title>HG/T 3131-1998 Paddle Dryer - HG/T 3131-1998 - Chinese standardNet - bzxz.net
Home > HG > HG/T 3131-1998 Paddle Dryer
HG/T 3131-1998 Paddle Dryer

Basic Information

Standard ID: HG/T 3131-1998

Standard Name: Paddle Dryer

Chinese Name: 桨叶干燥机

Standard category:Chemical industry standards (HG)

state:in force

Date of Release1998-03-23

Date of Implementation:1998-05-01

standard classification number

Standard ICS number:Chemical Technology>>71.120 Chemical Equipment Petroleum and Related Technology>>Oil and Gas Industry Equipment>>75.180.20 Processing Equipment

Standard Classification Number:Chemical Industry>>Chemical Machinery and Equipment>>G92 Chemical Machinery

associated standards

Publication information

Publication date:1998-05-01

other information

drafter:Hao Jianlin, Xie Zhen, Yuan Fuxing, etc.

Drafting unit:Sanmenxia Chemical Machinery Plant, Chemical Machinery Research Institute of the Ministry of Chemical Industry

Focal point unit:Chemical Machinery and Equipment Standardization Technical Committee of the Ministry of Chemical Industry

Proposing unit:China National Chemical Equipment Corporation

Publishing department:Ministry of Chemical Industry of the People's Republic of China

Introduction to standards:

This standard specifies the classification and naming, basic parameters, requirements, test methods, inspection rules and marking, packaging, storage and transportation of paddle dryers (hereinafter referred to as dryers). This standard is applicable to drying various pastes, powders, granules and other heat-sensitive materials. HG/T 3131-1998 Paddle Dryer HG/T3131-1998 Standard download decompression password: www.bzxz.net

Some standard content:

Ics 71. 120; 75. 180.20
Registration No. 1398—1998
Chemical Industry Standard of the People's Republic of China
HIG/T3131-1998
Paddle dryer
1998—03—23 Issued
Ministry of Chemical Industry of the People's Republic of China
1999—01—01 Implementation
WuGB/T3131—1998
This standard is formulated based on the start-up of domestic paddle dryers, the establishment of verification test equipment for dryers, the subsequent research on drying mechanism and the successful development of a series of products. The series specified in this standard have jacket volumes less than 450L. However, from the perspective of strength design, the paddle shaft and jacket components are subject to multiple loads. Therefore, in the requirements for material selection, inspection and testing, some clauses directly quote the provisions of GB150, while others directly put forward specific requirements.
This standard is proposed by China National Chemical Equipment Corporation. This standard is under the jurisdiction of the Chemical Machinery and Equipment Standardization Technical Committee of the Ministry of Chemical Industry. The drafting units of this standard are: Sanmenxia Chemical Machinery Factory, Chemical Machinery Research Institute of the Ministry of Chemical Industry. The main drafters of this standard are: Hao Jianlin, Xie Zhen, Yuan Fuxing, Sun Zhongxin, Xu Jianzhuang, Wang Yi. 1 Scope
Chemical Industry Standard of the People's Republic of China
Paddle dryer
Paddledryer
HG/T3131—1998
This standard specifies the classification and naming, basic parameters, requirements, test methods, inspection rules and markings, packaging, storage and transportation of paddle dryers (hereinafter referred to as dryers).
This standard applies to single-axis, double-axis and four-axis paddle dryers for drying various sticky, powdery, granular and other heat-sensitive organic and inorganic materials and heat-sensitive materials under vacuum conditions. 2 Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB150—1998
GB985--88
GB1801-79
GB327488
GB 3797--89
GB/T4237—94
GB4879—85
GB6654—1996
GB8163—87
GB/T13306—91
GB/T13384—92
GB/T14976—94
JB4730—94
JB4733-1996
3 Classification and namingbzxz.net
3.1 Type
Basic forms and dimensional tolerances of weld grooves for gas welding, manual arc welding and gas shielded welding With matching dimensions up to 500mm, tolerance bands and matching of holes and shafts Carbon structural steel and low alloy structural steel hot-rolled thick steel plates and steel strips Electric control equipment Part II Electric control equipment equipped with electronic devices Stainless steel hot-rolled steel plates
Rust-proof packaging
Explanation
Carbon steel and low alloy steel thick steel plates for pressure vessels Seamless steel pipes for conveying fluids
General technical conditions for packaging of electromechanical products
Stainless steel seamless steel pipes for conveying fluids Large width greasy 0 Nondestructive testing of pressure vessels
Explosive stainless steel composite steel plates for pressure vessels 3.1.1 The blade dryer is mainly composed of a rotating hollow blade shaft, a jacketed fuselage and a drive device, and is installed horizontally and tilted. 2.1.2 The heating medium can be saturated steam, hot water or heat transfer oil. 3.1.3 The dryer is heated and stirred by a heating medium such as high-temperature steam or hot water passing through the hollow shaft and hollow blades. Approved by the Ministry of Chemical Industry of the People's Republic of China on March 23, 1998 and implemented on January 1, 1999
W.3.2 Model
3.2.1 Model indication method
The code for the number of impeller shafts shall be as specified in Table 1,
3. 2. 1. 1
HG/T3131-1998
Heating medium type code
Heat transfer area, m*
Beam dryer code, JG
Code for the number of impeller shafts
Table 1 Code for the number of impeller shafts
Base of the number of impeller shafts
3.2.1.2 The code for the type of heating medium shall be as specified in Table 2. 2 Heating medium type code
Heating medium type
Saturated steam
Hot water, thermal oil
3.2.2 Model example
The number of paddle shafts is 2, the heat transfer area is 25m, and the heating medium is saturated steam. Paddle dryer, JG-25Q
The number of paddle shafts is 4, the heat transfer area is 100m\, and the heating medium is hot water or thermal oil. Dyeing leaf dryer, SJG-100Y
3.3 Basic parameters
The basic parameters of the dryer shall comply with the provisions of Table 3, Table 4 and Table 5. 4.1 Design
4.1.1, Machine performance
4.1.1.1 The design parameters of the dryer shall comply with the provisions of Table 8, Table 4 and Table 5. 4.1.1.2 The structure of the dryer is shown in Figure 1. 4.1.1.3 During load operation, the noise level of the dryer shall not exceed 75dB (A) 4.1.1.4 The bearing temperature rise of the main motor of the dryer shall not exceed 40℃. 4.1.1.5 Before the dryer is overhauled, the average friction-free working time shall not be less than 7500h. 2
11G/T3131-1998
I-ora
All kinds of standard materials
Heat transfer area
Effective volume
Motor power
Shaft and jacket design pressure MPa
HG/T3131—1998
Table 5 Basic parameters of four-shaft paddle dryer
SJG-15.7SJG-23.5SJG-32.7
Drive device
Feed
Rotary joint
4.1.2 Parts
7-5×2
Bracket Poly-axle
Dual-axle award blade
42.5SJG-61.3SJG-
Discharge port
Dryer structure
4.1.2.1 The design pressure of the jacket and paddle shaft shall not be lower than the maximum working pressure of the heating medium, which is generally taken as 0.6MPa. 4.1.2.2 In addition to considering the maximum working pressure of the heating medium, the strength design of the jacket and paddle shaft should also consider the combined effect of the stirring material load and the corrosion and wear of the material on the paddle shaft
4.1.2.3 The top cover and end plate and other parts of the shell side are designed according to the pressure. When there are special drying requirements (such as vacuum drying or too high carrier gas pressure, or the evaporated wet gas is absolutely not allowed to leak), special design treatment is required. 4.1.2.4 Whether the surface of the material in contact with the material is polished or not shall be determined according to the actual needs of the material to be dried and the provisions of the order contract between the supply and demand parties.
4.2 Materials
4.2.1 The materials of the main parts of the dryer shall comply with the following provisions and shall have corresponding material inspection certificates and quality certificates. 4.2.1.1 The materials of the parts in contact with the material such as the fuselage and the top cover shall be selected from the national standards or industry standards of the materials according to the degree of corrosion of the dried material.
4.2.1.2 When the hollow shaft of the slurry is made of steel pipe as raw material, the material shall comply with the provisions of GB8163 or GB/T14976; when steel plate is used for coil welding, the plate used shall comply with the provisions of GB6654, GB3274GB/T4237, and JB4733. 4.2.1.3 The materials of the blades, fuselage and jacket shall comply with the provisions of GB6654.GB3274 or GB/T4237. 4.2.2 All supporting purchased parts shall meet the requirements of the corresponding product standards and shall have product certificates. 4.3 Manufacturing
wuHG/13131—1998
4.3.1 In addition to meeting the requirements of this standard, the manufacturing of the dryer shall also meet the requirements of the product drawings and technical documents approved through the prescribed procedures.
4.3.2 Steel plate punching and shearing parts shall not have defects such as cracks, interlayers, depressions, wrinkles, etc., and sharp points and burrs shall be removed. 4.3.3 The welding process regulations for jackets and slurry transfers shall be formulated in accordance with the requirements of the drawings and the qualified welding processes. Welders must be certified to work. 4.3.4 The weld groove of manual welding of welded parts shall meet the requirements of GB985. When there is no provision in the drawings, the height of the weld leg of the fillet weld shall be the thickness of the thinner of the two welded parts.
4.3.5 The welds of jackets, hollow shafts, blades and other welded parts shall not have cracks, arc pits and other defects. 4.3.6 The butt welds of the jacket and the longitudinal and circumferential welds of the rolled hollow shaft shall be subjected to radiographic inspection in accordance with the provisions of JB4730. The inspection length shall not be less than 20% of the length of each weld. The cylinder grade is qualified. The welds of the blade and the blade, the hollow shaft, and the hollow shaft and the end shaft shall be subjected to magnetic particle or penetrant inspection in accordance with the provisions of JB4730. Grade I is qualified. 4.3.7 The machining dimensional accuracy of the main parts shall comply with the provisions of GB 1801. 4.3.8 The contour tolerance of the curved fuselage shall not exceed 4mm. 4.3.9 After the hollow shaft and blade, the coaxiality tolerance of the two ends of the hollow shaft and end shaft shall not exceed 0.04mm. 4.3.10 When the length of the propeller shaft is not more than 2m, its straightness tolerance shall not exceed 0.12mm. When the length of the propeller shaft is more than 2m, its straightness tolerance shall not exceed 0.25mm.
4.3.11 The jacket and propeller shaft shall be subjected to water pressure test. The test method shall comply with the provisions of 3.8 of GB150-1998, and the test pressure shall comply with the provisions of 3.8 of GB150-1998. When the above parts made of stainless steel are subjected to water pressure test, when the permanent collapse cannot be completely removed, the hydrogen ion content in the water shall be controlled to be less than 25ppm. 4.4 Assembly
4.4.1 All parts can be assembled only after they have passed the inspection. 4.4.2 When the slurry shaft is rotating, it should rotate freely without friction or biting. 4.4.3 The rotation direction of the slurry shaft should be consistent with the requirements of the product general drawing. 4.4.4 The transmission parts of the dryer should rotate smoothly without abnormal sounds. 4.4.5 The insulation resistance value between the conductive part of the electrical system and the dryer body should be greater than 2MO, and the resistance value between the grounding terminal and the fan housing of the electrical equipment and the dryer body should not be greater than 0.12. 4.1. 6 The electrical system should be equipped with a protective grounding terminal with obvious markings. 4.4.7 The live parts of the electrical system should not be exposed, and the screws fixing the conductive parts should have anti-loosening measures. 4.5 Anti-rust and painting
The anti-rust and painting of the outer surface of the dryer should comply with the requirements of the drawings, and the paint film should be uniform, flat, smooth and firm, without obvious tears, and the surface should be free of cracks, wrinkles, bubbles, scars and adhesion particles. 5 Test method
5.1 No-load test
Before the dryer leaves the factory and after the user installs it, a no-load test should be carried out. The test time should not be less than 2h, the number of starts and stops should not be less than 5 times, and it should meet the following requirements:
a) The action of the motor and control electrical appliances should be interlocked, sensitive and accurate: b) The lubrication of each lubrication point should be positive, without leakage or seepage! c) The main engine should run smoothly without abnormal glass sound d) The running direction of the pulp shaft should comply with the provisions of 4. 4.3, and its speed adjustment should be flexible and free 1. ) The connection of each fastener should be reliable and not loose. 5.2 Load test
5.2.1 Load test is carried out at the site of use
5. 2.2 The conditions, methods and requirements of the test shall comply with the provisions of 3. 3, 4.1.1. 3.4. 1. 1. 4, HG/T3131-1998
5.2.3 The noise test of the dryer shall be carried out at a distance of 1m from the machine. 5.2.4 The insulation dielectric strength of the electrical system shall comply with the provisions of GB3797. 6 Inspection rules
6.1 The dryer shall be inspected by the inspection department of the manufacturer and a certificate of conformity shall be issued. 6.2 The inspection of the dryer is divided into factory inspection and type inspection. 6.2.1 Factory inspection
The items and requirements of the factory inspection shall comply with the provisions of 4.3, 4.4, 4.5 and 5.1. 6.2.2 Type inspection
6.2.2.1 The items and requirements of type inspection shall be in accordance with the provisions of 3.3, 4:11.3411.4.4.8.4.4, 4.5, 5.1. 6.2.2.2 Type inspection shall be carried out by randomly selecting at least one unit from the qualified products of factory inspection. 6.2.3 Type inspection shall be carried out in any of the following cases: a) During product trial production, finalization and appraisal: Dian Ke He Dian Mei Neng # San Neng Institute b) When there are major changes in design, materials and processes: c) When production is stopped for twelve months and resumed
d) When the normal production time reaches twenty-four months, e) When there is a major difference between the factory inspection result and the last type inspection result: f) When the national quality supervision agency puts forward type inspection requirements. 6.3 Inspection rules and judgment
6.3.1 Each dryer shall be inspected according to 6.2.1. If any of the inspection data does not meet the requirements, the dryer shall be judged as unqualified for factory inspection.
6.3.2 If the type inspection meets the requirements of 6.2.2, the type inspection shall be judged as qualified. If any item does not meet the requirements, the type inspection shall be judged as unqualified.
Marking, packaging, storage and transportation
M生大#医中来餐防饰林
7.1 The dryer should have a product label in a conspicuous position. The label should comply with the provisions of GB/13306 and include the following: a) Product name and model; b) Motor rated power (kW) speed (r/min); c) Heat transfer area (m); d) Design pressure (MPa); e) Net weight; d) Production date, product number: g) Manufacturer's name.
7.2 Packaging
7.2.1 For parts with anti-rust requirements, anti-rust treatment should be carried out according to the provisions of GB4879 before packaging. 7.2.2 The material inlet and outlet of the dryer should be blocked, and the blocking parts should be resistant to wind and rain erosion and withstand accidental damage. 7.2.3 The documents provided with the product should be placed in a waterproof bag and then in the packaging box. The packaging should comply with the provisions of GB/T13384. 7.2.4 The outer wall of the packaging box should indicate the following: a) Receiving unit, detailed address:
b) Product name, model, factory number: c) Overall dimensions, gross weight;
d) Shipping unit, detailed address.
7.2.5 The documents provided with the product should include the following information: 6
a) Packing list
b) Product certificate and quality certificate!
c) Product instruction manual:
d) Installation drawing.
7.2.S The quality certificate should include the following: in) Technical parameters;
b) Material of main components
c) Hydrostatic test and non-destructive testing results.
HG/ T3131-1998
7.3 Transportation
7.3.1 The dryer should be stored in a clean, dry, ventilated warehouse without corrosive media; protective measures should be taken when stored outdoors. 7.3.2 During the transportation of the dryer, measures should be taken to prevent the product or packaging box from being damaged by vibration or collision. People's Republic of China
Chemical Industry Standard
Pulp Dryer
HG/T3131—1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing Plant
All rights reserved. Reproduction is prohibited
Format 880×12301/16 Printing Sheet 0.75 Words 15,000 Words First Edition September 1998 First Printing September 1998 Printing Quantity 1-1005 The insulation resistance between the conductive part of the electrical system and the dryer body should be greater than 2MO, and the resistance between the grounding terminal and the electrical equipment fan housing and the dryer body should not be greater than 0.12. 4.1. 6 The electrical system should be equipped with a protective grounding terminal with obvious markings. 4.4.7 The live parts of the electrical system should not be exposed, and the screws fixing the conductive parts should have anti-loosening measures. 4.5 Anti-rust and painting
The anti-rust and painting of the outer surface of the dryer should comply with the requirements of the drawings, and the paint film should be uniform, flat, smooth and firm, without obvious tears, and the surface should be free of cracks, wrinkles, bubbles, scars and adhesion particles. 5 Test method
5.1 No-load test
Before the dryer leaves the factory and after the user installs it, a no-load test should be carried out. The test time should not be less than 2h, the number of starts and stops should not be less than 5 times, and it should meet the following requirements:
a) The action of the motor and control electrical appliances should be interlocked, sensitive and accurate: b) The lubrication of each lubrication point should be positive, without leakage or seepage! c) The main engine should run smoothly without abnormal glass sound d) The running direction of the pulp shaft should comply with the provisions of 4. 4.3, and its speed adjustment should be flexible and free 1. ) The connection of each fastener should be reliable and not loose. 5.2 Load test
5.2.1 Load test is carried out at the site of use
5. 2.2 The conditions, methods and requirements of the test shall comply with the provisions of 3. 3, 4.1.1. 3.4. 1. 1. 4, HG/T3131-1998
5.2.3 The noise test of the dryer shall be carried out at a distance of 1m from the machine. 5.2.4 The insulation dielectric strength of the electrical system shall comply with the provisions of GB3797. 6 Inspection rules
6.1 The dryer shall be inspected by the inspection department of the manufacturer and a certificate of conformity shall be issued. 6.2 The inspection of the dryer is divided into factory inspection and type inspection. 6.2.1 Factory inspection
The items and requirements of the factory inspection shall comply with the provisions of 4.3, 4.4, 4.5 and 5.1. 6.2.2 Type inspection
6.2.2.1 The items and requirements of type inspection shall be in accordance with the provisions of 3.3, 4:11.3411.4.4.8.4.4, 4.5, 5.1. 6.2.2.2 Type inspection shall be carried out by randomly selecting at least one unit from the qualified products of factory inspection. 6.2.3 Type inspection shall be carried out in any of the following cases: a) During product trial production, finalization and appraisal: Dian Ke He Dian Mei Neng # San Neng Institute b) When there are major changes in design, materials and processes: c) When production is stopped for twelve months and resumed
d) When the normal production time reaches twenty-four months, e) When there is a major difference between the factory inspection result and the last type inspection result: f) When the national quality supervision agency puts forward type inspection requirements. 6.3 Inspection rules and judgment
6.3.1 Each dryer shall be inspected according to 6.2.1. If any of the inspection data does not meet the requirements, the dryer shall be judged as unqualified for factory inspection.
6.3.2 If the type inspection meets the requirements of 6.2.2, the type inspection shall be judged as qualified. If any item does not meet the requirements, the type inspection shall be judged as unqualified.
Marking, packaging, storage and transportation
M生大#医中来餐防饰林
7.1 The dryer should have a product label in a conspicuous position. The label should comply with the provisions of GB/13306 and include the following: a) Product name and model; b) Motor rated power (kW) speed (r/min); c) Heat transfer area (m); d) Design pressure (MPa); e) Net weight; d) Production date, product number: g) Manufacturer's name.
7.2 Packaging
7.2.1 For parts with anti-rust requirements, anti-rust treatment should be carried out according to the provisions of GB4879 before packaging. 7.2.2 The material inlet and outlet of the dryer should be blocked, and the blocking parts should be resistant to wind and rain erosion and withstand accidental damage. 7.2.3 The documents provided with the product should be placed in a waterproof bag and then in the packaging box. The packaging should comply with the provisions of GB/T13384. 7.2.4 The outer wall of the packaging box should indicate the following: a) Receiving unit, detailed address:
b) Product name, model, factory number: c) Overall dimensions, gross weight;
d) Shipping unit, detailed address.
7.2.5 The documents provided with the product should include the following information: 6
a) Packing list
b) Product certificate and quality certificate!
c) Product instruction manual:
d) Installation drawing.
7.2.S The quality certificate should include the following: in) Technical parameters;
b) Material of main components
c) Hydrostatic test and non-destructive testing results.
HG/ T3131-1998
7.3 Transportation
7.3.1 The dryer should be stored in a clean, dry, ventilated warehouse without corrosive media; protective measures should be taken when stored outdoors. 7.3.2 During the transportation of the dryer, measures should be taken to prevent the product or packaging box from being damaged by vibration or collision. People's Republic of China
Chemical Industry Standard
Pulp Dryer
HG/T3131—1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing Plant
All rights reserved. Reproduction is prohibited
Format 880×12301/16 Printing Sheet 0.75 Words 15,000 Words First Edition September 1998 First Printing September 1998 Printing Quantity 1-1005 The insulation resistance between the conductive part of the electrical system and the dryer body should be greater than 2MO, and the resistance between the grounding terminal and the electrical equipment fan housing and the dryer body should not be greater than 0.12. 4.1. 6 The electrical system should be equipped with a protective grounding terminal with obvious markings. 4.4.7 The live parts of the electrical system should not be exposed, and the screws fixing the conductive parts should have anti-loosening measures. 4.5 Anti-rust and painting
The anti-rust and painting of the outer surface of the dryer should comply with the requirements of the drawings, and the paint film should be uniform, flat, smooth and firm, without obvious tears, and the surface should be free of cracks, wrinkles, bubbles, scars and adhesion particles. 5 Test method
5.1 No-load test
Before the dryer leaves the factory and after the user installs it, a no-load test should be carried out. The test time should not be less than 2h, the number of starts and stops should not be less than 5 times, and it should meet the following requirements:
a) The action of the motor and control electrical appliances should be interlocked, sensitive and accurate: b) The lubrication of each lubrication point should be positive, without leakage or seepage! c) The main engine should run smoothly without abnormal glass sound d) The running direction of the pulp shaft should comply with the provisions of 4. 4.3, and its speed adjustment should be flexible and free 1. ) The connection of each fastener should be reliable and not loose. 5.2 Load test
5.2.1 Load test is carried out at the site of use
5. 2.2 The conditions, methods and requirements of the test shall comply with the provisions of 3. 3, 4.1.1. 3.4. 1. 1. 4, HG/T3131-1998
5.2.3 The noise test of the dryer shall be carried out at a distance of 1m from the machine. 5.2.4 The insulation dielectric strength of the electrical system shall comply with the provisions of GB3797. 6 Inspection rules
6.1 The dryer shall be inspected by the inspection department of the manufacturer and a certificate of conformity shall be issued. 6.2 The inspection of the dryer is divided into factory inspection and type inspection. 6.2.1 Factory inspection
The items and requirements of the factory inspection shall comply with the provisions of 4.3, 4.4, 4.5 and 5.1. 6.2.2 Type inspection
6.2.2.1 The items and requirements of type inspection shall be in accordance with the provisions of 3.3, 4:11.3411.4.4.8.4.4, 4.5, 5.1. 6.2.2.2 Type inspection shall be carried out by randomly selecting at least one unit from the qualified products of factory inspection. 6.2.3 Type inspection shall be carried out in any of the following cases: a) During product trial production, finalization and appraisal: Dian Ke He Dian Mei Neng # San Neng Institute b) When there are major changes in design, materials and processes: c) When production is stopped for twelve months and resumed
d) When the normal production time reaches twenty-four months, e) When there is a major difference between the factory inspection result and the last type inspection result: f) When the national quality supervision agency puts forward type inspection requirements. 6.3 Inspection rules and judgment
6.3.1 Each dryer shall be inspected according to 6.2.1. If any of the inspection data does not meet the requirements, the dryer shall be judged as unqualified for factory inspection.
6.3.2 If the type inspection meets the requirements of 6.2.2, the type inspection shall be judged as qualified. If any item does not meet the requirements, the type inspection shall be judged as unqualified.
Marking, packaging, storage and transportation
M生大#医中来餐防饰林
7.1 The dryer should have a product label in a conspicuous position. The label should comply with the provisions of GB/13306 and include the following: a) Product name and model; b) Motor rated power (kW) speed (r/min); c) Heat transfer area (m); d) Design pressure (MPa); e) Net weight; d) Production date, product number: g) Manufacturer's name.
7.2 Packaging
7.2.1 For parts with anti-rust requirements, anti-rust treatment should be carried out according to the provisions of GB4879 before packaging. 7.2.2 The material inlet and outlet of the dryer should be blocked, and the blocking parts should be resistant to wind and rain erosion and withstand accidental damage. 7.2.3 The documents provided with the product should be placed in a waterproof bag and then in the packaging box. The packaging should comply with the provisions of GB/T13384. 7.2.4 The outer wall of the packaging box should indicate the following: a) Receiving unit, detailed address:
b) Product name, model, factory number: c) Overall dimensions, gross weight;
d) Shipping unit, detailed address.
7.2.5 The documents provided with the product should include the following information: 6
a) Packing list
b) Product certificate and quality certificate!
c) Product instruction manual:
d) Installation drawing.
7.2.S The quality certificate should include the following: in) Technical parameters;
b) Material of main components
c) Hydrostatic test and non-destructive testing results.
HG/ T3131-1998
7.3 Transportation
7.3.1 The dryer should be stored in a clean, dry, ventilated warehouse without corrosive media; protective measures should be taken when stored outdoors. 7.3.2 During the transportation of the dryer, measures should be taken to prevent the product or packaging box from being damaged by vibration or collision. People's Republic of China
Chemical Industry Standard
Pulp Dryer
HG/T3131—1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing Plant
All rights reserved. Reproduction is prohibited
Format 880×12301/16 Printing Sheet 0.75 Words 15,000 Words First Edition September 1998 First Printing September 1998 Printing Quantity 1-1001 The dryer should have a product label in a conspicuous position. The label should comply with the provisions of GB/13306 and include the following: a) Product name and model; b) Motor rated power (kW) speed (r/min); c) Heat transfer area (m); d) Design pressure (MPa); e) Net weight; d) Production date, product number; g) Manufacturer name. 7.2 Packaging 7.2.1 For parts with anti-rust requirements, anti-rust treatment should be carried out according to the provisions of GB4879 before packaging. 7.2.2 The material inlet and outlet of the dryer should be blocked, and the blocking parts should be resistant to wind and rain erosion and withstand accidental damage. 7.2.3 The documents provided with the machine should be placed in a waterproof bag and packed in the packaging box. The packaging should comply with the provisions of GB/T13384. 7.2.4 The outer wall of the packing box should be marked with the following: a) Receiving unit, detailed address:
b) Product name, model, factory number: c) Overall dimensions, gross weight;
d) Shipping unit, detailed address.
7.2.5 The random documents should include the following information: 6
a) Packing list
b) Product certificate and quality certificate!
c) Product instruction manual:
d) Installation drawing.
7.2.S The quality certificate should include the following content: in) Technical parameters;
b) Material of main components
c) Hydrostatic test and non-destructive testing results.
HG/ T3131-1998
7.3 Transportation
7.3.1 The dryer should be stored in a clean, dry, ventilated warehouse without corrosive media; protective measures should be taken when stored outdoors. 7.3.2 During the transportation of the dryer, measures should be taken to prevent the product or packaging box from being damaged by vibration or collision. People's Republic of China
Chemical Industry Standard
Pulp Dryer
HG/T3131—1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing Plant
All rights reserved. Reproduction is prohibited
Format 880×12301/16 Printing Sheet 0.75 Words 15,000 Words First Edition September 1998 First Printing September 1998 Printing Quantity 1-1001 The dryer should have a product label in a conspicuous position. The label should comply with the provisions of GB/13306 and include the following: a) Product name and model; b) Motor rated power (kW) speed (r/min); c) Heat transfer area (m) d) Design pressure (MPa); e) Net weight; production date, product number; g) Manufacturer name. 7.2 Packaging 7.2.1 For parts with anti-rust requirements, anti-rust treatment should be carried out according to the provisions of GB4879 before packaging. 7.2.2 The material inlet and outlet of the dryer should be blocked, and the blocking parts should be resistant to wind and rain erosion and withstand accidental damage. 7.2.3 The documents provided with the machine should be placed in a waterproof bag and packed in the packaging box. The packaging should comply with the provisions of GB/T13384. 7.2.4 The outer wall of the packing box should be marked with the following: a) Receiving unit, detailed address:
b) Product name, model, factory number: c) Overall dimensions, gross weight;
d) Shipping unit, detailed address.
7.2.5 The random documents should include the following information: 6
a) Packing list
b) Product certificate and quality certificate!
c) Product manual:
d) Installation drawing.
7.2.S The quality certificate should include the following content: in) Technical parameters;
b) Material of main components
c) Water pressure test and non-destructive testing results.
HG/ T3131-1998
7.3 Transportation
7.3.1 The dryer should be stored in a clean, dry, ventilated warehouse without corrosive media; protective measures should be taken when stored outdoors. 7.3.2 During the transportation of the dryer, measures should be taken to prevent the product or packaging box from being damaged by vibration or collision. People's Republic of China
Chemical Industry Standard
Pulp Dryer
HG/T3131—1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing Plant
All rights reserved. Reproduction is prohibited
Format 880×12301/16 Printing Sheet 0.75 Words 15,000 Words First Edition September 1998 First Printing September 1998 Printing Quantity 1-100
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.