JB/T 3411.104-1999 7:24 Dimensions of Morse taper intermediate sleeves for taper/forced transmission
Basic Information
Standard ID:
JB/T 3411.104-1999
Standard Name: 7:24 Dimensions of Morse taper intermediate sleeves for taper/forced transmission
Chinese Name:
7：24 圆锥/强制传动的莫氏圆锥中间套 尺寸
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1999-05-20
Date of Implementation:2000-01-01
standard classification number
Standard ICS number:Mechanical Manufacturing>>Machine Tools>>25.080.01 General Machine Tools
Standard Classification Number:Machinery>>Metal Cutting Machine Tools>>J52 Machine Tool Accessories and Accessories
associated standards
alternative situation:JB 3515-1983
Procurement status:neq ISO 5415:1977
Publication information
other information
Focal point unit:Mechanical Science Research Institute
Publishing department:Mechanical Science Research Institute
Introduction to standards:
JB/T 3411.104-1999 This standard is a revision of JB 3515-83 "7:24 cone/forced transmission Morse cone intermediate sleeve dimensions". Only the following points were modified during the revision, and the main technical content remained unchanged: - Writing format; - Standard name plus English; - Relevant reference standards and related contents; - Thread drawing method. This standard is not equivalent to ISO 5415:1997 "Transition sleeve with 7/24 outer cone, Morse inner cone and connecting screws". This standard specifies the type and size of 7:24 cone/forced transmission Morse cone intermediate sleeves. JB/T 3411.104-1999 7:24 cone/forced transmission Morse cone intermediate sleeve dimensions JB/T3411.104-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC5 25.00.01
Mechanical Industry Standard of the People's Republic of China
IB/T 3411.101-3411.127—1999 Accessories for milling machines
Accessories afmilling maclhincs1999-05-2U Issued by
National Machinery Industry Bureau
Implementation on 2000-01-01
Mechanical Industry Standard of the People's Republic of China
724 Taper/positive drive
Morse taper intermediate sleeve
Size: Inch
Changing dameter bush with 7 : 24taper/positivemosetaper-Diaensfops This standard specifies the type and size of 7:24 brushless brush drive intermediate sleeves. 2 Reference standards
JB/T3411.14—199g
Replacement JR1
The following standards contain provisions that constitute the provisions of this standard through reference in this standard. When the standard is published, the versions shown are valid. All standards are subject to minor revisions. The possibility of using the new version of the sub-standard will be discussed in the preparation of this standard. G8/71443-1996
Self-clamping chain for machine tools and engineering toolsbZxz.net
7:24 Joint drawing of the machine tool
GH/3837.31983
GH4133—1984
3 Type and size
The type and size of the forced transmission of Morse's circle are as follows: Figure a
Its En frequency
Note: The shape and shape of the nail are not designed as a small example. Approved by the State Machinery Industry Bureau on May 20, 1999 and implemented on January 1, 2000
7: 24
The medical four rows and
.RT3411.104-1999
17: 24 The exact size and shrinkage difference (regulations of Japan/T38.37.3. The size and difference of Morse mesh chain are in accordance with the current provisions of GB4133: 4 marking
Marking example:
Outer chain 7: 21 mesh 40, inner chain 4 7: 24 mesh chain forced transmission hall intermediate sleeve intermediate sleeve
40-4.IR/T34t1.1041999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.