This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules and markings, packaging, transportation and storage of shunting winches. This standard applies to motor-driven shunting winches, which are mainly used for the shunting of ground trains. JB/T 3767-1992 Shunting winch JB/T3767-1992 Standard download decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of China
JB/T 3767-92
Shunting winch
1992-07-14 Issued
Ministry of Machinery and Electronic Industry of the People's Republic of China
1993-07-01 Implementation
Mechanical Industry Standard of the People's Republic of China
Shunting winch
1 Subject Content and Applicable Scope
JB/T 3767-92
Replaces JB3767--84
This standard defines the type and cost parameters of shunting winches, requirements, verification methods, inspection rules and markings, packaging, transportation inspection and storage. This standard applies to motor-driven two-car winches (hereinafter referred to as special extension cars) on the ground train. +2 Monthly Standard
GB10096
GB/T 133C6
GBT 354
JB/ZQ1022
Determination of sound power level of production source
Simple station
Energy-saving gear resistance
Machine products include passing technical conditions
Patrol drawing to concave wheel
Mining machinery products quality
JB/7Q1023
Mining maintenance product problem inspection and evaluation
Type and basic parametersbzxz.net
The working mechanism of the car is a friction transmission mechanism with a wheel transmission. Model marking method
Silk making net energy kN
·Comparison car
Rolling machine case
Military rubbing and snatching (single share without marking)
Marking indicator:
Single magic wheeled shunting car with a static load of 200kN is indicated by: JC2 Zhang 200 fuel type thank you car is indicated by: 2003.3 The basic 4 parameters are in accordance with the provisions of Table 1, approved by the Ministry of Electronic Industry of Hangzhou on July 14, 1992 and implemented on July 1, 1993
Comparison car heart
Sail silk Na
Public selection tiger according to the title and safety
4 Technical requirements
JB/F 3767--92
JC - 200
290-200
JC -250
3JC2GO
0.67~-0.24
6×369W+F
JC-SOC
The actual product is in accordance with the provisions of this standard and is manufactured according to the national samples and technical documents approved by the prescribed procedures. JC-50
2JC-500
4.2 All raw materials, outsourcing, and foreign companies shall be responsible for the qualified product inspection: special sample testing or inspection according to the machine standard shall be carried out in a timely manner, and can be put into use only after being recognized as qualified
4.3 The dynamic characteristics of the wheel are in line with the current national (1 industry) standards, and the speed shall not be lower than level 8-8-7. The total speed of the line 4 is 4.14×10--6.06×10m/a, and the dynamic viscosity is 2.804.4
×10-3.52×10m/s. The maximum temperature of the wheel load during operation shall not be greater than A) The temperature rise during operation shall not be greater than 3 times that of the load on the wheel. The special limit of the speed reducer is in accordance with the provisions of Table 2. 2
JC-14n
2JC-140
2JC-200
JC-250
2JC-250
4.9 The parts shall not have defects such as looseness, pores, yarn limitation and cracks that affect the strength of the car: 4.10 The design shall not have cracks, deformation, folding, spinning mold and other defects that affect the waist. 4.11 The welded parts shall not have defects such as weakness, fatigue, burn-through, etc. tt||JC-500
2JC-600
4.12 The paint pre-painted surface will be removed and the vaporized skin, nodules, etc. will be removed. The surface quality of the enterprise shall meet the requirements of JB/ZQ1022. 4.13 The enterprise standard of the car is used
day, grain car (not expected wire rope)
Control writing:
peach pole live cow, bracket treatment single, support liquid, word rolling, surface pass, flat turn, guide wheel Sichuan production equipment needs milk order).
5 Try some methods
5.1 Test case
JB/T 3767-92
5.11 Tests shall be carried out in accordance with the special test conditions. 5.1.2 Tests shall be carried out in accordance with the special test conditions. All the measuring instruments and equipment shall be within the effective measurement limits. 5.2 Empty load comparison test
Run the vehicle forward and reverse for 2m, check the sealing parts, check the connection and the contact accuracy of the wheel pair. 5.3 Negative wheel test
After the no-load test, wind 35~ turns of wire at the end of the system. 6. Determine the static tension of the wire with speed, and determine the flow rate: d. Check whether the vehicle has abnormal sound and vibration. Determine the vibration rate according to the method specified in item 3768: e. Observe the winch air suspension test process, and if the lubrication oil is 8, For example, if the oil drips from the bottom of the engine body, the surface is reversed, and there is no reverse flow, which is determined as the cleaning activity of the speed controller. The lubricant in the speed controller is discharged, and then the gas is discharged from the filter. The amount of dirt collected by the cooling device is 20mm, which is the cleaning activity of the speed controller. 6 Inspection rules
61 Each vehicle must be inspected by the manufacturing inspection department before it can be issued. 6.2 Inspection is divided into some and type inspection
6.2.1! a. Check whether the requirements of 4.13 and 7.1 are met through external regulatory control: b. Check whether the product size meets the requirements of 4.3.1.7. 6.2.2 Type inspection In addition to the contents of factory inspection, the product should also be inspected to see whether it meets the requirements of 8.3.45.461.8 a. The product has made significant improvements in design, process and even product performance within two years of production: tt.5 Two technical inspection agencies provide some requirements for type inspection. 6.3 Purchasing regulations
6.3.1 Products that meet the requirements of Article 5.2.1 are considered qualified products. 63.2 If the overall results of the plastic cavity are not in accordance with the requirements of this standard, additional inspection and testing should be carried out. The final product must be marked. Packaging, transportation, storage
7.1 Each vehicle should be marked with appropriate product labels. The label type should comply with the requirements of GB/T1306 and indicate the following:
a. Manufacturer name and trademark;
b. Product name, Plastics ;
C: Main technical parameters:
Factory vehicle, manufacturing
7.2 The packaging of the vehicle shall comply with the provisions of CB/T133S1 Attachment 7.3 The vehicle shall be equipped with the necessary fluids or the required equipment for transportation, 3
4 The following documents shall be delivered:
a: Product certificate:
. Product manual:
c. Installation order,
7.5 The bottom of the winch shall be stored in a safe place or in a well, 8 Warranty
JB/T 376792
The user shall, under the conditions of adverse transportation, installation, protection and convenience, from the month of manufacture! Within one year from the month of loading or within half a year after installation and use, if the product cannot work normally due to poor manufacturing quality, the manufacturing unit shall make no repairs or replacements. Additional Notes:
This standard is proposed by the old mechanical and electronic industry Luoyang Mining Machinery Research Institute, and the mouth of the Xuzhou Mining Equipment Manufacturing Plant is responsible for the wide grass. This standard is marked with the hand from China, quality, Zhang Shangxin
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.