title>Designation of thermal spraying coatings - GB/T 12607-2003 - Chinese standardNet - bzxz.net
Home > GB > Designation of thermal spraying coatings
Designation of thermal spraying coatings

Basic Information

Standard ID: GB/T 12607-2003

Standard Name:Designation of thermal spraying coatings

Chinese Name: 热喷涂涂层命名方法

Standard category:National Standard (GB)

state:Abolished

Date of Release1990-01-02

Date of Implementation:2004-05-01

Date of Expiration:2007-09-29

standard classification number

Standard ICS number:Mechanical manufacturing>>Surface treatment and coating>>25.220.20 Surface treatment

Standard Classification Number:Comprehensive>>Basic Standards>>A29 Material Protection

associated standards

alternative situation:GB/T 12607-1990; adjusted to JB/T 10580-2006

Publication information

publishing house:China Standards Press

ISBN:155066.1-20461

Publication date:2004-04-09

other information

Release date:1990-12-18

Review date:2004-10-14

Drafting unit:Wuhan Institute of Materials Protection

Focal point unit:National Technical Committee for Standardization of Metallic and Non-metallic Coverings

Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China

competent authority:China Machinery Industry Federation

Introduction to standards:

This standard specifies the naming method of thermal spray coatings. This standard applies to the marking of thermal spray coatings. GB/T 12607-2003 Nomenclature of thermal spray coatings GB/T12607-2003 Standard download decompression password: www.bzxz.net
This standard specifies the naming method of thermal spray coatings. This standard applies to the marking of thermal spray coatings.


Some standard content:

GB/I12607—2003
This standard refers to K11eC730% heat-resistant coating. The following changes have been made to the standard 1/T126u?SC:
The types of coating processes have been simplified, and only 7GB/=187192:2. In addition to the terminology and classification, the existing thermal spraying process methods have been listed:
The marking method of the flow layer material has been changed, and the relevant environmental marking method of the standard has been adopted: This standard is proposed by the China Machinery Industry Federation, and this standard will be submitted to the national standardization and technical reform department for unified management. The standard is difficult to start, and the material protection research is mainly for discussion: Hong Shengdanjiang to Zigang. Scope
Nomenclature of thermal spray coatings
This standard now defines the naming method of thermal spray coatings, and the standard is used for the marking of thermal spray coatings
2 Normative references
GH/T 12607—2003
The following clauses are referenced by this standard. H is a referenced document whose subsequent revisions are not applicable to this standard. However, parties who have agreed to this standard are encouraged to use the latest versions of these documents. There are no outdated referenced documents, which are the latest versions of this standard. /T156—2333 Heat-treated polyester wood: composition and supply Technical Specifications 5011232:2029M0GB/T13606-2333 Classification and Supply Technical Specification for Wire, Rod and Core for Hot-drying and Flame-retardant Coating (SC) 1/919:2001, MO13)
GBT1R71S.2302 Terminology and Classification 014017:1993.M)
3 Nomenclature of Thermal Spray Coatings
3.1 General
The name of the thermal spray coating is based on the use of the components of the coating. The meaning of each part is as follows: 3.2 Thermal spraying code
Coating material mark
Thermal spraying process batch number
Substrate pretreatment code and
Thermal spraying code is represented by the English letter "TrmlSyir" of thermal spraying. 3.3 Substrate pretreatment method code
Substrate treatment method is represented by the same table, and the corresponding effect code of each pretreatment method is shown in the table. If one or more pretreatment methods are used, the effect code is represented by the order of the treatment, and the numbers are connected by "".
Table 1 Code for substrate surface pretreatment method
Substrate surface treatment method
Purification
Thermal spraying process code
Machining
Chemical etching
The technical spectrum of various thermal spraying processes can be found in GB/T9719-2002 "Thermal Spraying Process, Classification 3". Thermal
GB/I12607-2033
Thermal Spraying Process Code: 1. The English name of the process and the corresponding code are indicated by two English letters. Table 2 Thermal spraying process code
Hot paint process
Deep cutting
Iron smoke
Strict fire limit
Russian flame tea
Production of large quality road
Visual decoration
Atmospheric and other sub-warming flame
Controllable air pump and other sub-items except
Source special changed spraying
3.5 Cold layer material mark
Material layer material mark:
I Mail er-las.l. rpneyitg
Wine fntir ay:raying
Rud flame srr.yiny.
Poador -lenk apre yir i
Hizh velniry tlamc sprey ng.12rtr.natinn sataying.
are gayinz
Pleeme sorayirg ir git
Plasmz eprryirzin chomrrs
L.juu:d stelized rlasine sprgy:ng.aser spryvihg
The machine wood materials are marked with the material number in Chapter 3 of GT:-200, and the material number in Chapter 3.2 of GB/T25082003 is used as the identification. 3.6 Code for post-processing method
The post-processing method is represented by Arabic numerals, and the virtual code for each post-processing method is as follows. If two or more treatments are used, the correct treatment is of course, according to the order of concentration, the corresponding treatment numbers in the table are connected with ".
Product treatment method will
have a combination of coating or step removal marking method 3.7
Coating stone treatment method code
Chemical treatment www.bzxz.net
For multiple layers of step removal, use the above method to mark each layer of coating, and The names of the following are changed to slashes. Example 1: Using high-pressure plasma spraying to treat the surface of the substrate with high-quality sand M, the material content is 3.2 ALS9.5, and the thermal spray coating is named S322. Example: Using non-gas plasma spraying, the substrate surface is pre-treated with high-quality sand, and the material content is 3.2 ALS9.5. The thermal spray coating is named S322. 5% base powder is not natural material with a small amount of material code of 2.3, the surface layer contains 47% T15, the future material will be, after suction coating, the thermal spray coating will be machine-processed, 1PA.1/PA12.3-3 Example 3:
adopts pressurized powder fire box, except for the surface treatment, the coating material number is .1U: B5: self-penetrating gold grid end material. Chengyu production input quantity treatment state thermal coating allowable rate: 15 risk, 104
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.