This standard specifies the terms and definitions, classification, requirements, test and inspection methods, acceptance rules, marking, packaging, transportation, storage and safety measures, as well as environmental protection and sanitation requirements for holographic anti-counterfeiting products. This standard applies to holographic anti-counterfeiting products, including holographic anti-counterfeiting labels, holographic anti-counterfeiting films, holographic anti-counterfeiting paper, holographic anti-counterfeiting strips (lines), etc. GB/T 17000-2009 General Technical Conditions for Holographic Anti-Counterfeiting Products GB/T17000-2009 Standard Download Decompression Password: www.bzxz.net
This standard specifies the terms and definitions, classification, requirements, test and inspection methods, acceptance rules, marking, packaging, transportation, storage and safety measures, as well as environmental protection and sanitation requirements for holographic anti-counterfeiting products. This standard applies to holographic anti-counterfeiting products, including holographic anti-counterfeiting labels, holographic anti-counterfeiting films, holographic anti-counterfeiting paper, holographic anti-counterfeiting strips (lines), etc.
Foreword
　　This standard replaces GB/T 17000-1997 "General Technical Requirements for Anti-Counterfeiting Holographic Products".
Compared with GB/T 17000-1997, the main changes in this standard are as follows:
———The name of the standard has been revised from the original "General Technical Requirements for Anti-Counterfeiting Holographic Products" to "General Technical Requirements for Holographic Anti-Counterfeiting Products".
———The scope of the standard has been modified. The scope of the standard has been modified to: applicable to holographic anti-counterfeiting products, including holographic anti-counterfeiting labels, holographic anti-counterfeiting films,
holographic anti-counterfeiting papers, holographic anti-counterfeiting strips (lines), etc. (see Chapter 1).
———"Definitions" has been revised to "Terms and Definitions", some terms have been modified, and 21 new terms have been added (see Chapter 3).
———The classification content of holographic technology has been modified, and the classification methods of "classification by product type" and "classification by design and plate holographic technology" have been established
(see Chapter 4).
———The contents of "anti-counterfeiting level", "anti-counterfeiting strength" and "product technical requirements" have been revised to the
requirements of "anti-counterfeiting characteristics" and "product quality", that is, the three chapters in the 1997 version of the standard have been merged and uniformly revised into "requirements", focusing on the research and formulation of the "anti-counterfeiting characteristics"
content (Chapter 5 "Anti-counterfeiting level", Chapter 6 "Anti-counterfeiting strength" and Chapter 7 "Product technical requirements" of the 1997 version, Chapter 5
"Requirements" of this version).
———The product test method has been revised to "Test and inspection methods" (Chapter 8 of the 1997 version, Chapter 6 of this version).
———Revised the product inspection rules and revised them into “Acceptance Rules” (Chapter 9 “Product Inspection Rules” of the 1997 edition, Chapter 7
“Acceptance Rules” of this edition).
———Revised the contents of “Safety Measures” and “Marking, Packaging, Transportation, Storage”, and merged the two chapters into “Marking, Packaging, Transportation, Storage
and Safety Measures” (Chapter 10 “Safety Measures” and Chapter 11 “Marking, Packaging, Transportation, Storage” of the 1997 edition,
Chapter 8 “Marking, Packaging, Transportation, Storage and Safety Measures” of this edition).
———Added environmental protection and hygiene requirements (see Chapter 9).
———Added normative Appendix A “Explicit Holographic Anti-Counterfeiting Identification Features and Verification Methods”.
———Added normative Appendix B “Invisible Holographic Anti-Counterfeiting Identification Features and Verification Methods”.
———Add normative Appendix C "Test method for diffraction efficiency and signal-to-noise ratio of rainbow holographic anti-counterfeiting products".
———Add normative Appendix D "Test method for diffraction efficiency of dot matrix holographic anti-counterfeiting products".
Appendix A, Appendix B, Appendix C and Appendix D of this standard are normative appendices.
This standard is proposed and managed by the National Anti-Counterfeiting Standardization Technical Committee (SAC/TC218).
Drafting units of this standard: Northern Nine Star Holographic Products Co., Ltd., National Anti-Counterfeiting Product Quality Supervision and Inspection Center, Shenzhen University Reflective Materials
Factory, Shenzhen Nine Star Printing and Packaging Group Co., Ltd., Guangdong Southeast Film Technology Co., Ltd., Beijing Sanyou Anti-Counterfeiting Trademark Printing Co., Ltd., China
Banknote Printing and Minting Corporation, China Banknote Printing and Minting Corporation Special Anti-Counterfeiting Technology Company, National Anti-Counterfeiting Engineering Technology Research Center.
The drafters of this standard are: Wang Zhenliang, Liu Kefu, Wang Xiaobing, Jiang Shuqing, Chen Songqing, Ha Liuzhu, Cheng Haiyan, Pei Wen, Luan Xin, Wang Xiaoli,
Chen Rujun.
The previous versions of the standards replaced by this standard are:
———GB/T 17000-1997.
The clauses in the following documents become the clauses of this standard through reference in this standard. For any dated referenced document, all subsequent
amendments (excluding errata) or revisions are not applicable to this standard. However, the parties to the agreement based on this standard are encouraged to study
whether the latest versions of these documents can be used. For any undated referenced document, the latest version is applicable to this standard.
GB/T2828.1 Sampling procedures for inspection by attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL)
(GB/T2828.1-2003, ISO2859-1:1999, IDT)
GB/T2829 Sampling procedures and tables for periodic inspection by attributes (applicable to inspection of process stability)
GB/T18733-2002 Anti-counterfeiting holographic paper
GB/T18734-2002 Anti-counterfeiting holographic hot stamping foil
GB/T19425-2003 General technical requirements for anti-counterfeiting technology products
GB/T22258-2008 General technical requirements for anti-counterfeiting labels
GB/T23808-2009 Holographic anti-counterfeiting film

ICS 03. 120.99
National Standard of the People's Republic of China
GB/T17000--2009
Replaces GB/T17000--1997
Uniform technical requirements of holographic anti-counterfeiting products
products2009-05-06 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
2009-11-01 Implementation
Normative references
Terms and definitions
Test and inspection methods
Acceptance rules
Marking, packaging, transportation, storage and safety measures 9 Environmental protection, hygiene
Appendix A (Normative Appendix) Overt holographic anti-counterfeiting identification features and verification methods Appendix B (Normative Appendix)
Invisible holographic anti-counterfeiting identification features and verification methods Appendix C (Normative Appendix)
Test method for diffraction efficiency and signal-to-noise ratio of rainbow holographic anti-counterfeiting products Appendix D (Normative Appendix) Test method for diffraction efficiency of dot matrix holographic anti-counterfeiting products. Hepin Partner Network htt
CB/T17000--2009
This standard replaces GB/T17000--1997 "General Technical Conditions for Anti-Counterfeiting Holographic Products". The main changes of this standard compared with GB/T17000-1997 are as follows: GB/T17000-2009
The standard name is revised from the original "General Technical Conditions for Anti-Counterfeiting Holographic Products" to "General Technical Conditions for Holographic Anti-Counterfeiting Products". The scope of the standard is modified. The scope of the standard is modified to: Applicable to holographic anti-counterfeiting products, including holographic anti-counterfeiting labels, holographic anti-counterfeiting films, holographic anti-counterfeiting papers, holographic anti-counterfeiting strips (lines), etc. (see Chapter 1). Revised "Definition" to "Terms and Definitions", modified some terms, and added 21 new terms (see Chapter 3). Revised "Classification of Holographic Technology" to establish the classification methods of "Classification by Product Type" and "Classification by Design and Platemaking Holographic Technology" (see Chapter 4).
- Revised the contents of "Anti-Counterfeiting Level", "Anti-Counterfeiting Strength" and "Product Technical Requirements" to "Anti-Counterfeiting Characteristics" and "Product Quality". That is, the two chapters in the 1997 version of the standard were merged and uniformly revised to "Requirements", focusing on the research and formulation of "Anti-Counterfeiting Characteristics" (Chapter 5 "Anti-Counterfeiting Level", Chapter 6 "Anti-Counterfeiting Strength" and Chapter 7 "Product Technical Requirements" of the 1997 version, Chapter 5 "Requirements" of this version).
Revised the product test method to "Test and Inspection Method" (Chapter 8 of the 1997 version, Chapter 6 of this version). Revised the product inspection rules to "Acceptance Rules" (19 Chapter 9 of the 1997 edition, "Product Inspection Rules", is now Chapter 7 of this edition, "Acceptance Rules".
- Revise the contents of "Safety Measures" and "Marking, Packaging, Transportation, Storage", and merge the two chapters into "Marking, Packaging, Transportation, Storage and Safety Measures". Chapter 10 of the 1997 edition, "Safety Measures", Chapter 11 of the 1997 edition, is now Chapter 8 of this edition, "Marking, Packaging, Transportation, Storage and Safety Measures"). Add environmental protection and hygiene requirements (see Chapter 9). - Add normative Appendix A "Explicit Holographic Anti-Counterfeiting Identification Features and Verification Methods" - Add normative Appendix B "Invisible Holographic Anti-Counterfeiting Identification Features and Verification Methods". Add normative appendix (\Test method for diffraction efficiency and signal-to-noise ratio of rainbow holographic anti-counterfeiting products". - Add normative Appendix D "Test method for retrieval efficiency of dot matrix holographic anti-counterfeiting products". Appendices A, B, C and D of this standard are normative appendices. This standard is prepared by the National Anti-Counterfeiting Standardization Technical Committee (SAC/TC 218) The drafting units of this standard are: Northern Nine Star Holographic Products Co., Ltd., National Anti-counterfeiting Product Quality Supervision and Inspection Center, Shenzhen Renxue Reflective Materials Factory, Shenzhen Erxing Printing and Packaging Group Co., Ltd., Guangdong Southeast Film Technology Co., Ltd., Beijing Lanyou Anti-counterfeiting Trademark Printing Co., Ltd., China Banknote Printing and Minting Corporation, China Banknote Printing and Minting Corporation Special Anti-counterfeiting Technology Company. National Anti-counterfeiting Engineering Technology Research Center. Drafters of this standard: Wang Zhenliang, Liu Keda, Wang Xiaobing, Jiang Shuqing, Chen Songqing, Ha Liuzhu, Cheng Haiyan, Zhuang Wen, Luan Xin, Xia Xiaoli, Chen Rujun.
The previous versions of the standards replaced by this standard are -GB/1170001997.
ht
1 Scope
General technical conditions for holographic anti-counterfeiting products
GB/T 17000—2009
This standard specifies the terms and definitions, classification, requirements, test and inspection methods, acceptance rules, marking, packaging, transportation, storage and safety measures, as well as environmental protection and safety requirements for holographic anti-counterfeiting products. This standard applies to holographic anti-counterfeiting products, including holographic anti-counterfeiting labels, holographic anti-counterfeiting films, holographic anti-counterfeiting papers, holographic anti-counterfeiting strips (lines), etc. 2 Normative references
The clauses in the following documents become clauses of this standard through reference in this standard. For all referenced documents with a notified date, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. The parties who reach an agreement based on this standard shall study whether the latest versions of these documents can be used. For any undated referenced documents, the latest versions shall apply to this standard. (FB/T2828.1 Sampling inspection procedures for attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) (GR/T2828.1-2003, ISO2859-1:1999, IDT) GB/T2829 Sampling procedures and tables for periodic inspection by attributes (applicable to inspection of process stability) GB/T187332002 Anti-counterfeiting holographic paper
GB/T 18734—2002
GB/T 19425—2003
GB/T 22258—2008
GB/T238082009
3 Terms and Definitions
Anti-Counterfeiting Holographic Foil
General Technical Requirements for Anti-Counterfeiting Technology Products
General Technical Requirements for Anti-Counterfeiting Labels
Holographic Anti-Counterfeiting Film
The following terms and definitions apply to this standard. 3.1
Holographic Anti-Counterfeiting ProductHolographic anti-counterfeiting product is an anti-counterfeiting product manufactured using holographic anti-counterfeiting technology, which can objectively prevent counterfeiting, is not easily imitated or copied, and can accurately identify the authenticity within a certain range.
Embossed hologram
embossed hologram
A hologram obtained by transferring the holographic interference fringes in the form of a relief structure onto a substrate (plastic film, paper or other materials) through a molding process.
Volume reflection hologram volumercfteclionhologram Lippmann hologram A hologram obtained by using reflection holographic illumination technology and corresponding photosensitive materials (such as photopolymers, silver salt materials, etc.) as recording media.
Dot-matrix hologram Computer dot-matrix hologram Computer dot-matrixholagram Dot-matrix hologram is composed of a dot matrix arranged in a dot grating. The arrangement of the grating dot matrix, the stripe pattern and density of the dot grating are controlled by a computer to obtain different visual effects. 1
Hepin Partner Network ht
GB/T 170002009
Holographic anti-counterfeiting label Holographic anti-counterfeiting label is an anti-counterfeiting label made using optical holographic technology. 3.6
Holographic anti-counterfeiting film Holographic anti-counterfeiting film 3.7
Holographic anti-counterfeiting film is a holographic anti-counterfeiting film with a reflective coating. Common coatings include metal coating and non-metal coating. Holographic anti-counterfeiting films with metal diamond coating are usually called aluminum-coated holographic anti-counterfeiting films, and holographic anti-counterfeiting films with non-metal coating are usually called dielectric gold-coated holographic anti-counterfeiting films.8
No-coated holographic anti-counterfeiting filmHolographic anti-counterfeiting film without reflective coating.
Transfer holographic anti-counterfeiting filmTransfer holographic anti-counterfeiting filmHolographic anti-counterfeiting film that can transfer the holographic information to the target object by heat transfer or cold transfer3. 10
Non-transfer holographic anti-counterfeiting filmNon-transfer holographic anti-counterfeiting filmHolographic anti-counterfeiting film that cannot transfer the holographic information to the target object3. 11
Transparent holographic anti-counterfeiting filmTransparent holographic anti-counterfeiting filmAnti-counterfeiting film with a partially or completely transparent holographic anti-counterfeiting pattern. 3.12
Heat-shrinkable holographic anti-counterfeiting filmHeat-shrinkable hnlographic anti-counterfeiting filmHolographic anti-counterfeiting film with heat-shrinkable plastic film as the base material. 3.13
Hot stamping holographic anti-counterfeiting film holographic anti-counterfeiting hot stanping film hulographic tili-caunterfeiting hot stamping foil is a holographic hot stamping product with anti-counterfeiting function made of plastic film as the base material through coating, film plating, molding and rolling processes. 3. 14
Laminating holographic anti-counterfeiting film is a holographic anti-counterfeiting product that uses plastic film as the base material and can be completely laminated to paper materials or multiple layers. 3.15
Holographic anti-counterfeiting paper is a holographic anti-counterfeiting product that uses paper as the base material through coating, molding and other processes or transfer and other processes. 3.16
Laminating filmholographic anti-counterfeiting paper is a holographic anti-counterfeiting product made by completely laminating the composite holographic anti-counterfeiting film onto paper material: 3. 17
Helographic anti-counterfeiting strip is a holographic anti-counterfeiting strip. Holographic anti-counterfeiting thread is a holographic anti-counterfeiting product made of holographic anti-counterfeiting film and processed into strips or lines by slitting. 2
Product partnership area
Black spot
Dark spot on the hologram caused by defects on the embossing roller or embossing working plate. 3.19
Yellow spot
Slightly yellowed spot on the aluminum coating.
Pin hules
During vacuum coating, defects in the coating caused by various reasons. 3.21
Plate gap
The gap in the effective layout of the molded product caused by the splicing of the molded working plate. 3.22
Water stains
The marks caused by physical or chemical factors during the production process of the hologram master due to improper handling. 3.23
scratch
The scratch marks that affect the effective layout of the product. 3.24
Color pattern positioning errorColor pattern positioning errorThe deviation of the positioning of different color images with a common boundary. 3.25
Cutting center deviation
Cutting center error
The deviation between the center of the pattern and the center of the die-cutting geometry. 3.26
Signal to noise ratioThe ratio of the signal intensity of the image reconstructed in the diffracted light to the noise intensity. 3.27
Dirfraction efficiencyThe ratio of the signal intensity of the image reconstructed in the diffracted light to the incident light intensity. 3.28
Deflective error
The difference between the lengths of the two diagonals of a holographic security paper. 4 Classification
4.1 Classification by product type
4. 1. 1 Holographic anti-counterfeiting label
Embossed holographic anti-counterfeiting label refers to pasted holographic anti-counterfeiting label and transferred holographic anti-counterfeiting label; a)
b) volumetric reflective holographic anti-counterfeiting label.
4.1.2 Holographic anti-counterfeiting film
4.1.2.1 According to the coating, it can be divided into:
a) Coated holographic anti-counterfeiting film, which refers to metal-coated holographic anti-counterfeiting film and dielectric-coated holographic anti-counterfeiting film; b) Uncoated holographic anti-counterfeiting film, which refers to uncoated transparent holographic anti-counterfeiting film. 2
According to the usage, it is divided into:
Transfer type holographic anti-counterfeiting film refers to hot stamping holographic anti-counterfeiting film (foil), cold transfer holographic anti-counterfeiting film; non-transfer type holographic anti-counterfeiting film refers to composite holographic anti-counterfeiting film, heat shrink holographic anti-counterfeiting film,)
4.1.3 Holographic anti-counterfeiting paper
Transfer type holographic anti-counterfeiting paper;
b) Non-transfer type holographic anti-counterfeiting paper refers to laminated holographic anti-counterfeiting paper, etc. Holographic anti-counterfeiting strips (threads)
a) Holographic anti-counterfeiting pull strips (threads), used for the sealing of plastic film packaging, such as cigarette packaging, etc.; holographic anti-counterfeiting sealing strips (threads), twisted with threads of other materials, used for sewing the sealing of bag packaging; b)
Holographic anti-counterfeiting security strips (threads), holographic strips or threads combined with the subject matter. c)
Classification of holographic anti-counterfeiting technology by design and plate making
Design and plate making holographic anti-counterfeiting technology generally includes the following categories: rainbow holographic anti-counterfeiting technology;
b) Computational holographic anti-counterfeiting technology;
Computer-assisted holographic anti-counterfeiting technology;
d) Volumetric reflection holographic anti-counterfeiting technology;
Optical information processing and optical transformation holographic anti-counterfeiting technology (including various optical encryption): f)
Color control and multi-channel synthetic holographic anti-counterfeiting technology; pulse holographic anti-counterfeiting technology
5 Requirements
5.1 Anti-counterfeiting characteristics
5,1,1 Anti-counterfeiting strength
5.1.1. 1 Factors constituting anti-counterfeiting strength
The anti-counterfeiting strength of holographic anti-counterfeiting products is composed of four factors: the number of anti-counterfeiting identification features, the number of anti-counterfeiting technology exclusivity, the difficulty of manufacture and the size of the imitation cost. The conditions and requirements that each factor should meet are as follows: the number of exclusive anti-counterfeiting technology in the anti-counterfeiting strength of holographic anti-counterfeiting products, the difficulty of imitation, and the size of the cost of damage are in accordance with the provisions of 5. ］ in a)
GB/T 19425-2003. b) The number of anti-counterfeiting identification features in the anti-counterfeiting strength of holographic anti-counterfeiting products should be no less than (including) two. The classification and verification of anti-counterfeiting identification features are shown in 5.1.1.2 and 5.1.1.3, 5.1.1.2 Classification of anti-counterfeiting identification features of holographic anti-counterfeiting products 5.1.1.2.1 The anti-counterfeiting identification features of holographic anti-counterfeiting products are divided into explicit holographic anti-counterfeiting identification features and personal holographic anti-counterfeiting identification features: 5.1.1.2.2 The explicit holographic anti-counterfeiting identification features can be identified by the senses without the help of instruments. Generally include the following categories: a) Rainbow holography;
Dot matrix holography;
Volume reflection holography;
Optical lens effect;
Isotopic anomaly;
Three-dimensional background:
Multi-channel synthetic holography;
h) Achromatic holography.
5.1.1.2.3 Hidden holographic anti-counterfeiting identification features should be accurately identified with the help of tools or instruments. -Generally include the following categories a) Moiré fringes:
ht
b) Laser reproduction;
Micrographics;
Machine-readable features.
Anti-counterfeiting identification features and verification of holographic anti-counterfeiting products. For explicit gold interest anti-counterfeiting identification features and verification methods, see Appendix A: a
For hidden holographic anti-counterfeiting identification features and verification methods, see Appendix 13. b)
5.1.2 Uniqueness of identity
a) The non-transferability rate of residual anti-counterfeiting labels should not be less than 90%. b) The uniqueness of holographic anti-counterfeiting films, holographic anti-counterfeiting papers, and holographic anti-counterfeiting strips (lines) shall be declared by the enterprise. 5.1.3 Stability period
The stability period of anti-counterfeiting identification features shall comply with the provisions of 5.3 of GB/T19425-2003. 5.1.4 Recognition performance
Explicit identification features can be identified by sense organs without the aid of instruments. a)
Recessive identification features can only be accurately identified with the aid of tools or instruments. ) The recognition performance shall meet the requirements of Table 4 of GB/T19425-2003. 5.1.5 Adaptability to use
GB/T 17000-—2009
Holographic anti-counterfeiting products shall indicate the scope of use or the type of the subject matter, and the adaptability to use shall be able to meet the requirements of the subject matter during its stability period. The stability period is specified in the specific product standards or contracts. 5.1.6 Use environment
The anti-counterfeiting performance of holographic anti-counterfeiting products should be able to meet the requirements of normal use environment during its stability period, or the user should ask the manufacturer for specific requirements in the order contract.
5.1.7 Technical security and confidentiality
a) In the design and production process, the computer graphic files, ink drawings, mask plates and nickel plates used for holographic plate making should formulate corresponding technical security and confidentiality management systems;
b) Test products, defective products, etc. should be destroyed in time, and the destruction records should be kept; c) The production environment should meet the closed management requirements. 5.1.8 Safety period
According to the provisions of 5.8 in GB/T 19425-2003. 5.2 Product Quality
5.2.1 Appearance Quality
5.2.1.1 The appearance quality of the holographic anti-counterfeiting label shall comply with the provisions of Table 3 in CB/T 22258-2008. The unevenness of the end surface of the coil shall not exceed 0.5 mm, the coil shall be appropriately tight, and the coil shall not fall apart after being transported for more than 5 times. 5.2.1.2 The appearance quality of the holographic anti-counterfeiting film shall comply with the provisions of the table in GB/T23808-2009. 5.2.1.3 The appearance quality of holographic security paper shall comply with the provisions of Table 1 in (F13/T18733-2002, and the appearance quality of laminated holographic security paper shall also comply with the provisions of Table 1.
Table 1 Appearance quality of laminated holographic security paper
Item name
Surface quality
Cutting rough edges
Quality requirements
The varnish coating shall be uniform and effective, without air pool points, white spots and fog, and the gloss shall be obvious. The marks and spots are slight, but they should not be obvious when viewed horizontally and do not affect the subsequent processing and use performance. Slight, but they should not be obvious when viewed horizontally and do not affect the subsequent processing and use performance. Slight, but they should not be obvious when viewed horizontally and do not affect the subsequent processing and use performance. GB/T 17000--2009
Project name
Black spots, bright spots or pitting
Black or light stripes
Table 1 (continued)
Quality requirements
Black spots, microdots or pitting not larger than 1mm, less than or equal to 8 in each grid (less than or equal to 5 in the main part), and not densely distributed
Obvious black or light stripes are less than or equal to 1 in each grid, and the rest are allowed to be inconspicuous at eye level. Bubbles with a diameter of no more than 3mm are less than or equal to 3 in each grid, not allowed. There are dense filter spots Although there are dense fine scratches, the half-pick should not be obvious 5.2.1.4 The appearance quality requirements of the holographic anti-counterfeiting strip (line) shall comply with the provisions of Table 2. Table 2 Appearance quality of holographic anti-counterfeiting strip (line) Item Name
Surface quality
Image quality
5.2.2 Product specifications
Quality requirements
The surface is flat, without wrinkles, ribs, and no systematic scratches and concave and convex points that affect the quality of use. The image is clear, the color is distinct, and the brightness is uniform. 5.2.2.1 Holographic anti-counterfeiting mark The die-cutting center deviation shall comply with the provisions of Table 6 in GB/T22258-2008. 5.2.2.2 The product specifications of holographic anti-counterfeiting film shall comply with the provisions of Table 2 in GB/T23808--2009. 5.2.2.3 The product specifications of holographic anti-counterfeiting paper shall comply with the provisions of Table 2 in GB/T18733:2002, and its deflection rate shall be less than or equal to 3mm. 5.2.2.4 The relative error of the line width of the holographic anti-counterfeiting strip (line) product shall be less than or equal to 10%. 5.2.3 Product characteristic indicators
5.2.3.1 Holographic anti-counterfeiting mark The product characteristic indexes shall be in accordance with the provisions of Table 7 of GB/T22258-2008. 5.2.3.2 The characteristic indexes of the coated holographic anti-counterfeiting film shall be in accordance with the provisions of Table 3 of GB/T23808-2009, especially the characteristic indexes of the coated holographic anti-counterfeiting film shall be in accordance with the provisions of 5.2.3.2 of GI3/I23808-2009. 5.2.3.3 The characteristic indexes of holographic anti-counterfeiting paper shall be in accordance with the provisions of Table 3 of GB/T18733-2002. The degree of film-paper composite of the laminated holographic anti-counterfeiting paper shall be such that the film shall be firmly laminated on the paper. 5.2.3.4 The diffraction efficiency of the holographic anti-counterfeiting strip (line) shall be greater than or equal to 5%. 6 Test and inspection methods
6. 1 Test requirements
6. 1. 1 Test environment
Centrifugal force: 23℃±5℃; relative humidity: 30%～65%. 6.1,2 Sample collection
Holographic anti-counterfeiting film shall be carried out in accordance with the provisions of 7.1.2 of GB/T18734-2002; holographic anti-counterfeiting paper shall be carried out in accordance with the provisions of 7.1.2 of GB3/T18733-2002; the samples of other products shall be taken as specified in the specific product standards or contracts. 6.1.3 Sample pretreatment
The samples shall be placed for no less than 8 hours under the experimental environment conditions. 6.2 Anti-counterfeiting characteristics
6.2.1 Anti-counterfeiting strength
According to the provisions of 6.1 of GB/T19125-2003, the number and content of holographic anti-counterfeiting identification features shall be verified according to the verification methods provided in Appendix A and Appendix B; the items not included in Appendix A can be verified according to the inspection methods provided by the manufacturer: 6.2.2 Identity
6.2.2.1 Non-transferability of holographic anti-counterfeiting logo The sample shall be pasted on the corresponding target object. If the target object is not specified, the sample shall be pasted on 80g offset paper and placed at room temperature for 6
combination product partner network htt
GB/T17000--2009
24h before peeling off inspection. After peeling off, the effective pattern area of ​​the sample destroyed shall not be less than 60%, and the sample cannot be used again. 6.2.2.2 The identity of holographic anti-counterfeiting film, holographic anti-counterfeiting paper and holographic anti-counterfeiting strip (line) shall be verified by daily testing or with the help of special instruments based on the identification features of the identity provided by the manufacturer.
6.2.3 Stability period
Performed in accordance with the relevant test methods provided by the manufacturer. 6.2.4 Identification performance
Performed in accordance with the provisions of 6.4 of GB/T19125-2003. 6.2.5 Adaptability to use
Performed in accordance with the test methods specified in the contract between the manufacturer and the user according to the use scope of the batch of products indicated by the manufacturer. 6.2.6 Requirements for use environment
Performed in accordance with the test methods specified in the contract between the manufacturer and the user according to the use environment proposed by the manufacturer. 6.2.7 Technical security and confidentiality
Performed in accordance with the provisions of 6.7 of GB/T19425--2003. 6.2.8 Safety period
According to the provisions of 6.8 in GB/T19425-2003. 6.3 Product quality
6.3.1 Appearance quality
Put the sample on a flat glass. Set a 60W tungsten light source 0.8m away from the sample and illuminate it at the reproduction angle. The observer uses a magnifying glass, a reading microscope and related testing tools to observe or measure. 6.3.2 Product specifications
6.3.2.1 The die-cutting center deviation of the holographic anti-counterfeiting mark shall be carried out in accordance with the provisions of 6.10 in GB/T22258--2008. 6.3.2.2 The product specifications of the holographic anti-counterfeiting film shall be carried out in accordance with the provisions of 6.3.2 in GB/T23808-2009. 6.3.2.3 The product specifications of the holographic anti-counterfeiting paper shall be carried out in accordance with the provisions of 7.3 in G3/T18733-2002. Lay the flat sheet of holographic security paper flat and use a measuring tool with an accuracy of not less than 0.01 nt to directly measure the skewness. 6.3.2.4 The line width error of the holographic security strip (line) should be directly measured using a measuring tool with a graduation value of 0.01mm. 6.3.3 Characteristic Indicators
The retrieval efficiency and signal-to-noise ratio of the holographic security mark shall be in accordance with the provisions of Appendix C or Appendix D, and other characteristic indicators shall be in accordance with the provisions of 6.3.3.1
6.1.1 of GB/T22258-2008. 6.3. 3.2 The diffraction efficiency and signal-to-noise ratio of the holographic anti-counterfeiting film shall be in accordance with the provisions of Appendix or Appendix 1, and other characteristic indicators shall be in accordance with the provisions of 6.3 in GB/T23808-2009. 6.3.3.3 The diffraction efficiency and signal-to-noise ratio of the holographic anti-counterfeiting paper shall be in accordance with the provisions of Appendix C or Appendix D, and other characteristic indicators shall be in accordance with the provisions of 7.4 in GB/T18733-2002. The film fiber composite degree of the laminated gold-cut paper shall be directly peeled off along its edge by hand.
6.3.3.4 The diffraction efficiency of the holographic anti-counterfeiting strip (line) shall be in accordance with the provisions of Appendix C. 7 Acceptance rules
7.1 Types of inspection
Inspection is divided into type inspection and factory inspection. 7.2 Type inspection
Type inspection shall be carried out in full accordance with the technical requirements specified in this standard, and relevant items of routine tests shall be added when necessary. Type inspection is required in the following situations:
a) When a new product or product is put into production;
Product Partner Network
GB/T 17000—2009
When there are major changes in materials, processes, and formulations, and the impact on product performance is assessed; b)
When assessing product quality stability during normal production, periodically or after accumulating a certain amount of production; c) When the product is resumed after a long period of suspension; d)
When there is a significant difference between the factory inspection result and the first type inspection result; e
[)When the national quality supervision agency proposes a type inspection requirement. 7.3 Factory Inspection
Factory inspection is conducted on a batch-by-batch basis. Factory inspection items include anti-counterfeiting strength (see 5.1.1) and appearance quality (see 5.2.1) product specifications (see 5.2.2), 7. 4 Sampling plan and qualified judgment
a) The sampling plan for F-inspection shall be carried out in accordance with the normal inspection one-time sampling plan with general inspection level II in (B/T2828.1). The qualified quality level (AQL) shall take different values ​​according to the nature of the defects on the inspection day. For the inspection items that may cause serious defects, the AQL value shall be 1.5, and for the inspection items with minor defects, the AQL value shall be 6.5. The sampling plan for type inspection shall be carried out in accordance with GB/T28294--normal inspection one-time sampling plan with general inspection level I. RQIb
According to the qualified judgment number and unqualified judgment number specified in the sampling plan, the qualification of each indicator shall be determined respectively. If they meet the requirements, the batch of products shall be determined to be qualified; otherwise, the batch of products shall be determined to be unqualified. 8 Marking, packaging, transportation, storage and safety measures 8.1 Marking
The following marks shall be on the outer packaging or product certificate when the product leaves the factory: a) Product name and number.
b) Product specifications, quantity, batch number.
Name and address of the manufacturer.
d) Date of production
e) Standard number and name of the product production.
g) Contents required by national laws, regulations and relevant policies. 8.2 Packaging
According to the provisions of 8.2 of GB/T 19425--2003. 8.3 Transportation
During transportation, it should be protected from sunlight and moisture, and should not be heavily pressed. It should not be mixed with chemicals and pollutants for shipment. It is not allowed to lower the product from a high place during transportation, and it should be strictly prevented from collision and scratches by vehicles.
8.4 Storage
It should be stored in a windproof, moisture-proof and fireproof warehouse. The air temperature and relative humidity in the warehouse should meet the storage requirements of holographic anti-counterfeiting products, and the storage period should ensure that the quality of holographic anti-counterfeiting products is not affected. 8.5 Safety measures
During the production, transportation, storage and other processes of holographic anti-counterfeiting products, enterprises should formulate safety and confidentiality measures and effectively implement 9 Environmental protection and hygiene
The production and sales of holographic anti-counterfeiting products should comply with the requirements of relevant national environmental protection and hygiene standards. 8
A. 1 Verification conditions
A.1.1 Light source
White light point light source.
A.1.2 Light source incident direction
Appendix A
(Normative Appendix)
Explicit holographic anti-counterfeiting identification features and verification methods Point light source is incident from above the sample at an angle, and the sample is observed in the normal direction. A.2 Anti-counterfeiting identification features of holograms
A.2.1 Rainbow remnant
A.2.1. 1 Multicolor (image plane) rainbow hologram
Different positions of the hologram in the image plane show different colors. A,2. 1. 2 Multicolor two-dimensional/three-dimensional images
Images with different depths of field show different colors. A.2. 1. 3 Three-dimensional hologramWww.bzxZ.net
Holograms are three-dimensional stereoscopic images.
A.2.1.4 True color
The two- or three-dimensional reconstructed image is similar to the color of the real object, which is called true color. A.2.2 Dot matrix hologram
A.2.2. 1 Radiation-contraction effect
When the viewing direction is changed, the hologram shows dynamic changes of radiation-contraction. A.2,2. 2 Rotation effect
When the viewing direction is changed, the hologram shows dynamic changes of plane rotation (such as fan shape). A.2.2.3 Two-dimensional super line holography
The fine super line pattern in the image plane presents a multi-color rainbow. A.2.2.4 Flowing effect
When the sample is moved or rotated, its holographic pattern has a flowing visual change. A.2.3 Volume reflection holography
A.2.3.1 Monochrome volume holography
GB/T 17000—2009
The volume reflection holography recorded with a single wavelength, the whole image is one color, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.3.2 True color volume reflection holography
The volume reflection holography recorded with multiple wavelengths, the holographic image is multiple colors, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.4 Optical lens effect
A.2.4.1 Concave and convex lenses
The holographic image presents a concave lens or convex lens effect. A.2.4.2 Clear code marking
Through the lens, you can see the deep text. 2.2.5 Isotopic anomalies
When the sample is rotated, different images and texts are successively seen at the same position. 9
Hepin Partner Network ht1 Marking
The following markings shall be on the outer packaging or product certificate when the product leaves the factory: a) Product name and number.
b) Product specifications, quantity, batch number.
Name and address of the manufacturer.
d) Production date
e) Standard number and name based on which the product is produced.
Production license number.
g) Contents required by national laws, regulations and relevant policies. 8.2 Packaging
According to the provisions of 8.2 of GB/T 19425--2003. 8.3 Transportation
During transportation, the product shall be protected from sunlight and moisture, shall not be heavily pressed, and shall not be shipped together with chemicals and polluted products. It is not allowed to lower the product from a high place during transportation, and it shall be strictly prevented from collision and scratches by vehicles.
8.4 Storage
The product shall be stored in a warehouse that is windproof, moistureproof and fireproof. The air temperature and relative humidity in the warehouse should meet the storage requirements of holographic anti-counterfeiting products, and the storage period should ensure that the quality of holographic anti-counterfeiting products is not affected. 8.5 Safety measures
During the production, transportation, storage and other processes of holographic anti-counterfeiting products, enterprises should formulate safety and confidentiality measures and effectively implement 9 Environmental protection and hygiene
The production and sales of holographic anti-counterfeiting products should comply with the requirements of relevant national environmental protection and hygiene standards. 8
A. 1 Verification conditions
A.1.1 Light source
White light point light source.
A.1.2 Light source incident direction
Appendix A
(Normative Appendix)
Explicit holographic anti-counterfeiting identification features and verification methods Point light source is tilted from above the sample and observed in the normal direction. A.2 Anti-counterfeiting identification features of holograms
A.2.1 Rainbow remnant
A.2.1. 1 Multicolor (image plane) rainbow hologram
Different positions of the hologram in the image plane show different colors. A,2. 1. 2 Multicolor two-dimensional/three-dimensional images
Images with different depths of field show different colors. A.2. 1. 3 Three-dimensional hologram
Holograms are three-dimensional stereoscopic images.
A.2.1.4 True color
The two- or three-dimensional reconstructed image is similar to the color of the real object, which is called true color. A.2.2 Dot matrix hologram
A.2.2. 1 Radiation-contraction effect
When the viewing direction is changed, the hologram shows dynamic changes of radiation-contraction. A.2,2. 2 Rotation effect
When the viewing direction is changed, the hologram shows dynamic changes of plane rotation (such as fan shape). A.2.2.3 Two-dimensional super line holography
The fine super line pattern in the image plane presents a multi-color rainbow. A.2.2.4 Flowing effect
When the sample is moved or rotated, its holographic pattern has a flowing visual change. A.2.3 Volume reflection holography
A.2.3.1 Monochrome volume holography
GB/T 17000—2009
The volume reflection holography recorded with a single wavelength, the whole image is one color, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.3.2 True color volume reflection holography
The volume reflection holography recorded with multiple wavelengths, the holographic image is multiple colors, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.4 Optical lens effect
A.2.4.1 Concave and convex lenses
The holographic image presents a concave lens or convex lens effect. A.2.4.2 Clear code marking
Through the lens, you can see the deep text. 2.2.5 Isotopic anomalies
When the sample is rotated, different images and texts are successively seen at the same position. 9
Hepin Partner Network ht1 Marking
The following markings shall be on the outer packaging or product certificate when the product leaves the factory: a) Product name and number.
b) Product specifications, quantity, batch number.
Name and address of the manufacturer.
d) Production date
e) Standard number and name based on which the product is produced.
Production license number.
g) Contents required by national laws, regulations and relevant policies. 8.2 Packaging
According to the provisions of 8.2 of GB/T 19425--2003. 8.3 Transportation
During transportation, the product shall be protected from sunlight and moisture, shall not be heavily pressed, and shall not be shipped together with chemicals and polluted products. It is not allowed to lower the product from a high place during transportation, and it shall be strictly prevented from collision and scratches by vehicles.
8.4 Storage
The product shall be stored in a warehouse that is windproof, moistureproof and fireproof. The air temperature and relative humidity in the warehouse should meet the storage requirements of holographic anti-counterfeiting products, and the storage period should ensure that the quality of holographic anti-counterfeiting products is not affected. 8.5 Safety measures
During the production, transportation, storage and other processes of holographic anti-counterfeiting products, enterprises should formulate safety and confidentiality measures and effectively implement 9 Environmental protection and hygiene
The production and sales of holographic anti-counterfeiting products should comply with the requirements of relevant national environmental protection and hygiene standards. 8
A. 1 Verification conditions
A.1.1 Light source
White light point light source.
A.1.2 Light source incident direction
Appendix A
(Normative Appendix)
Explicit holographic anti-counterfeiting identification features and verification methods Point light source is tilted from above the sample and observed in the normal direction. A.2 Anti-counterfeiting identification features of holograms
A.2.1 Rainbow remnant
A.2.1. 1 Multicolor (image plane) rainbow hologram
Different positions of the hologram in the image plane show different colors. A,2. 1. 2 Multicolor two-dimensional/three-dimensional images
Images with different depths of field show different colors. A.2. 1. 3 Three-dimensional hologram
Holograms are three-dimensional stereoscopic images.
A.2.1.4 True color
The two- or three-dimensional reconstructed image is similar to the color of the real object, which is called true color. A.2.2 Dot matrix hologram
A.2.2. 1 Radiation-contraction effect
When the viewing direction is changed, the hologram shows dynamic changes of radiation-contraction. A.2,2. 2 Rotation effect
When the viewing direction is changed, the hologram shows dynamic changes of plane rotation (such as fan shape). A.2.2.3 Two-dimensional super line holography
The fine super line pattern in the image plane presents a multi-color rainbow. A.2.2.4 Flowing effect
When the sample is moved or rotated, its holographic pattern has a flowing visual change. A.2.3 Volume reflection holography
A.2.3.1 Monochrome volume holography
GB/T 17000—2009
The volume reflection holography recorded with a single wavelength, the whole image is one color, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.3.2 True color volume reflection holography
The volume reflection holography recorded with multiple wavelengths, the holographic image is multiple colors, and it can have a three-dimensional effect when observed in the vertical and horizontal directions. A.2.4 Optical lens effect
A.2.4.1 Concave and convex lenses
The holographic image presents a concave lens or convex lens effect. A.2.4.2 Clear code marking
Through the lens, you can see the deep text. 2.2.5 Isotopic anomalies
When the sample is rotated, different images and texts are successively seen at the same position. 9
Hepin Partner Network ht
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.