GB 4706.68-2003 Safety of household and similar electrical appliances Particular requirements for drives for vertically moving garage doors for residential use
Some standard content:
All technical specifications of this part of GB4706 are mandatory. OB 470668—2003/1EC 60335-2-95.1998 This part is equivalent to 1EC60335-2-S5:1998% Safety of household and similar circuit electrical appliances Part 2: Particular requirements for drives for heavy-duty vertical brake garage doors for residential use 3. This part is used in conjunction with (GB4706.1-19984 Safety of household and similar inverters - Part 1: General requirements). The parts marked "applicable" in this part indicate the corresponding parts in GB4706.1-1998. The parts marked "replacement or modification" in this part are subject to this part. The parts marked "added" in this part indicate the clauses added to the applicable clauses in GB4705.1-1998. This part was proposed by China National Electrical Industry Federation and submitted to the National Technical Committee for Standardization of Household Electrical Appliances. The main drafting units of this part are Shenzhen Inspection and Quarantine Bureau of the People's Republic of China and China Household Electrical Appliances Research Institute. The main drafters of this part are Xie Puxiong, Bu Xuwei, Yu Dejun, Liu Tibi, Xu Yulie, Li Jun, Xiang Bixiao, Lu Wenjun, GB4706.682 003/IEC60335-2-95:1998 IFEC Foreword
1) IEC (International Electrotechnical Commission) is an international standardization organization composed of all national electrotechnical committees (IFC National Committees). Its purpose is to promote international cooperation in electrical and electronic standardization. To this end, IEC carries out international standardization activities and publishes international standards. The formulation of these standards is entrusted to technical committees. Therefore, any IFC National Committee interested in this work may participate in the formulation. International, non-governmental and non-governmental organizations with ties to IEC may also participate in this work. The IEC and the International Standardization Organization (IFC) work closely together according to the agreement between the two parties. The formal resolutions of IEC on technical issues formulated by the technical committees in which all national committees with special interests participate can represent the relevant issues. In order to achieve international consensus, this will be formally adopted by the IEC Regional Committee in the form of a standard, technical bulletin or academic code, and recommended for international adoption, and the National Committees will make decisions on this.
4) In order to achieve international consensus, the IEC National Committees will use the international standards as much as possible in their respective countries and regional standards. The differences between IEC standards and the corresponding national or regional standards should be clearly stated in the latter. 5) IFC does not formulate the procedures for the approval mark. If a device claims that it complies with a certain standard of IFC, IFC is not responsible for this.
6] It is necessary to consult the International Standard Committee for the purpose of obtaining patent rights, and the committee shall not be responsible for any or all of the patent rights.
This standard was prepared by the first technical committee (Safety of Household and Similar Appliances). This standard is for IEC This standard is based on the following documents:
6_1360/FTHS
References
$1/1408/RVL
Full information on the status of the standard can be found in the above resolution report. This standard is based on the third edition of IEC60335-1991 and should be used in conjunction with the revised version of JEC6J335-1 and its supplements. This standard supplements or modifies the applicable clauses in IEC50.3A5-1 and converts it into IEC standard: Safety requirements for electric devices for vertically moving garage doors.
The clauses of IEC60335-1 not included in this standard shall apply under reasonable circumstances. If "added\modified" or "missing" is marked in this standard, the relevant clauses of IEC60335-1 shall be incorporated accordingly. Note 1, to use the following printing in the standard, requirements: Luo 7 words according to:
visual proof of law:
one: small Luo words according to,
product design words in the first chapter of the text, when the policy a reform of the text involves time, the bottle name river also need to know the cumulative rest words Note 2: the time the first life points to confirm the record and the break with 101 open average comprehensive number, - the country of origin has the following differences:
—6,1; allow 0 class appliances (F this>,
?.1: sometimes require additional standards (additional years and relevant countries). .12.2: require additional notice and identification (time Canada big accumulation of US pressure): -11.?, acid test case not company (return) -19.9: require operation overload test (relevant countries). ---20.101, no test (USA) GB 4706.68—2003/1EC B0335-2-95:1998 1 Scope
GB4706.68-2003/IEC60335-2-95 1998 Safety of electrical appliances for household and similar purposes
Particular requirements for drives for vertically moving garage doors for domestic use
G1706.1—9 This chapter replaces: This part of B471S deals with the safety of electric motors for garages used for vertical opening and closing, with a rated voltage not exceeding 350 V for single-phase devices and not exceeding 430 V for other appliances. This part also covers the additional hazards associated with the movement of electric garage doors
1 In the case of new equipment such as 1C1, NOTE 2 The motors are designed to move the garage door in a manner that is not more than 100 V. 3. This section is intended for use with fire protection devices in conjunction with mechanical devices. This section does not apply to other hazards associated with the mechanical structure of the door itself. As far as practical, this section applies to all hazards arising from the appliance. The general technical considerations for this section are only for children playing with the appliance, but consider the possibility that children may approach the door. 5. The following situations apply:
- For the user's device: Special requirements must be made: - In many countries, this requirement is stipulated by other national departments for mechanical protection and similar static doors. Please note the following
- The drive device of a garage door used in a household! - When leaving doors and windows tight, seat shutters and similar devices must be installed. Equipment dynamics (C60335-2-:7): --- Not suitable for commercial and industrial use in special places, such as the presence of night-time or high-energy environments (with steam or gas), 2.2.9 of this chapter of GE4706.1-3, except for the following exceptions, and the following certificates are recommended for use:
Normal operation narmalaperatian
The appliance works under the following operating conditions:
The drive motor of the door can be stored in the following seven operations: 1. The drive device of the door is provided to work with the door in the upper fast state. 2.101
Drive device drlve ||tt| |Motors and other components that control the movement of lathe doors, Note: Examples of components are motors, controllers, actuators and built-in protection systems, 2.102
Built-in protection systems inherent protection systems installed inside the drive assembly to provide optical protection, GB4706.68—2003/[EC60335-2-95,19982.103
Non-inherent enirapmeatprotection devices Non-inherent enirapmeatprotection devices Installed with the door, providing enirapmeat protection when actuated, it is not part of the drive assembly. Note: Examples of active photoelectric protection devices are biased-ufrsitch
A switch that automatically returns to the off position when the actuating element is released. 2,105
Numerical rated load
Force or force specified by the manufacturer for the drive device, 3 General requirements
The contents of the diagnostic chapter of GT270F.1-1998 are applicable to all 4 General provisions of the test
The liquid grass of H4106.1-1093 are applicable except for the following items, 4.2 This clause adds the following content:
If the test must be carried out with a door, avoid using the most unfavorable type of door suitable for the drive set. Note: The parts specified in the product specification must be standard equipment. 5 Blank chapter
6 Classification
This chapter of GB47U6.1:1992 is applicable except for the following content. 6.1 The following amendments are made to this series:
In the seven main protection surfaces, the equipment shall be considered as Class D, Class D, and Class D. 5.2 The following additions are made to this series:
The rating of the external protective equipment shall be at least IPX.
The external protective equipment without built-in fire protection shall also provide an appropriate level of protection against the entry of inappropriate foreign bodies, at least TP+4: 7 Markings and instructions
B4, (except for the following items in this chapter, all use .7.1 This article adds that the downlink internal rate:
should be marked with the actual load, unless the door is optimized together with the driving device. 7.12 The following content is added to this article:
The instruction manual (book) should stipulate that the instructions should be strictly followed for safety. Save this purple description bZxz.net
Using the Nomin (book) does not include the above instructions
Do not allow children to play with the gate controller
Set the tunnel excavator function Keep away from children; keep the door open and away from the moving door until it is fully opened or closed. When the door is open, the door may squeak due to weak springs, broken assembly, or the door may fall due to imbalance. , you should be careful when sending scammers 2
Frequency, play and installation, there are no signs of damage caused by imbalance; if you want to participate or adjust, do not buy it, because the equipment will reduce the balance of the equipment. Harmful! Check the doors and objects placed on the ground at a height of mm every month. They can move in directions if necessary. If necessary, perform verification and re-inspection. Improper structure may cause risk. Instructions for use (book) should include:
- Detailed information on how to use the movable ring to insert the stomach: 1. Information about adjusting the door and the movable device. 7.12.F This article adds the following content:
The installation description should include detailed information on the installation equipment and its necessary components (including all non-built-in protective equipment), and indicate the type and maintenance of the door used for opening the mechanical equipment. Yes, the installation instructions should stipulate the following content:
Full instructions for installation
Incorrect installation will lead to serious installation problems. Saigou
Installation of Shuozhou books should include the following inner wear:
Before installing the account, clear all necessary cell boxes and chain boxes and disable all vents in the room 1. Make necessary preparations, Liu Suo; before changing the transmission device, it should be confirmed that it is in good mechanical condition and correctly balanced, and can stop and open: the action components of the translation device The installation height is too low, so the fixed controller should be installed within the visual range of the door and away from the shipping components. The installation fee is at least 1.5U: Note: For those who need a key, There is no requirement to adjust the minimum degree..: Place the warning signs such as anti-change and durability at the position shown or near the time-travel controller: Place the manually placed meter permanently in place. Due to the close payment of two pieces of deposit: after installation, it should be ensured that the mechanical carbon bonding structure is correct, and when the door touches the 43mm body placed on the ground, the moving parts can move,
7.12 The following content is added to this system:
The labels specified in 7.1C1 to 7.103 shall be easy to read, durable and suitable for long-term use. 7.101 The driving device shall be provided with the following information: Labels should be kept away from the door where the goods are transported.
The warning label should be displayed with a graphic with a height not less than S0mn:, and its form and color should comply with the provisions of IS) 3864 General inspection to check its intermediary performance
The vehicle, the four-12 graphic is suitable for the product, and the 7.102 single-acting device provides a warning label with low oxygen content: Warning - branch insurance||tt| |Regular inspection and verification of compensation if necessary
Make sure that the single door can move in the reverse direction when the fast body is late and high, and passes the regulatory inspection and meets its qualifications
7.103 drive device A description of the possible locations for mounting hardware should be provided and their suitability checked by current controls.
Protection of electrical and live parts
Use
8.2 strips for inner wear and outer wear plus the following inner ring:
GB 4706.682003/IEC 6C335-2-95;1998. When the adjustment mechanism requires a worker to press it, it is basically Parts that are insulated and separated from the cored parts by means of standard specifications are usually included in the adjustment:
9 Starting up of electric appliances
[\B470F, this chapter of 1-199R Customer, not applicable, 10 Input power and current
This chapter of B47U6.1-1H98 is applicable except for the following content. 1C.1 The content of this series has been corrected as follows:
The measured maximum channel is not determined by the average value when the per capita rate is entered, and the influence of the automatic current is ignored. 10.2 The content of this article has been revised as follows | | tt | Content generation:
This article provides a door driving device that works for 2 minutes. The dynamic installation technology of the light door has a cycle of lifting and closing the door. 12 empty chapters | The rate content of 14 Empty Chapter
15 Moisture Resistance
GB476.1--1998 is applicable, and the chapter of 16 Electric Leakage and Electrical Strength
CB47J5.1-1048 is applicable. For internal customers, it is suitable for all months. The overload protection of 17 transformers and related circuits, B4735.119, is suitable for all internal wear.
18 resistance
6B4705.11968 is suitable for domestic customers. 19 Abnormal work
1703.1-198 Except for the following content in this chapter, the provisions of this article 19.9 are not applicable.
19.10 The inner penetration of this article is not used.
19.13 The following content is added to this article;
After the other tests, the equipment shall comply with the requirements before 70.1.12 to 20.107. 20 Certainty and hazards of sailing equipment
The rules of K4706,1-158 are applicable except for the following domestic customers. 20.2 This system has added violations,
GB 4706.68-2003/IEC 60335 -2-95:1998 is going to be installed in? The above moving parts of the drive unit do not require protection. 20. The 101-seat movable frame should be able to prevent the door from being closed and forced to pass the following test to check its performance:
The movable frame is powered by the rated voltage but does not work. A rated mass load of 1.2% is applied for 30 minutes. , if the door resistance driving device provides, then the load is applied to the door, the magnitude of which is equal to the strong force exerted by the door, except for the steady movement caused by the variable operation in the system, there will be no other movement, the battle is big When the door is unfavorable and the measuring instrument is not powered on, the light test is carried out with the drive device powered at .85 times the rated self-voltage and disconnected from the power supply. .29, 102 built-in central protection system ignition work It should be able to prevent injuries before the door closes. The hazards must be tested as follows.
According to the installation instructions, the moving assembly and door should be assembled together, and the force exerted by the moving force must be controlled. Set it to the maximum value, so that the non-internal mutual protection equipment is left in an inoperative state, the actuating device operates at rated voltage, the door is closed, and the barrier is placed anywhere on the ground and 0mn - but not Double located doors on the first 3 down from all open positions! Within the range of m. The door should be movable and open within the obstacle hook 2 for at least Gm, and non-moving equipment should be inspected with a rated power supply of 0.85. 20.13 The internal frame protection system should ensure that the time before the door needs to be moved when installing the frame should not be too long. Its qualification is checked through the test carried out at low speed. The actuating device is based on the rated voltage, and any limit switch is in an inoperative state. After the closing action starts, the alarm clock should move in: After starting the door opening movement, the moving device should stop within 39≤. The drive device is powered by 5 times the constant voltage of C. The normal start of test 20.104 without built-in anti-pinch protection should be able to prevent worrying accidents caused by the door being closed, and it shall pass the following test to become qualified || tt||Install the actuating device and supply power with rated voltage according to the original installation manual: start the door closing movement, start the non-internal anti-reverse protection device, the drive device performs a reversal movement, and the non-internal anti-reverse protection device starts or stops the door. The movement death method begins, the movement is set to 3. The bottle is centered quickly, the spirit is tested again, the flow 1. Can be tested without evil,
Note 2, with the grid replacement piece and the singing bone Non-retained fire protection devices with distributed power supply shall be supplied in accordance with the provisions of the entire installation. 20.105 The non-dark protection device equipped with an active photoelectric protection device should be able to detect stationary and moving objects and cause the door to move and then reverse.
Pass the following test to prove its qualification.
Report the installation instructions and install the non-internal light protection device. Install the rated power supply center of the retractor and start the door closing movement to turn the road into white. Place free stationary and moving screen obstructions at the door respectively. The object is high, m, long and 3im wide. Place it under the door and make its main input directly connected to the non-opening flow of the door. First, increase the volume and then place motion barriers 30mm from both ends of the door to obtain a diameter of 50mm.The length of the 850mm, each end of the level and make it 900mm above the ground, centered on the beam of the non-internal protection. The body moves through the beam at 45 degrees. During each test, the non-internal protection device should be able to move and make the door move in reverse. Method: The test can be carried out without the door. GB 4706.68-2003/X: 60335-2-95, 1998200 has a pressure-effective non-internal protection device that can measure the depth of the spring stop. The door movement stops and moves in reverse before the door exerts too much force. Pass the speed test to determine its eligibility. Install the non-internal protection device according to the installation instructions. The drive device is powered by rated voltage and starts closing the door. A static object with a height of 4m, a width of 2m and a length of at least 2m is placed in the lower well of the door and vertically parallel to the door. First, it is placed in the center and then 100mm away from both ends of the door opening. The non-internal anti-pinch protection device should be able to act and make the door move in the opposite direction. After pushing the edge, the force applied to the obstacle is not less than 150N.
In the test, a friction object with a size of 250mm×250mm and a length of at least 200m is used. However, the force is measured. 20.107 When the dynamic closing period of the door is reached, the wiring connected to the non-internal anti-pinch protection device and other external controllers is slightly open, which should not affect the action of the internal anti-pinch protection system. Check compliance by repeating the relevant tests of 20.102 and 20.193 and applying one sensitive condition each time. Note: 1. If the "no activation" is performed during the test, it is considered that the requirements are met in 3.n.2. Check the circuit. 3. The door operation test can be performed without any delay. 20.108 During the closing movement of the door actuator, starting the manual controller should enable the door to be opened and reversed. During the door movement, it should only stop movement. Check its compliance by manual test. For two-button control type, pressing the "up\" button should stop and reverse the closing movement; pressing the "down" button should not affect the opening movement! 1. Pressing the "Stop" button shall stop the movement. The door may not be operated.
20.109 The door shall be equipped with a manual release device to enable manual operation of the door. The manual release action shall not cause any danger of shock or accidental movement of the door.
During the closing period, the door shall be operated at different heights to check the compliance of the door. The release device shall be able to be switched with a force not exceeding 226N and a torque not exceeding 1.6N, m. The test is carried out with the protective device in the inoperative state and then without the drive supply. 20.110 After the movement has stopped, the monitoring device shall not automatically restart. Note: This may be caused by an interruption or thermal circuit breaker. The following test objects are used to verify the compliance: The equipment is supplied with rated voltage and operated in the normal working state. Then, the power supply is disconnected. After the power supply is reconnected, the drive device fails to restart automatically. The equipment continues to work and simulates the action of the thermal circuit breaker. The drive device shall not restart automatically after the failure is eliminated. 21 Mechanical stress The contents of CB4775.1-1998 apply. 22 Structure The contents of this chapter of GR47C.1-1998 apply except for the following contents: 22.101 This clause adds the following contents: The drive device can only be adjusted by using tools. The compatibility is checked by standard inspection. 22.12 The drive device shall be equipped with relevant components that meet the requirements of the vehicle part. Compliance is checked by inspection.
CB 4706.68—2003/:C 60335-2-95:199822.103 The force produced exceeds 15uN. The moving device shall have an internal anti-pinch protection system and a non-flash protection device. Other moving devices shall be equipped with a built-in anti-smuggling protection system or with a built-in double-pinch protection device. Compliance is checked by reverse measurement. The non-built-in anti-pinch protection device is in a non-operating state. The force is determined when the whole moving device is in normal operation at rated voltage or during the test of Chapter 19. When the door is in the unfavorable position, the measurement is made in the vertical direction at the edge of the door. 2.104 The drive device is not equipped with a pad that makes the light protection mechanism inoperative. However, the automatic shut-off switch intended to be fixed in the vehicle can be checked when one of the protective mechanisms is inoperative. Check its compliance by regulatory inspection.
22.105 The actuating member in the manual lifting cover shall be red. Check its compliance by regulatory inspection.
22.106 If the manual actuator is provided with a three-button controller, all other manual controllers shall be of the same type. Check its compatibility by tax inspection.
1. This requirement is only applicable to the controller for controlling the operation of the door. Note 2: The controller may not be a temperature control or a wall safety meter. 22.107 The door can only be opened or closed by the manual actuator. Check its compliance by regulatory inspection.
23 Internal wiring
The contents of this chapter of GB4706.1199B are applicable. 24 Components
The contents of this chapter of GB170h.1-1998 are applicable except for the following contents. 24.1.3 This section adds the following:
For switches that can switch the power supply of the appliance when the release setting is activated, the working cycle shall be 100 times. 25 Power supply connections and external soft shoes
This clause of B4706.12398 is applicable except for the following warnings. 25.7 This section adds the following:
The power supply cord of the drive device used outdoors shall be covered with an epoxied rubber sheath and shall not be lighter than the protective cord of the previous model (Line 57 in TE 60245).
26 External conductor terminal
This chapter of GB4736.1-108 applies
27 Grounding measures
This chapter of GB4736.1-1998 applies: 28 Grounding and connection
This chapter of GB4706.1-1996 applies, GB 4706.68-2003/1E4 applies: 60335-2-95,159829 phase distance, electrical insulator and insulation distance GB4735.1-1098 are applicable. 30
Heat resistance, flame resistance and electrical insulator resistance
6B4706.12 In addition to the content specified, the following passage: 30.2.2, this content is not applicable.
31 Rust prevention
"B4735.1-18, except for the following memory, this clause is applicable to increase the reverse customer,
For components installed outdoors, the gasket with a grade of 2 in TFC35R-2 needs to be tested and checked for its qualification. Before the test, use a Zerong exhaust needle to measure the coating. The steel needle The end product has a 40\ dimensional angle and a tip radius of (.25mm). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of inrm/min to the surface of the device. Five scratches are made. The interval between the scratches must be at least 2mm and the interval between the scratches must be at least 2mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. The provisions of this chapter of GB/70,1-19 for radiation, toxicity and similar hazards are applicable. 8. Sectional doors with high guide rails for safety and comfort. Sectional doors with high guide rails. Figure 131. FA 4706.68—2003/ICC 60335-2-95:1998 Single-board door with annual business and navy style
Water lifting door
Special curtain door
Examples of various car single doorsA static object with a width of 2 m and a length of at least 2 m shall be placed under the door and vertically parallel to the door. First, place it in the center and then place it 100 mm away from both ends of the door opening. The non-internal anti-pinch protection device shall be able to act and make the door move in the opposite direction. After pushing the edge, the force applied to the obstacle shall not exceed 150 N.
In this test, a friction object with a size of 250 mm × 250 mm and a length of at least 200 m shall be used. However, the force shall be measured. 20.107 When the door reaches the dynamic closing period, the wiring connected to the non-internal anti-pinch protection device and other external controllers shall be slightly open, which shall not affect the action of the internal anti-pinch protection system. Check compliance by repeating the relevant tests of 20.102 and 20.193 and applying one sensitive condition each time. Note: 1. If the "no activation" is performed during the test, it is considered that the requirements are met in 3.n.2. Check the circuit. 3. The door operation test can be performed without any delay. 20.108 During the closing movement of the door actuator, starting the manual controller should enable the door to be opened and reversed. During the door movement, it should only stop movement. Check its compliance by manual test. For two-button control type, pressing the "up\" button should stop and reverse the closing movement; pressing the "down" button should not affect the opening movement! 1. Pressing the "Stop" button shall stop the movement. The door may not be operated.
20.109 The door shall be equipped with a manual release device to enable manual operation of the door. The manual release action shall not cause any danger of shock or accidental movement of the door.
During the closing period, the door shall be operated at different heights to check the compliance of the door. The release device shall be able to be switched with a force not exceeding 226N and a torque not exceeding 1.6N, m. The test is carried out with the protective device in the inoperative state and then without the drive supply. 20.110 After the movement has stopped, the monitoring device shall not automatically restart. Note: This may be caused by an interruption or thermal circuit breaker. The following test objects are used to verify the compliance: The equipment is supplied with rated voltage and operated in the normal working state. Then, the power supply is disconnected. After the power supply is reconnected, the drive device fails to restart automatically. The equipment continues to work and simulates the action of the thermal circuit breaker. The drive device shall not restart automatically after the failure is eliminated. 21 Mechanical stress The contents of CB4775.1-1998 apply. 22 Structure The contents of this chapter of GR47C.1-1998 apply except for the following contents: 22.101 This clause adds the following contents: The drive device can only be adjusted by using tools. The compatibility is checked by standard inspection. 22.12 The drive device shall be equipped with relevant components that meet the requirements of the vehicle part. Compliance is checked by inspection.
CB 4706.68—2003/:C 60335-2-95:199822.103 The force produced exceeds 15uN. The moving device shall have an internal anti-pinch protection system and a non-flash protection device. Other moving devices shall be equipped with a built-in anti-smuggling protection system or with a built-in double-pinch protection device. Compliance is checked by reverse measurement. The non-built-in anti-pinch protection device is in a non-operating state. The force is determined when the whole moving device is in normal operation at rated voltage or during the test of Chapter 19. When the door is in the unfavorable position, the measurement is made in the vertical direction at the edge of the door. 2.104 The drive device is not equipped with a pad that makes the light protection mechanism inoperative. However, the automatic shut-off switch intended to be fixed in the vehicle can be checked when one of the protective mechanisms is inoperative. Check its compliance by regulatory inspection.
22.105 The actuating member in the manual lifting cover shall be red. Check its compliance by regulatory inspection.
22.106 If the manual actuator is provided with a three-button controller, all other manual controllers shall be of the same type. Check its compatibility by tax inspection.
1. This requirement is only applicable to the controller for controlling the operation of the door. Note 2: The controller may not be a temperature control or a wall safety meter. 22.107 The door can only be opened or closed by the manual actuator. Check its compliance by regulatory inspection.
23 Internal wiring
The contents of this chapter of GB4706.1199B are applicable. 24 Components
The contents of this chapter of GB170h.1-1998 are applicable except for the following contents. 24.1.3 This section adds the following:
For switches that can switch the power supply of the appliance when the release setting is activated, the working cycle shall be 100 times. 25 Power supply connections and external soft shoes
This clause of B4706.12398 is applicable except for the following warnings. 25.7 This section adds the following:
The power supply cord of the drive device used outdoors shall be covered with an epoxied rubber sheath and shall not be lighter than the protective cord of the previous model (Line 57 in TE 60245).
26 External conductor terminal
This chapter of GB4736.1-108 applies
27 Grounding measures
This chapter of GB4736.1-1998 applies: 28 Grounding and connection
This chapter of GB4706.1-1996 applies, GB 4706.68-2003/1E4 applies: 60335-2-95,159829 phase distance, electrical insulator and insulation distance GB4735.1-1098 are applicable. 30
Heat resistance, flame resistance and electrical insulator resistance
6B4706.12 In addition to the content specified, the following passage: 30.2.2, this content is not applicable.
31 Rust prevention
"B4735.1-18, except for the following memory, this clause is applicable to increase the reverse customer,
For components installed outdoors, the gasket with a grade of 2 in TFC35R-2 needs to be tested and checked for its qualification. Before the test, use a Zerong exhaust needle to measure the coating. The steel needle The end product has a 40\ dimensional angle and a tip radius of (.25mm). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of inrm/min to the surface of the device. Five scratches are made. The interval between the scratches must be at least 2mm and the interval between the scratches must be at least 2mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. The provisions of this chapter of GB/70,1-19 for radiation, toxicity and similar hazards are applicable. 8. Sectional doors with high guide rails for safety and comfort. Sectional doors with high guide rails. Figure 131. FA 4706.68—2003/ICC 60335-2-95:1998 Single-board door with annual business and navy style
Water lifting door
Special curtain door
Examples of various car single doorsA static object with a width of 2 m and a length of at least 2 m shall be placed under the door and vertically parallel to the door. First, place it in the center and then place it 100 mm away from both ends of the door opening. The non-internal anti-pinch protection device shall be able to act and make the door move in the opposite direction. After pushing the edge, the force applied to the obstacle shall not exceed 150 N.
In this test, a friction object with a size of 250 mm × 250 mm and a length of at least 200 m shall be used. However, the force shall be measured. 20.107 When the door reaches the dynamic closing period, the wiring connected to the non-internal anti-pinch protection device and other external controllers shall be slightly open, which shall not affect the action of the internal anti-pinch protection system. Check compliance by repeating the relevant tests of 20.102 and 20.193 and applying one sensitive condition each time. Note: 1. If the "no activation" is performed during the test, it is considered that the requirements are met in 3.n.2. Check the circuit. 3. The door operation test can be performed without any delay. 20.108 During the closing movement of the door actuator, starting the manual controller should enable the door to be opened and reversed. During the door movement, it should only stop movement. Check its compliance by manual test. For two-button control type, pressing the "up\" button should stop and reverse the closing movement; pressing the "down" button should not affect the opening movement! 1. Pressing the "Stop" button shall stop the movement. The door may not be operated.
20.109 The door shall be equipped with a manual release device to enable manual operation of the door. The manual release action shall not cause any danger of shock or accidental movement of the door.
During the closing period, the door shall be operated at different heights to check the compliance of the door. The release device shall be able to be switched with a force not exceeding 226N and a torque not exceeding 1.6N, m. The test is carried out with the protective device in the inoperative state and then without the drive supply. 20.110 After the movement has stopped, the monitoring device shall not automatically restart. Note: This may be caused by an interruption or thermal circuit breaker. The following test objects are used to verify the compliance: The equipment is supplied with rated voltage and operated in the normal working state. Then, the power supply is disconnected. After the power supply is reconnected, the drive device fails to restart automatically. The equipment continues to work and simulates the action of the thermal circuit breaker. The drive device shall not restart automatically after the failure is eliminated. 21 Mechanical stress The contents of CB4775.1-1998 apply. 22 Structure The contents of this chapter of GR47C.1-1998 apply except for the following contents: 22.101 This clause adds the following contents: The drive device can only be adjusted by using tools. The compatibility is checked by standard inspection. 22.12 The drive device shall be equipped with relevant components that meet the requirements of the vehicle part. Compliance is checked by inspection.
CB 4706.68—2003/:C 60335-2-95:199822.103 The force produced exceeds 15uN. The moving device shall have an internal anti-pinch protection system and a non-flash protection device. Other moving devices shall be equipped with a built-in anti-smuggling protection system or with a built-in double-pinch protection device. Compliance is checked by reverse measurement. The non-built-in anti-pinch protection device is in a non-operating state. The force is determined when the whole moving device is in normal operation at rated voltage or during the test of Chapter 19. When the door is in the unfavorable position, the measurement is made in the vertical direction at the edge of the door. 2.104 The drive device is not equipped with a pad that makes the light protection mechanism inoperative. However, the automatic shut-off switch intended to be fixed in the vehicle can be checked when one of the protective mechanisms is inoperative. Check its compliance by regulatory inspection.
22.105 The actuating member in the manual lifting cover shall be red. Check its compliance by regulatory inspection.
22.106 If the manual actuator is provided with a three-button controller, all other manual controllers shall be of the same type. Check its compatibility by tax inspection.
1. This requirement is only applicable to the controller for controlling the operation of the door. Note 2: The controller may not be a temperature control or a wall safety meter. 22.107 The door can only be opened or closed by the manual actuator. Check its compliance by regulatory inspection.
23 Internal wiring
The contents of this chapter of GB4706.1199B are applicable. 24 Components
The contents of this chapter of GB170h.1-1998 are applicable except for the following contents. 24.1.3 This section adds the following:
For switches that can switch the power supply of the appliance when the release setting is activated, the working cycle shall be 100 times. 25 Power supply connections and external soft shoes
This clause of B4706.12398 is applicable except for the following warnings. 25.7 This section adds the following:
The power supply cord of the drive device used outdoors shall be covered with an epoxied rubber sheath and shall not be lighter than the protective cord of the previous model (Line 57 in TE 60245).
26 External conductor terminal
This chapter of GB4736.1-108 applies
27 Grounding measures
This chapter of GB4736.1-1998 applies: 28 Grounding and connection
This chapter of GB4706.1-1996 applies, GB 4706.68-2003/1E4 applies: 60335-2-95,159829 phase distance, electrical insulator and insulation distance GB4735.1-1098 are applicable. 30
Heat resistance, flame resistance and electrical insulator resistance
6B4706.12 In addition to the content specified, the following passage: 30.2.2, this content is not applicable.
31 Rust prevention
"B4735.1-18, except for the following memory, this clause is applicable to increase the reverse customer,
For components installed outdoors, the gasket with a grade of 2 in TFC35R-2 needs to be tested and checked for its qualification. Before the test, use a Zerong exhaust needle to measure the coating. The steel needle The end product has a 40\ dimensional angle and a tip radius of (.25mm). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of inrm/min to the surface of the device. Five scratches are made. The interval between the scratches must be at least 2mm and the interval between the scratches must be at least 2mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. The provisions of this chapter of GB/70,1-19 for radiation, toxicity and similar hazards are applicable. 8. Sectional doors with high guide rails for safety and comfort. Sectional doors with high guide rails. Figure 131. FA 4706.68—2003/ICC 60335-2-95:1998 Single-board door with annual business and navy style
Water lifting door
Special curtain door
Examples of various car single doors110 After the movement stops: the drive device shall not restart automatically. Note: This may be caused by an interruption or thermal circuit breaker. The following test object is passed to verify its qualification: The device is powered with rated voltage and works under normal working conditions. Then, the power supply is disconnected and after the power is reconnected, the drive device shall not restart automatically. The device is operated and the thermal circuit breaker action is simulated. Excluding the fault case, the drive device shall not restart automatically. 21 Mechanical excitation
The design content of CB4775.1-1998 is applicable. 22 Structure
This chapter of GR47C.1-1998 is applicable except for the following content: 22.101 This clause adds the following content:
The drive device can only be adjusted by using tools
Check its compatibility through standard inspection.
22.12 The drive device shall be equipped with relevant components that meet the requirements of the vehicle part. Check its compliance through visual inspection.
CB 4706.68-2003/:C 60335-2-95:1998 22.103 The drive device with a force exceeding 15uN shall have an internal anti-pinch protection system and a non-flash protection device. Other medical devices shall be equipped with a built-in anti-sell protection system or with a built-in double-clamp protection device. Compliance is checked by measurement in accordance with the standard test. Non-built-in protective devices are placed in the non-operating state. The force is determined when the actuator is in normal operation at rated voltage or during the tests of clause 19, when the door is in the extended position, measured in the vertical direction at the edge of the door. 2.104 The actuator is not provided with a washer that puts the protective mechanism in the non-operating state. However, an automatic shut-off switch intended to be fixed inside the vehicle may put one of the protective mechanisms in the non-operating state. Compliance is checked by standard test.
22.105 The actuating member in the manual lifting cover shall be red. Compliance is checked by standard test.
22.106 If the actuator is provided with a three-button controller, all other manual controllers shall be of the same type. Compliance is checked by inspection.
1. This requirement applies only to the controller that controls the operation of the door. Note 2 Controller n, avoid temperature control or wall safety meter. 22.107 Only the automatic control can open or close the door, and its compliance shall be checked by inspection.
23 Internal wiring
This clause of GB4706.1199B is applicable. 24 Components
This clause of GB170h.1-1998 is applicable except for the following contents. 24.1.3 This clause is added with the following contents:
For switches that can switch on the power supply of the appliance when the automatic release meter is activated, the working cycle shall be the minimum number of times. 25 Power supply connection and external soft shoe
This chapter of GB4706.12398 is applicable except for the following warnings. 25.7 This chapter adds the following content:
The power cord of the drive device used outdoors should be covered with epoxied rubber sheath, and should not be lighter than the protective cord (Line 57 in TE 60245).
26 External conductor terminal
This chapter of GB4736.1-108 is applicable.
27 Grounding measures
This chapter of GB4736.1-1998 is applicable. 28 Grounding and connection
This chapter of GB4706.11996 is applicable. GB 4706.68-2003/1E4: 60335-2-95,159829 phase distance, electrical insulator and insulation distance GB4735.1-1098 are applicable. 30
Heat resistance, flame resistance and electrical insulator resistance
6B4706.12 In addition to the content specified, the following passage: 30.2.2, this content is not applicable.
31 Rust prevention
"B4735.1-18, except for the following memory, this clause is applicable to increase the reverse customer,
For components installed outdoors, the gasket with a grade of 2 in TFC35R-2 needs to be tested and checked for its qualification. Before the test, use a Zerong exhaust needle to measure the coating. The steel needle The end product has a 40\ dimensional angle and a tip radius of (.25mm). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of inrm/min to the surface of the device. Five scratches are made. The interval between the scratches must be at least 2mm and the interval between the scratches must be at least 2mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. The provisions of this chapter of GB/70,1-19 for radiation, toxicity and similar hazards are applicable. 8. Sectional doors with high guide rails for safety and comfort. Sectional doors with high guide rails. Figure 131. FA 4706.68—2003/ICC 60335-2-95:1998 Single-board door with annual business and navy style
Water lifting door
Special curtain door
Examples of various car single doors110 After the movement stops: the drive device shall not restart automatically. Note: This may be caused by an interruption or thermal circuit breaker. The following test object is passed to verify its qualification: The device is powered with rated voltage and works under normal working conditions. Then, the power supply is disconnected and after the power is reconnected, the drive device shall not restart automatically. The device is operated and the thermal circuit breaker action is simulated. Excluding the fault case, the drive device shall not restart automatically. 21 Mechanical excitation
The design content of CB4775.1-1998 is applicable. 22 Structure
This chapter of GR47C.1-1998 is applicable except for the following content: 22.101 This clause adds the following content:
The drive device can only be adjusted by using tools
Check its compatibility through standard inspection.
22.12 The drive device shall be equipped with relevant components that meet the requirements of the vehicle part. Check its compliance through visual inspection.
CB 4706.68-2003/:C 60335-2-95:1998 22.103 The drive device with a force exceeding 15uN shall have an internal anti-pinch protection system and a non-flash protection device. Other medical devices shall be equipped with a built-in anti-sell protection system or with a built-in double-clamp protection device. Compliance is checked by measurement in accordance with the standard test. Non-built-in protective devices are placed in the non-operating state. The force is determined when the actuator is in normal operation at rated voltage or during the tests of clause 19, when the door is in the extended position, measured in the vertical direction at the edge of the door. 2.104 The actuator is not provided with a washer that puts the protective mechanism in the non-operating state. However, an automatic shut-off switch intended to be fixed inside the vehicle may put one of the protective mechanisms in the non-operating state. Compliance is checked by standard test.
22.105 The actuating member in the manual lifting cover shall be red. Compliance is checked by standard test.
22.106 If the actuator is provided with a three-button controller, all other manual controllers shall be of the same type. Compliance is checked by inspection.
1. This requirement applies only to the controller that controls the operation of the door. Note 2 Controller n, avoid temperature control or wall safety meter. 22.107 Only the automatic control can open or close the door, and its compliance shall be checked by inspection.
23 Internal wiring
This clause of GB4706.1199B is applicable. 24 Components
This clause of GB170h.1-1998 is applicable except for the following contents. 24.1.3 This clause is added with the following contents:
For switches that can switch on the power supply of the appliance when the automatic release meter is activated, the working cycle shall be the minimum number of times. 25 Power supply connection and external soft shoe
This chapter of GB4706.12398 is applicable except for the following warnings. 25.7 This chapter adds the following content:
The power cord of the drive device used outdoors should be covered with epoxied rubber sheath, and should not be lighter than the protective cord (Line 57 in TE 60245).
26 External conductor terminal
This chapter of GB4736.1-108 is applicable.
27 Grounding measures
This chapter of GB4736.1-1998 is applicable. 28 Grounding and connection
This chapter of GB4706.11996 is applicable. GB 4706.68-2003/1E4: 60335-2-95,159829 phase distance, electrical insulator and insulation distance GB4735.1-1098 are applicable. 30
Heat resistance, flame resistance and electrical insulator resistance
6B4706.12 In addition to the content specified, the following passage: 30.2.2, this content is not applicable.
31 Rust prevention
"B4735.1-18, except for the following memory, this clause is applicable to increase the reverse customer,
For components installed outdoors, the gasket with a grade of 2 in TFC35R-2 needs to be tested and checked for its qualification. Before the test, use a Zerong exhaust needle to measure the coating. The steel needle The end product has a 40\ dimensional angle and a tip radius of (.25mm). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of inrm/min to the surface of the device. Five scratches are made. The interval between the scratches must be at least 2mm and the interval between the scratches must be at least 2mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. The provisions of this chapter of GB/70,1-19 for radiation, toxicity and similar hazards are applicable. 8. Sectional doors with high guide rails for safety and comfort. Sectional doors with high guide rails. Figure 131. FA 4706.68—2003/ICC 60335-2-95:1998 Single-board door with annual business and navy style
Water lifting door
Special curtain door
Examples of various car single doorsPads with a grade 2 rating in TFC35R-2 must be tested to check their eligibility. Before testing, use a Zerong needle to scratch the coating. The end of the steel needle is 40° in angular shape and the radius between its tips is (.25mm2). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of 10/inrm/min on the surface of the steel needle. Five scratches are made. The interval between the scratches must be at least 1mm and the interval between the scratches must be at least 1mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. This chapter of GB/70,1-19 shall apply. 8. Sectional doors with high guide rails for safety and security. Figure 131. FA 4706.68-2003/ICC 60335-2-95:1998 Single-game door with business and navy style
Water rising door
Special curtain door
Examples of various car single doorsPads with a grade 2 rating in TFC35R-2 must be tested to check their eligibility. Before testing, use a Zerong needle to scratch the coating. The end of the steel needle is 40° in angular shape and the radius between its tips is (.25mm2). The steel needle can be placed against an appropriate load so that the load applied in the axial direction is 10-4. The steel needle is pushed with an extension of 10/inrm/min on the surface of the steel needle. Five scratches are made. The interval between the scratches must be at least 1mm and the interval between the scratches must be at least 1mm. After the test, the device should not be damaged to the extent that it complies with the standard, especially without the first and second sections. The layer shall not be broken or projected from the metal surface. This chapter of GB/70,1-19 shall apply. 8. Sectional doors with high guide rails for safety and security. Figure 131. FA 4706.68-2003/ICC 60335-2-95:1998 Single-game door with business and navy style
Water rising door
Special curtain door
Examples of various car single doors
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.