QB/T 2504-2000 Industrial sewing machine flat head buttonhole sewing machine head
Some standard content:
Classification No. 17
Registration No. 7810-2DD1
Light Industry Industry Standard of the People's Republic of China
QB/F2504-2000
Industrial sewing machine
Flat head buttonhole sewing machine head
2000-12-01 Issued
State Bureau of Light Industry Issued
2001-06-01 Implementation
QB/T2504--2000
No standard The original national standard 3B121-1989 was converted from the light industry document No. [1999.1112] to the industry standard Q/F1715999, the content remains unchanged. The following aspects have been revised: the sewing speed is adjusted to 25 needle/mlm, the height of the presser foot is adjusted to 6mm. The folding performance has been added with 5.2.3 "loosening thread effect"; the chain elasticity has been added with 5.3.5; the running performance and starting quietness have been improved: 5.4.3 "there is no falling off of parts during the running process of the machine". This standard was proposed by the National Bureau of Industry and Commerce of China: the standard was issued by the National Sewing Standardization Center, and the entire standard should be initiated by: the Industrial Sewing Factory of the company, the Institute of Industrial Methods, Dalian Clothing Tailor Factory, and the main initiators of this standard are Gao Dui, Guo Zhushu, and Li, all of whom implemented it themselves. The original national industry issued the temporary industry standard QB/1371S--[991 Industry Sewing Example Flat Head Button Seam Correction Machine Head Waste Allowance
HYIKA NEYKca-
1 Scope
Light Industry Standard of the People's Republic of China
Industrial sewing machine
Flat-head buttonhole sewing machine head
QB/T2504-200G
Generation Q8T$7151999
This standard specifies the definition, classification, requirements, test methods, inspection rules and marking, packaging, storage and storage of industrial sewing machine flat-head buttonhole sewing machine heads. This standard is applicable to the sewing machine heads (hereinafter referred to as "heads") for special flat sewing machines used in the industries of clothing, textiles, inner length (including inner length) and so on.
2 Referenced standards
International standards contain clauses, which constitute the clauses of this standard through reference in this standard. The standards shown in the table are effective at the time of publication: All standards will be revised. The party using this standard should use the latest version engraved with the following mark.
32828--1987 Batch inspection and sample number certificate for small continuous batches, GB2829-1987 Periodic inspection and sampling table for stability inspection of production GT619S6 braid t. Packaging
1B3/［4515-1984 Burning flow and distribution UB/ [177-199]
Test method for noise level of sewing machines in the industry
QB/T2251-1995 Model compilation rules for the whole plate row shop dynamic rotation test method 3 Definition
This standard adopts: Meaning:
3. 1 The straight total hole of the lock type line is the basic principle of the support. 3.2 The length of the lead hole is the length of the hole in the support.
3. 5 The width of the hole refers to the total width of the group.
3. 4 Check the conclusion
Use real thread chain, fold seam, warm thread seam or other chemical short money: strengthen the effect of the braided calcium purple seam and the wooden Rui or sew a specific reverse continuation (see 1).
Little know more
Before seeking medicine
Then follow the method
Baojia Light Industry Bureau 2000-12-C1 standard
Tao1 will sketch map
Draw more,
200:-06-01 implementation
3.5 Yellow row
QB.T2504—2030
The wound hole is symmetrical on both sides and supported and added. According to the child's symptoms, it is divided into the horizontal row and the right horizontal row. $.6 Two-angle stitch
The needle and thread are straight and connected above the light hole (first picture). 3. 7 Ping Ranxun
Counting line has upward lead and side interlacing and continuous shifting (free Figure 2) March Record
Figure 2 Schematic diagram of line trace
4 Classification
The wood machine is a platform machine, which adopts connecting rod to pick up the line, external sweeping swing, rotary dial marking, and upper and lower feeding to form the 3u4 line feed specified in GBT4515
4.2 Basic emblem
numbers are shown in 1.
High-pass engraving Goddess
Girl hole intensity
#: 1 type
Guayang promotion material manufacturing
Buy thread
Choosing month needle
Electric system power
4.3 classification
: 25c
6.5~48 (select according to each model)
2.3~5.5 (can be used according to each model)
11.8tex- -7.4x×36[50:808/-6)7 grid auxiliary line or chemical 2F line GC×5 type Nm75~110(1PF:
4.3.1 According to the different etiquette (length), it can be divided into: a) hole specification 6.5mm~19mm1 type (1/4im~3/4m) b) grid 13~22.5mm: n--7/)
suitable for measurement of demarcation control, internal change industry, etc. , Applicable to the clothing industry, etc.:
c] I size 22.5mr~32mm [T1 type (7/8jn11/4m) d hole 32mm1~4mm type 4~178)
4.3.2 The material of the product technology group is divided into: -+TYKNrKAea
Applicable to the work clothing industry, etc.:
Applicable to the bedding industry, etc.
QB/T 2504--2CC0
General general materials (basic type) various types of woven and interwoven clothing materials: b braided! 4.3.3 The button forms are divided into:
; the lower head hole is flat, the basic type of knot is flat, the front hole can be used as a set, and the set product is a set hole shape. The front knot of the machine head should be uniform, and the rear knot should be changed or knotted (see Figure 3). 5.1 Appearance 511 The surface of the painted parts should be neat and uniform in color, and the paint should not be bubbling or falling off. 6.1.2 The surface of the machine head should be shiny and free of stains. The labels should be intact and decorated without obvious damage. 6.1.3 The exposed parts of the machine head should not have hair, nail heads, etc. 51.4 The surface of the plating should be smooth and uniform in color, without any spots or corrosion. 5.1.5 The color of the product shall be uniform without white sediment, heat spots, rubbing and other hazards. 6.2 Machine performance
21 The buttonhole length, front quality change, old heart, cutting position, line force, presser foot pressure and other system requirements shall be strictly adjusted
5.2.2 The lifting height shall be as specified in the table, and the action shall be included. 5.2.3 After parking, the cable pressing right should be required, 5.2.4 The correct section key ratio should be able to account for the dynamic cutting, broken needle carrier bottom stop mark, 5.2.5 After the hole is corrected, the planned lifting should be able to run the line and the orange line by itself, and the actual calculation line: 5.26 and other general stomachs should be confirmed to be effective
5.3 Seam performance
Technical G.3 and Table 2 meet the test conditions and pass the seam performance test Hc, the line trace should be eliminated: no filter needle, Si needle, empty, floating line and broken line.
5.3.1 The hole should be cut half-even, and the two horizontal rows should not be signed 5.3.2 The length of the end thread head left by the worker should not be too long! 2.5mm: The length of the thread end in the buttonhole should not exceed 5mm.
5.3.3 The flat thread can be used to sew the holes and the triangular holes.5.3.4 The 11 buttonholes are sewn through the seam.
5.3.5 The thin chain thread!
Through steel 0 buttonholes
Continuous steel 50 rises
6.3.6 Continuous avoidance
5.4 Operation performance
5.4.1 Operation
QB/T2504--2000
The speed is reduced and there is no abnormal sound. b) The intensity of the strong production is not greater than 84 (A). 5. 4.2 Fixed speed range
When the device is loaded, the maximum starting speed is not more than 1N·m: 5.43 There should be no parts sticking and parts falling off during the operation of the device. 5.5 The accessories and parts of the mother table and the spare parts should comply with the instruction manual or installation list. 5 Test method
61 outer double quality single
attachment degree is 600x=200x light, the inspection distance is 300mm, and the visual judgment is made. .2 Mechanical performance
E.2.1 Mechanism adjustment function
In the chain performance test, use the method specified in the product for adjustment. 6 2. 2 Please increase the pressure to or the commercial position, use the military regulations in a small environment and can freely adapt to it, 6. 2. 3 grid line work, 1
sequence two months after the industry was reduced by the price system,
solve the red parts in the energy test micro-standard white movement to rise, break the line product, production piece stop 6.2.5 automatic line
film test in the driver's test judgment
5.2. 5 cumulative parking
non-whole cow energy test in the light production to let the original degree, emergency rate car, H excitement standard (speed machine response emergency storage 3.3 engine sensitive energy
a) before the test, wipe the head clothing surface clean, and active risk counting board, feed plate, line parts and shear calibration! New products, lubricate and run for 5 minutes, according to Table 2 pre-test: b) Avoid red light sensitive speed meter test, test sewing speed difference is -3; before the test, fill in the details of the length, hole cutting, selection, stop, test sewing, test: no adjustment
6. 3. 1 Uniform performance
After the buttonhole is finished, it is related to the strong connection.
5. 3. 2 Thread cutting performance
After the buttonhole is finished: use a vernier card with a graduation letter of 0.02mm to measure the thread end intersection on the material. 5. 3. 3 Buttonhole thread reverse compensation
scientific judgment,
6. 3. 4 Ordinary sewing
hundred heat judgment.
5.3. 5
-FYT KANE KAa-
Day judgment.
E.3.E Continuous chain sewing
『Tide judgment completed.
Other test items
Ban hole K skin
Hole width
Floating through cutting
Seam sewing
Continuous sewing
3.4 Lightweight performance
3 4. ： Operation seepage
Attached 95xX
13(6083)
Chen Ranzhan
Q/T 2504--2000
130 No. cloth
65:635
interweaving bright source
305XLK
13n-city
a different, out of ear listening method;
b) call the city gas level: according to QB/T!?7 line: "row of capital cut oh words.
5.4.2 start the transfer
E, in the noise or after the test line:
horizontal row system firm most people width, hall want
according to QR/T2252 note
d row of the transfer,
5.4.3 machine light and Lee parts off the road
in 5.5 The whole sewing performance and language transfer performance test acceptance is difficult for the user to determine the spare parts. The parts are not supported or the assembly order requires the number of points to be withdrawn item by item. Inspection rules: Machine F specifications according to the maximum size of the sea type: large and thick holes, two angles and shallow learning: 71 The factory product quality inspection department shall inspect the product, and attach a qualified inspection certificate. There should be 5 random hole chain samples at the foot of the land, and the size can be selected by each enterprise. 7.2 Inspection classification: Product inspection is divided into type inspection and type inspection. 7.2 1 Type inspection: When the product leaves the factory, the product shall be inspected and corrected with the inspection items specified in this standard. If there are any requirements, the supply and demand parties shall coordinate and decide.
7.2.2 Type inspection
When any of the following situations occurs, a type inspection shall be carried out in the south, and a comprehensive assessment of product quality is required; 5
QH/T 2504·2000
New products or products transferred to the factory for production trials and type identification; b Formal production and product transfer, when there are major changes in the structure, materials, and process, which may affect the product performance; 2 Normal production--an annual periodic inspection shall be carried out: 3 When the product is discontinued for a long time and is about to resume production: 4 When the factory inspection result is significantly different from the last type inspection, the superior supervisory agency shall conduct a type inspection for the requirements of 7.3 Inspection items, non-conforming structure classification and inspection classification see Table 3. Table 3
Inspection source gate
5.1.1 Ball parts to the two single
5.1.2 Machine to measure
Electric parts table value quality
Thinking parts have two benefits
Price section design
Exciting
Self-station line
Cut
5.3.3 Machine hole liquid speed inflammation
5.3.6 Continuous line
5.1.1 Element abnormal activity
5.4.2 User dynamic transfer
5.4.3 Machine transfer and zero removal
Three 5 accessories and exemption
7.4 Mountain! Inspection plan
7.4.1 Column sample
Group sample is taken from the designated inspection batch. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once as shown in Table 4, strictly follow the provisions of GB/2828-198? 4.6. 4.3 The qualified and unqualified batches are determined based on the sample materials. If the number of Class A unqualified products and the number of Class B unqualified products are less than or equal to the qualified number (of products), the batch under inspection is judged to be unqualified. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa3. Sensitive performance
a) Before the test, clean the top of the garment, and check the meter plate, feed plate, thread passing part and trimmer! For new fabrics, lubricate them and run for 5 minutes. Perform the pre-test according to Table 2: b) Avoid red light sensitive speed meter test. The test sewing speed difference is -3;) Before the test, fill in the details of the length, hole cutting angle, tension, stop force, and test sewing. The test method is: no adjustment is allowed
6. 3. 1 Uniform performance
After the buttonhole is locked, the thread ends left on the material are measured with a vernier card with a graduation of 0.02mm. 5.3.3 Buttonhole thread reverse repair type
Scientific determination,
6.3.4 Ordinary sharp sewing
Hundred heat determination.
5.3.5 Continue to
-FYT KANE KAa-
Day determination.
E.3.E Continuous chain sewing
『Tide determination.
Other test items
Ban hole K leatherbzxz.net
Hole width
Floating through cutting
Seam sewing
Continuous sewing
3.4 Lightweight performance
3 4. ： Operation seepage
Attached 95xX
13(6083)
Chen Ranzhan
Q/T 2504--2000
130 No. cloth
65:635
interweaving bright source
305XLK
13n-city
a different, out of ear listening method;
b) call the city gas level: according to QB/T!?7 line: "row of capital cut oh words.
5.4.2 start the transfer
E, in the noise or after the test line:
horizontal row system firm most people width, hall want
according to QR/T2252 note
d row of the transfer,
5.4.3 machine light and Lee parts off the road
in 5.5 The whole sewing performance and language transfer performance test acceptance is difficult for the user to determine the spare parts. The parts are not supported or the assembly order requires the number of points to be withdrawn item by item. Inspection rules: Machine F specifications according to the maximum size of the sea type: large and thick holes, two angles and shallow learning: 71 The factory product quality inspection department shall inspect the product, and attach a qualified inspection certificate. There should be 5 random hole chain samples at the foot of the land, and the size can be selected by each enterprise. 7.2 Inspection classification: Product inspection is divided into type inspection and type inspection. 7.2 1 Type inspection: When the product leaves the factory, the product shall be inspected and corrected with the inspection items specified in this standard. If there are any requirements, the supply and demand parties shall coordinate and decide.
7.2.2 Type inspection
When any of the following situations occurs, a type inspection shall be carried out in the south, and a comprehensive assessment of product quality is required; 5
QH/T 2504·2000
New products or products transferred to the factory for production trials and type identification; b Formal production and product transfer, when there are major changes in the structure, materials, and process, which may affect the product performance; 2 Normal production--an annual periodic inspection shall be carried out: 3 When the product is discontinued for a long time and is about to resume production: 4 When the factory inspection result is significantly different from the last type inspection, the superior supervisory agency shall conduct a type inspection for the requirements of 7.3 Inspection items, non-conforming structure classification and inspection classification see Table 3. Table 3
Inspection source gate
5.1.1 Ball parts to the two single
5.1.2 Machine to measure
Electric parts table value quality
Thinking parts have two benefits
Price section design
Exciting
Self-station line
Cut
5.3.3 Machine hole liquid speed inflammation
5.3.6 Continuous line
5.1.1 Element abnormal activity
5.4.2 User dynamic transfer
5.4.3 Machine transfer and zero removal
Three 5 accessories and exemption
7.4 Mountain! Inspection plan
7.4.1 Column sample
Group sample is taken from the designated inspection batch. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once as shown in Table 4, strictly follow the provisions of GB/2828-198? 4.6. 4.3 The qualified and unqualified batches are determined based on the sample materials. If the number of Class A unqualified products and the number of Class B unqualified products are less than or equal to the qualified number (of products), the batch under inspection is judged to be unqualified. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa3. Sensitive performance
a) Before the test, clean the top of the garment, and check the meter plate, feed plate, thread passing part and trimmer! For new fabrics, lubricate them and run for 5 minutes. Perform the pre-test according to Table 2: b) Avoid red light sensitive speed meter test. The test sewing speed difference is -3;) Before the test, fill in the details of the length, hole cutting angle, tension, stop force, and test sewing. The test method is: no adjustment is allowed
6. 3. 1 Uniform performance
After the buttonhole is locked, the thread ends left on the material are measured with a vernier card with a graduation of 0.02mm. 5.3.3 Buttonhole thread reverse repair type
Scientific determination,
6.3.4 Ordinary sharp sewing
Hundred heat determination.
5.3.5 Continue to
-FYT KANE KAa-
Day determination.
E.3.E Continuous chain sewing
『Tide determination.
Other test items
Ban hole K leather
Hole width
Floating through cutting
Seam sewing
Continuous sewing
3.4 Lightweight performance
3 4. ： Operation seepage
Attached 95xX
13(6083)
Chen Ranzhan
Q/T 2504--2000
130 No. cloth
65:635
interweaving bright source
305XLK
13n-city
a different, out of ear listening method;
b) call the city gas level: according to QB/T!?7 line: "row of capital cut oh words.
5.4.2 start the transfer
E, in the noise or after the test line:
horizontal row system firm most people width, hall want
according to QR/T2252 note
d row of the transfer,
5.4.3 machine light and Lee parts off the road
in 5.5 The whole sewing performance and language transfer performance test acceptance is difficult for the user to determine the spare parts. The parts are not supported or the assembly order requires the number of points to be withdrawn item by item. Inspection rules: Machine F specifications according to the maximum size of the sea type: large and thick holes, two angles and shallow learning: 71 The factory product quality inspection department shall inspect the product, and attach a qualified inspection certificate. There should be 5 random hole chain samples at the foot of the land, and the size can be selected by each enterprise. 7.2 Inspection classification: Product inspection is divided into type inspection and type inspection. 7.2 1 Type inspection: When the product leaves the factory, the product shall be inspected and corrected with the inspection items specified in this standard. If there are any requirements, the supply and demand parties shall coordinate and decide.
7.2.2 Type inspection
When any of the following situations occurs, a type inspection shall be carried out in the south, and a comprehensive assessment of product quality is required; 5
QH/T 2504·2000
New products or products transferred to the factory for production trials and type identification; b Formal production and product transfer, when there are major changes in the structure, materials, and process, which may affect the product performance; 2 Normal production--an annual periodic inspection shall be carried out: 3 When the product is discontinued for a long time and is about to resume production: 4 When the factory inspection result is significantly different from the last type inspection, the superior supervisory agency shall conduct a type inspection for the requirements of 7.3 Inspection items, non-conforming structure classification and inspection classification see Table 3. Table 3
Inspection source gate
5.1.1 Ball parts to the two single
5.1.2 Machine to measure
Electric parts table value quality
Thinking parts have two benefits
Price section design
Exciting
Self-station line
Cut
5.3.3 Machine hole liquid speed inflammation
5.3.6 Continuous line
5.1.1 Element abnormal activity
5.4.2 User dynamic transfer
5.4.3 Machine transfer and zero removal
Three 5 accessories and exemption
7.4 Mountain! Inspection plan
7.4.1 Column sample
Group sample is taken from the designated inspection batch. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once as shown in Table 4, strictly follow the provisions of GB/2828-198? 4.6. 4.3 The qualified and unqualified batches are determined based on the sample materials. If the number of Class A unqualified products and the number of Class B unqualified products are less than or equal to the qualified number (of products), the batch under inspection is judged to be unqualified. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa： Operation leakage sound
Attached 95xX
13(6083)
Chen Ranzhan
Q/T 2504--2000
130 No. cloth
65:635
interweaving bright source
305XLK
13n-city
a different, out of ear listening method;
b) call the city gas level: according to QB/T!?7 line: "row of capital cut oh words.
5.4.2 start the transfer
E, in the noise or after the test line:
horizontal row system firm most people width, hall want
according to QR/T2252 note
d row of the transfer,
5.4.3 machine light and Lee parts off the road
in 5.5 The whole sewing performance and language transfer performance test acceptance is difficult for the user to determine the spare parts. The parts are not supported or the assembly order requires the number of points to be withdrawn item by item. Inspection rules: Machine F specifications according to the maximum size of the sea type: large and thick holes, two angles and shallow learning: 71 The factory product quality inspection department shall inspect the product, and attach a qualified inspection certificate. There should be 5 random hole chain samples at the foot of the land, and the size can be selected by each enterprise. 7.2 Inspection classification: Product inspection is divided into type inspection and type inspection. 7.2 1 Type inspection: When the product leaves the factory, the product shall be inspected and corrected with the inspection items specified in this standard. If there are any requirements, the supply and demand parties shall coordinate and decide.
7.2.2 Type inspection
When any of the following situations occurs, a type inspection shall be carried out in the south, and a comprehensive assessment of product quality is required; 5
QH/T 2504·2000
New products or products transferred to the factory for production trials and type identification; b Formal production and product transfer, when there are major changes in the structure, materials, and process, which may affect the product performance; 2 Normal production--an annual periodic inspection shall be carried out: 3 When the product is discontinued for a long time and is about to resume production: 4 When the factory inspection result is significantly different from the last type inspection, the superior supervisory agency shall conduct a type inspection for the requirements of 7.3 Inspection items, non-conforming structure classification and inspection classification see Table 3. Table 3
Inspection source gate
5.1.1 Ball parts to the two single
5.1.2 Machine to measure
Electric parts table value quality
Thinking parts have two benefits
Price section design
Exciting
Self-station line
Cut
5.3.3 Machine hole liquid speed inflammation
5.3.6 Continuous line
5.1.1 Element abnormal activity
5.4.2 User dynamic transfer
5.4.3 Machine transfer and zero removal
Three 5 accessories and exemption
7.4 Mountain! Inspection plan
7.4.1 Column sample
Group sample is taken from the designated inspection batch. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once as shown in Table 4, strictly follow the provisions of GB/2828-198? 4.6. 4.3 The qualified and unqualified batches are determined based on the sample materials. If the number of Class A unqualified products and the number of Class B unqualified products are less than or equal to the qualified number (of products), the batch under inspection is judged to be unqualified. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa： Operation leakage sound
Attached 95xX
13(6083)
Chen Ranzhan
Q/T 2504--2000
130 No. cloth
65:635
interweaving bright source
305XLK
13n-city
a different, out of ear listening method;
b) call the city gas level: according to QB/T!?7 line: "row of capital cut oh words.
5.4.2 start the transfer
E, in the noise or after the test line:
horizontal row system firm most people width, hall want
according to QR/T2252 note
d row of the transfer,
5.4.3 machine light and Lee parts off the road
in 5.5 The whole sewing performance and language transfer performance test acceptance is difficult for the user to determine the spare parts. The parts are not supported or the assembly order requires the number of points to be withdrawn item by item. Inspection rules: Machine F specifications according to the maximum size of the sea type: large and thick holes, two angles and shallow learning: 71 The factory product quality inspection department shall inspect the product, and attach a qualified inspection certificate. There should be 5 random hole chain samples at the foot of the land, and the size can be selected by each enterprise. 7.2 Inspection classification: Product inspection is divided into type inspection and type inspection. 7.2 1 Type inspection: When the product leaves the factory, the product shall be inspected and corrected with the inspection items specified in this standard. If there are any requirements, the supply and demand parties shall coordinate and decide.
7.2.2 Type inspection
When any of the following situations occurs, a type inspection shall be carried out in the south, and a comprehensive assessment of product quality is required; 5
QH/T 2504·2000
New products or products transferred to the factory for production trials and type identification; b Formal production and product transfer, when there are major changes in the structure, materials, and process, which may affect the product performance; 2 Normal production--an annual periodic inspection shall be carried out: 3 When the product is discontinued for a long time and is about to resume production: 4 When the factory inspection result is significantly different from the last type inspection, the superior supervisory agency shall conduct a type inspection for the requirements of 7.3 Inspection items, non-conforming structure classification and inspection classification see Table 3. Table 3
Inspection source gate
5.1.1 Ball parts to the two single
5.1.2 Machine to measure
Electric parts table value quality
Thinking parts have two benefits
Price section design
Exciting
Self-station line
Cut
5.3.3 Machine hole liquid speed inflammation
5.3.6 Continuous line
5.1.1 Element abnormal activity
5.4.2 User dynamic transfer
5.4.3 Machine transfer and zero removal
Three 5 accessories and exemption
7.4 Mountain! Inspection plan
7.4.1 Column sample
Group sample is taken from the designated inspection batch. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once as shown in Table 4, strictly follow the provisions of GB/2828-198? 4.6. 4.3 The qualified and unqualified batches are determined based on the sample materials. If the number of Class A unqualified products and the number of Class B unqualified products are less than or equal to the qualified number (of products), the batch under inspection is judged to be unqualified. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa3 Parts and components to be removed
Three 5 Accessories and exemptions
7.4 Inspection plan
7.4.1 Sample sampling
Sample samples are taken from the designated inspection batches. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once, see Table 4, strictly follow the provisions of GB/2828-198? 4.6, .4.3 The qualified and unqualified batches are determined based on the sample data. If the number of Class A non-conforming products and the number of Class B non-qualified products are less than or equal to the number of Class A non-qualified products (), the inspection batch is judged to be a qualified batch. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa3 Parts and components to be removed
Three 5 Accessories and exemptions
7.4 Inspection plan
7.4.1 Sample sampling
Sample samples are taken from the designated inspection batches. 7.4.2 Sampling plan and strictness
Unqualified classification
Inspection classification
Production inspection
Check the sample once, see Table 4, strictly follow the provisions of GB/2828-198? 4.6, .4.3 The qualified and unqualified batches are determined based on the sample data. If the number of Class A non-conforming products and the number of Class B non-qualified products are less than or equal to the number of Class A non-qualified products (), the inspection batch is judged to be a qualified batch. -Y KAN KAa-
26--15e:
151--[20(
Sample
Recommend our unit to inspect carbon number
QB/T 25C4-200C
Positive belt inspection sales·Second batch selection
Class A 4 squeeze
Level 3-2
Class not qualified
AQL-:5
2. Class A 1, R, calculated as qualified products, daily class, dead inflammation of A,, R. The unqualified products of category C are calculated based on the economic efficiency of AQL-40. If the number of A-level products and category B-level products does not correspond to the number of qualified products (or the number of qualified products of category C), the corresponding number of qualified products (or the number of qualified products) will be found in the sample, and the unqualified products and batches will be rejected according to the provisions of 4.12 of GBT2828-1987. 7.5: The sample shall be taken from the public network before the standard is lowered, and the qualified products or batches shall be guaranteed. The six rotten energy long table cloud at the same time is water.
7.6.2 site sample can travel
type of emergency inspection 03/T2829-1087 industry line, wearing sample case clothes 5
judgment plan level
select day small
trolley unit control inspection item
type non-compliant product
time pull group, see Table 5,
time group and sea
B type human heart
supplement: 1. Sample small unit for the cut head;
2. or type 4, change to non-compliant product count, type, heart inflammation 7.5.3 Type inspection qualified cabinets will not be qualified based on the live sample inspection. If the number of Class A unqualified products and the number of Class B and Class C unqualified products are both less than or equal to the corresponding number of qualified judgments (A, B, C, etc.), the type inspection will be judged as unqualified. 7.5.4 After the type inspection fails, the traces will be arranged according to 4.1 in 02829-19. 2 regulations.
5 Marking, packaging, transportation, purchase and storage
5.1 Product production has the following markings:
e) Product model:
b) Trademark;
) Product standard code:
d) Manufacturing name
e) Specific date or number.
8.2 Packaging marking
QBT2554--2030
According to the provisions of 7. in GA/16469-1996
3 Transportation and storage
According to the provisions of 7.2 in GBT 16469--1996 YY KANE KAa
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.