This standard specifies the product classification, method, inspection rules, marking, packaging, transportation and storage of non-substrate polyvinyl chloride plastic roll floor (hereinafter referred to as plastic floor). This standard is applicable to plastic floor with polyvinyl chloride resin as the main raw material, added with plasticizer and other additives, and calendered and printed. QB/T 1647-1992 Non-substrate polyvinyl chloride plastic roll floor QB/T1647-1992 Standard download decompression password: www.bzxz.net

Industry Standard of the People's Republic of China
Polyvinyl fluoride plastic roll floor without substrate
Subject content and scope of application
QB/T 1647---92
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of polyvinyl chloride plastic roll floor without substrate (hereinafter referred to as plastic floor). This standard applies to plastic floor made of polyvinyl chloride resin as the main raw material, with plasticizers and other additives added, through calendering, printing, compounding and other processes.
Cited standards
GB2828
GB2918
GB 4085
GB 6672
GB6673
GB 8808
GB13022
QB1127
Product classification
Batch inspectionCount sampling procedure and sampling table (applicable to inspection of continuous batches)Standard environment for conditioning and testing of plastic specimensSemi-rigid polyvinyl chloride block plastic floor
Determination of thickness of plastic film and sheetMechanical measurement methodDetermination of length and width of plastic film and sheetPeel test method for soft composite plastic materialsTest method for tensile properties of plastic film
Soft polyethylene printed film
Classified by foaming and non-foaming, see Table 1.
Technical requirements
4.1 Specifications
4.1.1 Width and deviation shall comply with the provisions of Table 2. Approved by the Ministry of Light Industry of the People's Republic of China on January 15, 1993 388
Two-layer composite foam
Three-layer composite foam
Two-layer composite non-foam
Three-layer composite non-foam
Main uses
Automobile
Interior decoration
Automobile
Interior decoration
Implementation on September 1, 1993
≥1300
QB/T 1647—92
Superior products
The number of sections per roll, the minimum section length and the roll length deviation shall comply with the provisions of Table 3. Table 3
Roll length, m
25～30
Superior product
Note: The positive deviation of roll length is unlimited,
Roll length deviation, %
First-class product
Qualified product
4.1.3 Thickness and deviation shall comply with the provisions of Table 4. Category
4.2 Appearance shall comply with the provisions of Table 5.
Pattern
Bubble, perforation, delamination
Wrinkle, concave-convex, black spot, impurity
Roll end misalignment, mm
Color misalignment
More than four colors
4.3 Physical and mechanical properties shall comply with the provisions of Table 6. Superior products
Number of sections, sections
First-class products
Qualified products
Superior products
Thickness and
Superior products
Qualified products
Minimum section length.m
. Superior products
Qualified products
Qualified products
Qualified products
Basically clear
Tensile load, N
Elongation at break, longitudinal and transverse, %
Peeling load.N
Dimensional change rate after heating, longitudinal and transverse
direction, %
Heating loss rate, %
Test method
Superior products
≥100
QB /T1647—92
Qualified products
Superior products
1.0/≤1.5
5.1 Standard environment for specimen condition adjustment and test ≥30
≥150
≥120
≥220
First-class products
≥110
≥200
Qualified products
≥130
≥100
≥180
Superior products
·Class products
Qualified productsbZxz.net
The test shall be carried out according to the normal deviation range of the standard environment in GB2918. The condition adjustment time shall not be less than 8h, and the test shall be carried out under this condition. 5.2 Sample preparation
Cut a sample of about 0.6m or more from at least 300mm away from one end of the plastic floor as a sample. See Figure 1 for sample cutting. o
Figure 1 Schematic diagram of sample cutting
1--Tensile load and elongation at break sample; 2-Heating size change rate sample; 3-~Heating loss rate sample; 4-…Peeling load sample 5.3 Specifications and deviations
5.3.1 Width shall be in accordance with the provisions of GB6673. 5.3.2 Thickness shall be in accordance with the provisions of GB6672. 5.3.3 The deviation of the length of the small section and the length of the roll shall be measured with a measuring tool with an accuracy of 1mm. 5.4 Appearance
Visual inspection under natural light; color misalignment shall be in accordance with the relevant provisions of QB1127, and the end face misalignment shall be measured with a measuring tool with an accuracy of 1mm. 5.5 Tensile load and elongation at break
According to the provisions of GB13022. Use type 1 test specimen, the speed is 100 ± 10mm/min. 5.6 Residual load
Perform according to the provisions of GI38808. For composite products with blue layer, the surface layer and the middle and bottom layers, the surface, middle and bottom layers shall be tested separately, 390
5.7 Heating dimensional change rate and heating loss rate QB/T1647-92
Perform according to the relevant provisions of 4.6 and 4.7 in GB4085. 6 Inspection rules
6.1 Batch
Products shall be accepted in batches. Plastic floorings with the same specifications, formulas and patterns are considered as a batch, and each batch shall not exceed 2000 rolls. 6.2 Factory inspection
Perform according to the provisions of Chapter 4.
6.3 Sampling
Random sampling is performed in each batch.
6.3.1 Sampling of specifications and appearance shall be carried out in accordance with the provisions of Table 2 and Table 3 of GB2828. 6.3.2 Physical and mechanical properties inspection is carried out in batches, and 0.6m of a roll is randomly selected from each batch for inspection. 6.4 Judgment rules
6.4.1 Judgment of sample unit quality
Specifications and appearance shall be inspected in accordance with the requirements of 4.1 and 4.2. If all items are qualified, the sample unit is qualified. 6.4.2 Determination of qualified batches
Specifications and appearance shall be in accordance with the provisions of Table 2 and Table 3 of GB2828, and a normal inspection sampling plan shall be adopted. The general inspection level is ", and the qualified quality level (AQI.) is 6.5.
For the physical and mechanical properties test results, if there are unqualified items, double samples should be taken from the original batch again, and the unqualified items should be re-inspected. If all the re-inspection results are qualified, the entire batch is qualified. 6.4.3 Determination of product grade.
Determine according to the lowest grade of all test results. 7 Marking, packaging, transportation, storage
7.1 Marking
Each roll of product should have a certificate of conformity, including product name, specification, grade, this standard number, factory name and address, trademark, production date and inspector code.
7.2 Packaging
The product is packed with kraft paper or woven bags, or as agreed by both parties. 7.3 Transportation
During transportation, it should be protected from sunlight and rain, mechanical collision should be avoided, and loading and unloading should be done with care. 7.4 Storage
Plastic flooring should be stored indoors, kept ventilated, dry, and away from heat sources. Stacked neatly, the stacking height should not exceed 10 layers. The storage period should not exceed one year from the date of production. Additional remarks:
This standard was proposed by the Quality Standards Department of the Ministry of Light Industry. This standard is under the jurisdiction of the National Plastic Products Standardization Center. This standard was drafted by Guangdong Plastics and Leather Industry Corporation and Gaoming Plastic Factory No. 2. The main drafters of this standard are Lin Runmei, Li Hanxi, Zheng Rihong, and Chen Zhuzi. This standard adopts the Japanese Industrial Standard JISA5707-1990 "Polyvinyl Chloride Plastic Flooring". 391
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.