool fabrics (suede, glossy) and carded wool fabrics. 4.4.7 The degree of seam cracking in the main parts of the finished products shall be in accordance with 3.12.7. The test method shall be in accordance with Appendix A. The sampling locations shall be in accordance with Table 13.
Name of sampling part
Back seam
Sleeve seam
Back seam of trousers
Side seam of trousers
Crotch seam
Sampling part regulations
25 cm downward from the center of the back collar
Back sleeve bend
10 cm downward from the sleeve cavity
Centered by half of the back gantry arc
Centered by the upper third of the trouser side seam
Centered by the upper third of the crotch seam
4.4.8 The allowable strength of the back crotch seam of trousers shall comply with the provisions of 3.12.8. The sampling parts shall comply with the provisions of Appendix B. The test method shall comply with the provisions of GB/T 3923.1-1997.
44.9 The limit of formaldehyde content released by the finished product shall be in accordance with 3.12.9, and the test method shall be in accordance with GB/T2912.11998. 4.4.10 The permissible pH value of the finished product shall be in accordance with 3.12.10, and the test method shall be in accordance with GB/T7573--2002. The test method for the composition and content of the raw materials used in the finished product shall be in accordance with 4.4.11
of GB/T2910--1997, GB/T2911-1997 and other standards.
4.4.12 For the sampling sites of the physical and chemical performance tests not mentioned here, representative samples can be selected at will on the finished product according to the test items. 5 Inspection classification rules
5.1 Inspection classification
The inspection of finished products is divided into delivery inspection, general type inspection and type inspection. 8
5.1.1 Delivery inspection shall be in accordance with the provisions of Chapter 3, except for 3.12. 5.1.2 General type inspection shall be in accordance with the provisions of Chapter 3, except for 3.12.7 and 3.12.8. 5.1.3 Type inspection shall be in accordance with the provisions of Chapter 3 (only used in cases such as quality arbitration). 5.2 Rules for quality grade classification
FZ/T 81003—2003
The quality grade of finished products is based on the existence of defects and their severity. The individual products in the sampled samples are graded according to the number of defects and their severity, and the batch grade is divided according to the number of individual products in the sampled samples. 5.2.1 Defects
A single product that does not meet the technical requirements specified in this standard constitutes a defect. According to the degree of non-compliance of the product with the standard and the impact on the performance and appearance of the product, defects are divided into three categories. a) Serious defects
Defects that seriously reduce the performance of the product and seriously affect the appearance of the product are called serious defects. b) Major defects
Defects that do not seriously reduce the performance of the product and do not seriously affect the appearance of the product, but are more seriously inconsistent with the provisions of the standard are called major defects.
c) Minor defects
Defects that do not meet the requirements of the standard but have little impact on the performance and appearance of the product are called minor defects. 5.2.2 Basis for judging quality defects
See Table 14.
Appearance and sewing
Minor defects
The trademark is not straight and obviously skewed; the nail
trademark line does not match the color of the fabric.
Ironing is not smooth; there is a bright shine.
There are dead threads on the surface with a length of 1.0 cm,
yarn hair with a length of 1.5 cm, more than 2 pieces;
There are slight stains. The stain is less than or equal to
2.0 cm2, and the splash is less than or equal to
4 cm2.
The collar shape is inconsistent on the left and right, the fold is not straight, and the difference is more than 0.6cm (comparison between the two shoulders and the lining); the collar and the placket are slightly raised and not straight; the bottom collar is exposed, the chest pocket and sleeves are not straight and straight.
The exposed needle holes of the lining (seam edge) are less than
3cm.
The collar is not straight, the collar surface is not tight enough; the notches overlap.
Major defects
The instructions for use are inaccurate.
Slight yellowing and discoloration.
There are obvious stains. The stain is larger than
2.0cm2, and the splash is larger than
4.0cm2.
The collar and placket are seriously raised.
The exposed eye of the fabric (seam edge) is less than
1 cm; the exposed eye of the lining (seam edge) is
greater than or equal to 3 cm.
Serious defects
Missing items in the instructions for use.
Degumming, seepage
glue, wrinkling in the adhesive interlining.
Deterioration, damage.
Serious stains, stains greater than
50 cm2.
FZ/T 81003---2003
Appearance and sewing
Minor defects
Table 14 (continued)
Pockets are skewed; uneven; stitching lines are clearly
wide or narrow; the height difference between left and right pockets is greater than
0. 4 cm; the front and back are greater than 0. 6 cm.
Sleeve: asymmetrical; the hem is reversed; the width is greater than 0.3cm; the length is greater than 0.6cm.
The length of the sleeve slit is greater than 0.5cm.
Gauze sleeve: not round; the fit is uneven;
The sleeve rise is not flat.
Shoulder, sleeve, sleeve seam, side seam, seam
Major defects
Uneven; inconsistent inclination; the difference between the two shoulders is greater than 1.0cm. The difference between the sizes is greater than 0.5cm.
Cross seam: the difference is greater than 0.7cm.
Bottom: inconsistent in width; not straight;
Slightly warped.
The side pockets of the trousers are obviously uneven and not straight; the size of the pockets differs by more than
0.5cm; the height of the upper opening of the side pockets is higher or lower, and the difference is greater than 0.5 cm.
The back pocket of the trousers is not round, square, or flat; the inside of the pocket cover is obviously spitted out; the width of the inlay is narrower than 0.3 cm; the pocket cover is smaller than the pocket opening by more than 0.3 cm.
The lengths of the two trouser legs are inconsistent, and the difference is greater than 0.5 cm; the size of the trouser legs is inconsistent, and the difference is greater than 0.4 cm.
Dart: not straight; the tip has a pocket; there are
lengths; the front and back are inconsistent, the left and right are not
symmetrical, and the difference is greater than 1.0 cm; the strings are asymmetrical, and the difference is greater than
0.7 cm.
The sewing line is not straight; the width is uneven
hook; it is not flat; the double
track at the connection is obviously greater than 1.0cm; there is no backstitch at the starting and falling needles; there are two single
skips and continuous skipped stitches at 30cm: the upper and lower threads are slightly
tight and not suitable for tension.
The bottom edge is seriously tilted.
The pocket is obviously fuzzy.
The lengths of the two trouser legs are inconsistent, and the difference is greater than
1cm; the left and right sizes of the trouser legs are inconsistent, and the difference is greater than
0.6cm.
The string is not nailed firmly (the end is lifted).
The fuzz, fall-off, and leakage are less than 2.0cm; the tightness of the upper
and lower threads is seriously inappropriate, affecting the
fastness.
Serious defects
Hair, shedding, leakage greater than or equal to 2.0cm;
Chain line jumper, broken wire, damage.
Appearance and sewing
Specification tolerance
Minor defects
Table 14 (continued)
Collar stop is not straight; spitting; collar
The length of the tip is inconsistent, with a difference of 0.3cm
Serious defects
The difference in length of the collar corner is greater than 0.5cmz
The deviation of the gauze collar is greater than or equal to 1.0cm;
~0.5cm; the collar is not flat; the gauze
collar is seriously uneven. No. 1
Collar deviation is 0.6cm~0.9cm.
Neckline: The width is not consistent, the lower bed;
The line distance on the reverse side is greater than 0.4cm or
On the bed.
There are wiring and jumper wires at the
position; the collar corners are hairy.
The front and the inner placket are not straight and smooth; the length
front and the inner placket have tear marks, and the length is different
0.4 cm~0.6 cm;
The length of the sleeves is different by 0.6cm
The length of the front placket of the trousers is different, and the difference is greater than
0.3cm; the stop of the placket is obviously reversed
; the stitching of the front placket is obviously tight
and uneven.
The crotch and the back crotch of the trousers are obviously not round
smooth and smooth; the sealing is not neat, and the bottom of the trousers is uneven; the back seam is single-line.
Buttonhole is skewed, and the difference between buttonhole and eye is greater than 0.3cm.
The color difference of surface parts does not meet the requirements of this standard within 1 level; the color difference of lining cloth is less than 3 levels.
The color and hue of sewing thread are not compatible with the fabric; the color of button thread and button is not compatible.
Parts 2 and 3 exceed the requirements of this standard.
Greater than or equal to 0.7cm; the difference between the short sleeve lengths of the two parts is greater than or equal to 0.9cm.
The sealing of each part is not firm; the back seam is flat and the thread is broken.
Buttonhole jumps and opens; the button falls off.
The color difference of surface parts exceeds the requirements of this standard by more than 1 level.
Part 1 exceeds the requirements of this standard.
For stripes and grids, the weft skew exceeds the standard of this standard by 50% or less.
Below the standard by 2 needles (including 2 needles).
The specification exceeds the standard by 50% or less.
The difference between buttonhole spacing is greater than or equal to
0.5cm; the skew is greater than or equal to
0.3cm; the yarn is frayed.
The standard is more than 50%.
Below the standard by more than 2 needles.
The specification exceeds the standard by 50% or more.
Jumping, open thread, and hair leakage.
FZ/T 81003—2003
Serious defects
Fabric has reversed and straight hair, and the straight hair direction of the whole body is inconsistent
; the straight hair direction of special patterns is inconsistent.
Specifications exceed the requirements of this standard by 100%
or more.3cm; Yarn frayed.
More than 50% of the standard.
Below the standard by more than 2 stitches.
Specifications exceed the standard by 50% or more.
Jumping, open thread, hair leakage.
FZ/T 81003—2003
Serious defects
Fabric has reversed and straight hair, and the whole body is not consistent in the straight direction; the special pattern is inconsistent in the straight direction.
Specifications exceed the standard by 100% or more.3cm; Yarn frayed.
More than 50% of the standard.
Below the standard by more than 2 stitches.
Specifications exceed the standard by 50% or more.
Jumping, open thread, hair leakage.
FZ/T 81003—2003
Serious defects
Fabric has reversed and straight hair, and the whole body is not consistent in the straight direction; the special pattern is inconsistent in the straight direction.
Specifications exceed the standard by 100% or more.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.