This standard specifies the dimensions, technical requirements, inspection rules, packaging, storage and transportation of MT and MF arm-to-arm thyristor modules. This standard applies to arm-to-arm thyristor modules composed of ordinary thyristors and mixed arm-to-arm modules composed of ordinary thyristors and ordinary rectifiers. JB/T 7826.1-1995 MT, MF series arm-to-arm thyristor modules JB/T7826.1-1995 Standard download decompression password: www.bzxz.net

JB/T7826.1-1995
This standard is formulated to adapt to the research, development and application of thyristor modules and actively adopt international standards. The technical requirements and parameter indicators of this standard adopt the general level of similar products of foreign companies, and leave appropriate margins for enterprise standards. The basic standards used in this standard are the standards cited in Chapter 2 of this standard, and the latter are converted into my country's standards based on the principle of technical equivalence or reference to the IECTC47 basic standards.
The setting of the inspection items of this standard is based on the performance requirements of thyristor modules, and refers to the national standard CB4940 "Ordinary Thyristors", and some additions and deletions have been made.
The test methods adopted in this standard, except for the test methods specified in the industry standard JB/T7625.2 "Thyristor module test methods, arm pairs and anti-parallel arm pairs", are implemented in accordance with GB4024. In order to ensure the product quality of thyristor modules, this standard stipulates that at least one batch of inspections shall be carried out every six months according to the serial numbers 1 to 3 in the periodic inspection table 7.
Appendix A and Appendix B of this standard are both standard appendices. This standard is proposed and managed by Xi'an Electric Power Electronics Technology Research Institute. The drafting units of this standard are: Wuxi Radio Component Factory No. 5, Beijing Chunshu Rectifier Factory, Yangzhou Siling Electronics Co., Ltd., Xiafu Power Electronics Co., Ltd., Xiangfan Instrument Component Factory, and Fuxin Transistor Factory. The main drafters of this standard are: Dai Yongxiang, Huang Yaoxian, Que Weiguang, Huang Yifu, Sun Fumin, Zhang Zhaofu, and Gao Shanxing. 23
Mechanical Industry Standard of the People's Republic of China
MT, MF Series Arm-to-Thyristor Modules
JB/T7826.1-1995
This standard specifies the dimensions, technical requirements, inspection rules, packaging, storage and transportation of MT and MF arm-to-thyristor modules. This standard applies to arm-to-thyristor modules composed of ordinary thyristors and hybrid arm-to-thyristor modules composed of ordinary thyristors and ordinary rectifiers.
Reference standards
GB2423.4-81
GB4024-83
GB4937-85
GB4938-85
JB/T6306—92
JB/T7625.2-94
Product type
Model description
Ministry of Machinery Industry
Basic environmental test procedures for electrical and electronic products Test methods for reverse blocking triode thyristors of semiconductor devices Mechanical and climatic test methods for discrete semiconductor devices Semiconductor discrete devices Parts acceptance and reliability
Power semiconductor module dimensions
Thyristor module test method arm pair and anti-parallel arm pair M
-95-11-24 approved
VDRM (VRRM) level
On-state average current value (unit: A)
Electrical connection code
Thyristor (hybrid)
19960701 implementation
Electrical connection type
MTC type
MTK type
MFC (DT) type o-4
MFK type.
MFX type
Dimensions
JB/T7826.1-1995
Come! 。
Double-hole one-way radiator module shall comply with 3.3.2 of JB/T6306. 3.3.1
Four-hole one-way radiator module shall comply with 3.3.3 of JB/T6306. Rated values ​​and characteristic values
Parameter levels
MTA type.
MTX type
MFC (TD) type4
MFA type04
The levels of off-state repetitive peak voltage (VDRM) and reverse repetitive peak voltage (VRRM) shall comply with Table 1 (voltage and current are both single tube 4.1.1
core values, the same below).
The levels of critical rate of rise of on-state current (di/dt) shall comply with Table 2. Table 2
The levels of critical rate of rise of off-state voltage (dv/dt) shall comply with Table 3. Table 3
Rated values
Maximum rated values ​​(limit values)
shall comply with the provisions of Table 4,
and shall apply to the entire operating temperature range.
V/μus
JB/T7826.1-1995
Given by the manufacturer
Given by the manufacturer and maintenance factory
Given by the manufacturer and venting factory
Draft for review!
Characteristic values ​​shall comply with the requirements of Table 5
On-state average current
On-state peak voltage
Characteristic curve
Off-state load
Complex peak value
Reverse load
Complex peak value
JB/T7826.1-1995
≤150
≤150
≤150
≤200
≤200
≤250
≤250
≤300
Gate contact current
≤ 150
≤150
≤150
≤200
≤250
≤250
≤250
≤250
≤300
≤300
Gate contact voltage
At least the following characteristic curves of the module should be given in the enterprise standard or product manual: a)
Derating curve of module base plate temperature and on-state average current; on-state volt-ampere characteristic curve;
Gate non-transient thermal resistance and time curve (on-state average current ITcav) greater than 50A). Inspection rules
Batch inspection
Each batch of products must be inspected batch by batch according to Table 6. Table 6
Test items
Iox, IgkM
Test methods
Visual inspection (normal lighting and normal vision)
3.3 in JB/T 7625.2
3.1 and 3.2 in JB/T7625.2
3.4 ​​in GB 4024
3. 8
Sine wave 50Hz, voltage 2500V, holding time 1min
Qualification criteria
Marking is clear, the surface has no mechanical damage and contamination, in accordance with the provisions of Table 5
In accordance with the provisions of Table 5
In accordance with the provisions of Table 5
No breakdown, flashover phenomenon
Off-state voltage
Critical
Rise rate
Sampling plan
(Inspection level 1>AQL
Inspection items
JB/T7826.1-1995||tt| |Table 6 (end)
Test method
The dv/dt item is only implemented for the on-state average current Ittav> greater than 50A. Qualification criteria
Sampling plan
(Test level I)AQL
The specific sampling number of AQL is shown in Appendix A. If the remote batch inspection fails the initial submission, it can be resubmitted for re-inspection according to the method of tightening AQL by one level, but it can only be resubmitted once.
For the inspection of serial number 1, test samples with poor electrical characteristics can be used. Periodic inspection
Standardized products in normal production shall be subject to at least one batch of periodic inspections each year according to Table 7. Marked with (D) is a destructive test. Table 7
Test Items
Temperature Change Followed
Alternating Humidity (D)
Electrical Durability
(AC Blockage)
According to the Appearance Drawing
Test Method
GB4937 3.1.1, Two Box Method, Ta40+C, T, =125-1C, 5 Cycles, 0.5h Each Exposure, GB2423.4, Severe Level; Temperature 55C, 6 Days of Cycles CB4938 2.3.2, 168h, TC, Sine Wave 50Hz, 70%VM, 70 %VDX
3.6 of GB4024, 25℃, Vp=12V, gate circuit without Rs, impulse current 0.1ITA)
3.7 of GB4024, 25℃, V,=12V, gate circuit without R, trigger current pulse te≤0.5μs, twc=100pS, 50Hz, 10V, 60 or 80
4.2 of GB4024, T-iC, 20 times, one cycleJB/T7625.24.1
3.8 of GB4024, T, gate open circuit
3.5, T, load resistance meets the current limiting current greater than I, less than Irsx
GB4024 4.7, T
GB4024 4:5, T, gate pulse bottom width 400μ8GB4024 4.6, T,
ly=3~5lat, tr1.5μs,
GB4024 4.4, T,
pulse width 20us,
qualification criteria
meet the requirements of the drawing
measurement after test:
V≤1.1USL
IRRX≤2US L
IoRy2USL
Vso meets the requirements of Table 4
Measurement after test:
Same as serial number 2
Meet the requirements of Table 5
Measurement after test,
Same as serial number 2
Meet the requirements of Table 5
Meet the requirements of Table 5
Meet the requirements of Table 4
Meet the requirements of Table 4
Meet the requirements of Table 4www.bzxz.net
Measurement after test:
Same as serial number 2
Sampling plan||tt ||Inspection items
Electrical durability
(AC blocking)
High temperature storage
Shock (D) or vibration
16 Release batch confirmation record
JB/T7826.1-1995
Table 7 (end)
Inspection method
2.3.2 of GB4938, 1000h, other network numbers 333.2 of GB1937, T-1C, 1000=h
2.3 of CB4937, 196m/s*, 100~2000Ha, three mutually vertical Vertical direction, scan for 2h in each direction, for a total of 6h; GB4937 2.4, 980m/s*, continuous 6m5, half-sine waveform, three impacts in two directions of three mutually perpendicular axes for 3 times, for a total of 18 times. Qualified judgment criteria
Measurement after test,
Same as No. 2
Measurement after test:
Same as No. 2
Measurement after test:
Same as No. 2
Sampling plan
Briefly give the relevant attribute data values ​​of each item and the relevant parameters before and after the test and the acid test conclusion. The numbers in square brackets are the number of samples greater than 50A. 2USL is the upper limit of the specification corresponding to Table 5.
3If No. 13, 1000h test is continued according to No. 3 test, the sample of No. 13 must be randomly determined by No. 3 with the funeral objects before No. 3 test.
Remote batch inspection serial number 1~5 and periodic inspection serial number 4~12. The samples after the test can be used for other test items. 4
If the first sampling inspection of the periodic inspection fails, it can be inspected again by additional sampling according to Appendix B. 5.3 Quality category
The product quality assessment category of this standard is Class 1. 6
Marking and packaging
Marking on the module
Product model;
Manufacturer name or trademark;
Electrical connection diagram and terminal identification;
Product batch number or serial number.
Marking on the packaging box
Product model and quality category;
Manufacturer name and trademark;
Inspection batch identification code;
Number of this standard;
Moisture-proof and rain-proof marking.
6.3 Packaging
Product packaging must ensure that the product is not mechanically damaged during transportation; the manufacturer's name, consignee's name, and product name should be printed on the packaging; and there should be a product certificate in the packaging box.
Performance search can be supplemented once,
Appendix A (Standard Appendix)
Batch range
91~150
151~280
281~500
501~1200
1201~3200
320110000
10001~35000
35001150000
This table belongs to the inspection level (IL) 1
c is the qualified judgment number, r is the unqualified judgment number 2
AQL sampling table
AQL(%)
The arrow indicates that the first down sampling plan should be used. If the sample pointed to by the arrow is equal to or greater than the batch, the batch should be inspected 100%.
Appendix B (Standard Appendix)
Additional Sampling Table
Initial Sampling
Additional Sampling
Additional Number
Number of Qualified Judgements3 Packaging
Product packaging must ensure that the product is not mechanically damaged during transportation; the manufacturer's name, consignee's name, and product name should be printed on the packaging; there should be a product certificate in the packaging box.
Performance search can be supplemented once,
Appendix A (Standard Appendix)
Batch range
91~150
151~280
281~500
501~1200
1201~3200
320110000
10001~35000
35001150000
This table belongs to the inspection level (IL) 1
c is the qualified judgment number, r is the unqualified judgment number 2
AQL sampling table
AQL(%)
The arrow indicates that the first down sampling plan should be used. If the sample pointed to by the arrow is equal to or greater than the batch, the batch should be inspected 100%.
Appendix B (Standard Appendix)
Additional Sampling Table
Initial Sampling
Additional Sampling
Additional Number
Number of Qualified Judgements3 Packaging
Product packaging must ensure that the product is not mechanically damaged during transportation; the manufacturer's name, consignee's name, and product name should be printed on the packaging; there should be a product certificate in the packaging box.
Performance search can be supplemented once,
Appendix A (Standard Appendix)
Batch range
91~150
151~280
281~500
501~1200
1201~3200
320110000
10001~35000
35001150000
This table belongs to the inspection level (IL) 1
c is the qualified judgment number, r is the unqualified judgment number 2
AQL sampling table
AQL(%)
The arrow indicates that the first down sampling plan should be used. If the sample pointed to by the arrow is equal to or greater than the batch, the batch should be inspected 100%.
Appendix B (Standard Appendix)
Additional Sampling Table
Initial Sampling
Additional Sampling
Additional Number
Number of Qualified Judgements
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.