This standard specifies the shoe size identification method and discusses the basic characteristics of the shoe size system named after the world shoe size (Mondopoint). This standard is applicable to all types of shoes without limitation. GB/T 3293.1-1998 Shoe size GB/T3293.1-1998 Standard download decompression password: www.bzxz.net

ICs_5.060
National Standard of the People's Republic of China
GB/T3293.1—1998
idtIs0 9407:1991
Published on 1998-01-16
Shoes sizes
1998-12-01 implementation
State Technical Supervision Bureau issued
GB/T3293.1--1398
This standard is equivalent to the international standard 15)407:91, which is not the current international standard. The name of the world shoe number is Vondcpoinr) and the intermediate special requirements are based on the ministerial requirements. China's shoe products are converted into world shoe numbers and adopted international technical standards to promote the reduction of international technical economic exchanges. It is helpful to promote the development of my country's footwear industry and the development of American and Chinese products towards the international midfield standard. It is part of the intermediate Korean shoe number list. From the date of implementation, this standard will replace G329G3293-32: from now on! The standard is a reminder of the part of this standard. The standard is issued by the National Light Industry Standardization Center. The originating unit of this standard: Light Industry General Association Research Institute: This standard is issued by the National Light Industry Standardization Center. The standard was first issued in January 1982. The National Light Industry Standardization Center is responsible for the interpretation of the standard. (8,T 3293.11996
[SO Foreword
The International Organization for Standardization is a full or partial grouping of national standard-setting bodies (S standard pages). Its work is usually carried out through committees. It is an international organization with a network of members. Non-governmental organizations may also participate in the cooperation. It cooperates closely with all international committees on electrotechnical standardization. The International Organization for Standardization (IOS) is an international organization with a network of member states. Only when a member state has a vote can it issue an international standard.
International Standard 1)07:1SS1 IS/TC3Y, printed number called. This standard is the first edition developed by the committee responsible for replacing and ending with 1S0 2[:1973, IS0 3355;1573 and J50 3844:1$77,1 Scope
National Standard of the People's Republic of China
Shncs sizes
CB.T3293.11998
1d1309407.1991
Road 243
This standard specifies the number identification method and discusses the use of numbers named after the world society number (Mandcpiinl). This standard is applicable to all types of non-standard shoes without limitation. 2 Definitions
This standard uses the following meanings:www.bzxz.net
2.1 Shoc
Its meaning includes without limitation chain, missing shoes, Rui shoes and types with pieces. 2.2 Size of the shoc
The measurement value of the foot. It can provide the limit of the foot. 2.3 Foot length lengl th Pay attention to the horizontal distance between the weight line touched by the increase point of the foot and the vertical line transmitted by the limit point. The patient should stand upright (body 3 evenly distributed on both feet) and wear socks suitable for the type of sex to measure the condition. The length of the foot is measured by the soft tape. The length of the foot is measured by the soft tape. The soft tape should not be too loose or too tight, and the measuring conditions should be alternating with the foot length measuring plate. 1) Rate standard reference (Japanese 3293-note road number Ministry of National Technical Supervision Park 1998-01-16 standard 1958.: 2.01 implementation 2.5 foot light wih f cl fonsi GB/T 3293.1...1998
The projection of the group on the second plane. Represents the horizontal line between the first and fifth joints of the mesh (Figure!). The length is the same as the length of the original.
2.6-General stop avcragc normal foot According to statistical results and anatomy research, the meaning of the 3 basic characteristics of the shoe size system
3.1 The shoe size is based on the International System of Units (SI), and the two-dimensional unit system is only used in the order of the two units. 3.2 The shoe size system is based on the following full measurement appearance, ) 4 Long press 2.3 Definition
) That is, 2.5 Definition).
: The speed of exiting the well is not limited to the previous stages.
4 Method for determining the number
The number is determined by the corresponding general measurement of the foot. 5 Method for expressing the measurement value of the shoe size
The corresponding measurement value of the length and density must be meter: This regulation does not support the auxiliary indication method of the trade, and this supplement may be used for future international market reasons. 6 Marking method
61. The marking
feature of the marking should include the foot length indication, and if there are other requirements, the width indication. If all values ​​are expressed in meter integers (without indicating the period unit), they are separated by short diagonal coins,
the font width is at least 3mm, and it should be more clearly separated from other possible markings (for example, continuous sealing lines, squares or faces, etc.).
250/9+
The marked position
250/91
260/0+
G1/73293.1-1598
Each pair of shoes must be clearly marked with the appropriate position of the selected number. 6.2.2 On the packaging
When the shoes are packaged in a tray or other bag, the packaging 1 must also indicate the shoe size. 6.3
, the form of the logo
the form of the logo (punching, printing, center mark, etc.) shall be arranged by the manufacturer. The logo on the shoe should be clearly visible and effective for the time being.
7 Conversion of existing shoe size system
The current shoe size of different shoe systems is different from that of the existing shoe size system. The method is to change the existing shoe size to a length corresponding to the normal length (indicated by the crown number). Each sample number is also called the width code expressed in meters, A1
G/T3293.1-- 1998
(prompt time system)
number identification method example
shoe size can be indicated by length, the party to adjust the teaching to express, the following form: 3n/94
260-94
260-94
can be expressed by foot length and type, can also be expressed by enumeration, for example: A2
241/2 type is converted to world Korean 245 (2); Chinese shoe size
Chinese shoe size
type is converted to world shoe size 200.5),
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.