JB/T 8115.1-2000 This standard is a revision of JB/T 8115.1-95 "Paper Cutter". During the revision, editorial changes were made to the original standard and some indicators in the original standard were adjusted. This standard is part of the JB/T 8115 "Paper Cutter" series of standards. This series of standards includes the following two parts: JB/T 8115.1-2000 Paper Cutter JB/T 8115.2-2000 Paper Cutter Blade This standard specifies the classification and naming, technical requirements, test methods, inspection rules, marking, instructions for use, packaging, transportation and storage of paper cutters. This standard is applicable to paper cutters that cut various flat sheets of paper and other similar paper soft materials. This standard was first issued on October 28, 1983 as GB 3902-83, and the standard number was adjusted to JB/T 8115.1-95 in April 1996. JB/T 8115.1-2000 Paper Cutter JB/T8115.1-2000 Standard Download Decompression Password: www.bzxz.net

ICS37.100.10
Machinery Industry Standard of the People's Republic of China
JB/T 8115.1~-8115.2—2000
Paper cutter
Paper cutter
Published on April 24, 2000
National Bureau of Machinery Industry
Implementation on October 1, 2000
JB.T8115.1-200U
This standard is a revision of JR/TR115.1-95 paper cutter. Editorial changes were made to the original standard during the revision, and some of the original indicators were omitted. The overall level is equivalent to
This standard is consistent with 1R/115.! 95 main technical differences are as follows: according to the technical development and field environment changes and the requirements of the actual connection, the classification and naming, the basic parameters, the cutting accuracy, the assembly accuracy, etc. have been greatly modified, the content of the test method has been increased, and the necessary requirements have been supplemented. This standard is a sub-standard of the JB 115 cutting machine blade: This series of standards includes the following two parts: JB 8115.1-2000 || tt || JB 8115.2-2000 machine blade || tt || This standard replaces [B8115.1-95. This standard was proposed and accepted by the National Printing Machinery Standardization Technical Committee. The responsible drafting unit of this standard: Shanghai Zhongda Machinery Co., Ltd. The drafting units of this standard: Changzhe Printing Machinery Factory, Gansu Pingliang Printing Machinery Factory, Zhejiang Ruian Printing Machinery Factory The main drafters of the standard: Guo Benkuai, Tao Ziying. Drafters of this standard: Jin Yuwen, Che Wenzhe, Lin Yuehui, ■ Fan You
Machinery Industry Standard of the People's Republic of China
Paper Cutter
Paper Cutter
JB/T 8115.1-2080
JB/T 8115.I—91
This standard specifies the classification and naming, technical requirements, test methods, inspection rules, marking, as well as instructions, packaging, transportation inspection and recommendation of paper cutters.
This standard is applicable to paper cutters for cutting various flat papers and other soft materials of general paper. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of technical standards through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. The parties using this standard should explore the possibility of using the latest version of the following standards: OB 19[—1990
GB/T 1214.[--1214.4—1996
GR/T5226.1—1996
GBT6091—1985
GR/T6310—1986
GB/T6388—1986
GB/T9056—1988
GB9969 .1 — 1998 | | tt | tt||Packaging, storage and transportation pictorial signs
Vernier calipers
Industrial regulations for mechanical and electrical equipment Part I: General technical service parts Knife-shaped rulerbzxz.net
Lever dial indicator
Transportation packaging, shipping and receiving signs
Steel ruler
Industrial product instructions General test
General technical conditions for packaging of electromechanical products
.[\Industry, General provisions for product guarantee documents
Printing machinery product model compilation section
Steel tape measure
3.1 Paper cutters are classified and named according to transmission, display and control methods: a) Mechanical paper cutter
The paper cutter with main components such as the paper bed, paper pusher and paper presser as mechanical transmission. b) Pressure paper cutter
The paper cutter with hydraulic transmission as the paper presser.
Fully liquid paper cutter
Paper cutter with liquid-driven bed and paper press. Approved by the State Administration of Industry and Commerce on April 24, 20002
Implemented on October 1, 2000
d) Digital display paper cutter
JB/T8115, 1200)
The position and size of the paper pusher are displayed in digital force through position sensor) Program-controlled paper cutter
Paper cutter that uses signal recognition and memory device or micro-processor to operate according to instruction cycle 3.1 The product specifications of fiber-cutting machine are mainly based on the width of the door (1 working table width) Paper leveling machine The products are preferred to use the following specifications: 2600, 2200, 1760, 1550, t370, 1300, 1150, 920.780, 660mm, 3.3 Paper cutter model card shrinking method according to the provisions of B/300, technical requirements
paper cutter to be produced according to the standard requirements of the model, and according to the approved sample preparation department technical documents in the order specified in the cap: the basic parameters of the vertical machine are in accordance with the provisions of Table 1
Table "Basic Parameters
Width Commercial Degree
Custom Light Size | |tt||The length of the cutting seat
1 The length of the front part of the workbench
1. The height of the workbench
1 The size of the workbench (width and depth
is large
to obtain the cutting speed
Cutting speed
Standard mechanical paper cutting machine
Flow, full paper cutting machine
Mechanical paper cutting machine
Concentrated market efficiency
Gold jade paper cutting machine:
2(MXM)
240K HK
75[0-960
=s15000
Length machine (paper! The specification of the paper is to cut 100~120gm offset paper of large size, and the cutting accuracy shall comply with the provisions of Table 2. 4.3.1
Cutting line seat tolerance
Cutting adjacent edge tolerance
Continuous flattening certificate
Selection area model cutting length tolerance
Equal length within the distance
Installation accuracy
JB/T 8115.1-2000
Table 2: Cutting accuracy
Program-controlled paper cutter
Liquid cutting machine
Program-controlled cutting machine
Digital cutting machine
Reduced cutting machine
Digital paper cutter
Digital paper cutter
Pressure cutting machine
The assembly accuracy of the machine after assembly shall comply with the requirements of Table 3. Table 3 Assembly Matching accuracy
[Paper bottle surface cutting force can be original
The displacement of the pusher is only
The front effect of the press is low-profile! Description and frame matching diagram
4.5 The working table of the paper cutter with a specification of not less than 1150mm should be equipped with an air cushion chamber, and the pressure of the paper press should be able to be adjusted. 4.6
The machine runs stably, the transmission is normal, and there is no abnormal sound. 4.7
The vertical and horizontal mechanism moves accurately, flexibly and reliably, and the light card group and white hair move freely. 4.Limit
0.20/1000
129±0.15
125 ± 0.20
125 ±0.50
The door account is now available
Guarantee that the machine can only be operated under the bed 1
4.9 The brake mechanism is sensitive and reliable, ensuring that the machine can stop cutting soil when it runs to any position, and there should be no continuous force and obvious sliding knife, 10 The electrical system is safe, sensitive and reliable. 4.
The fluid system is not working, and there is no leakage. The lubrication system can work properly and the elimination path is unobstructed.
The noise should not exceed 82dBA)
Safety requirements
JB/1 8115.1-2000
4.14.1 The paper cutter must be equipped with the following safety devices to ensure that they are effective: an overload protection device must be installed, which should be effective when overloaded; 6) The paper cutter should have a single-time parking device: the knife bed must automatically stop at the bottom position after the first cutting action, and the knife bed should not have a second cutting action even if both hands are not released; there should be measures to prevent the mountain from entering the closed area when cutting, and an infrared light protection device should be installed. If the photoelectric tube beam is broken, the product stops cutting or does not start: d) The machine is equipped with a two-hand interlock device or corresponding mechanism to ensure that the two hands are operated or out of the cutting area before cutting; c) The exposed moving parts of the machine must be equipped with protection or warning area signs: d) The digital controlled paper cutter (excluding the full chain cutting machine) must be equipped with a visual device to verify the full operation of the knife bed. 4.14.2 Electrical safety performance
8 The continuity of the protective grounding circuit shall be in accordance with B/T5226.1-1996 in 20.2 provisions: h) follow the resistance report BT5226.11996 in 20.3 provisions:) cutting, test according to (B/5226.11996 in 20.4 provisions 4.15 Appearance quality
15.! The external 1 installed surface should not be rusted, misloaded, or have quality defects such as symptoms. 4.15.2 The exposed non-beating 1 old surface should not have bulges, sinks, pores, and other quality defects. 4.15.3 The coating layer is flat, and the color and gloss are uniform. The appearance of the slow film must be clear, without visible particles and adhesions, and no clear Obvious dents, paper marks, sagging, blistering, whitening and loss of gloss. 4.16 Product or set supply specification:
Paper cutter body:
b) Electric and pneumatic control equipment:
Operation and maintenance necessary tools:
d) Necessary accessories and spare parts:
) Paper cutters with a size of not less than 1150mm should be equipped with auxiliary lowering devices for users to choose (supplied by contract with the manufacturer) 5 Test methods
5.1 Inspection of basic parameters
Inspection of basic parameters should comply with the provisions of the time. 5. 2 Inspection of assembly wax degree
Inspection of assembly accuracy should comply with the provisions of the assembly 5. s. 3 Idle running test
Each paper machine product must be tested for an idle running of no less than 30m, and each cutting machine product must be tested for an idle running of no less than 6min. 5
-7
Main width
Maximum length of cutting
Minimum length of cutting cavity
Maximum height of cutting
Special department
Shenshan length
String picking method
JB/r 8115.1-2000
Table 4 Inspection of basic parameters
Permanent purpose
Front and rear digits
The meaning of the European workbench should be in accordance with the specifications of 4.2.1
Left, middle and right digits
The front table of the world test paper
The correct extension
should include the current value of 42.2| |tt||Left, middle, and storage positions
The surface of the measuring blood paper
To the ball paper, the minimum length
shall all comply with the regulations of 4.2.3
Left, middle, and storage positions
1. The maximum height of the table
shall comply with the regulations of 424
, and the front surface of the measuring blood paper
1. The K degree of the working table should meet the requirements of 42.5. Front surface of the presser, paper feeder, color paper, salt, and other height blocks. Shoot your ruler, roll celebration, paper strength, working table surface, raw paper front surface, working table front end. Surface
Steel ruler
Level checker
QF/T3859 hard
Steel tape measure
OAT9 standard
Adjustment
CB/T905G current
Steel hundred feet
Equal two pieces (equal height pieces use
GB/TL214 specified
Decomposition mark Card test
GBF9056 short-circuit
: Solution should be
1 lamp original meter
1 workbench small slot
Dragonfly pressure
Test method
Front and rear two back tests
The height of the workbench A should meet the requirements of 4.2.6
Left, middle, right, single digit
Back The measurement size of the measuring door shall comply with the provisions of 4.2.7. Under normal oxygenation, the lower barrier shall make the pressure measurement as high as possible, and the maximum value of the measured pressure shall comply with the provisions of 4.2.9. The surface of the instrument before the measurement and the minimum empty state of the measuring device shall be consistent with the provisions of 4.2.7. The fitness of the machine tool shall comply with the provisions of 4.2.9 of JEA115.12080. Table 4) Working table Pin ruler Vernier caliper Table 5 Inspection of assembly accuracy Test method Measure the direction between the front surface of the negative pressure energy device and the cutting hall In addition,
virtually meets the requirements of 4.4.1
the front surface of the pressure gauge
depth point scale
standard testing instrument
G door 9056 standard
steel ruler
GB/T1Z14 specified
mark avoidance caliper
Leli brand
non-exceeding period
accuracy: 1! The second time to test the feeder
IBAT:979, the current room
the original release
of the paper presser
is
facing
the rack
the coordination of the knife fan and the rack
is effective
to check the output force
the maintenance
will move toward the cutting area and then stop. At this
position 1, use a pulling spring
to ask the pusher to apply a pulling force of 200N. The pulling direction is opposite to the moving direction of the paper presser,
on the upper surface of the pusher!
Take the middle, right and left points respectively and use percentage to measure the position of the service. The displacement shall comply with 4.4.2. The manual low path of the rack shall comply with the provisions of 4.4.3. The self-knife shall reach the spirit wine process, and then measure the knife taste and the maximum coordination time of the rack. It shall comply with 4.4.4. F8/$11.1—2800 Table 5 (end) Tensile elastic ginger stem Percentile indicator Push trainer Five paper machine front wheat flour room ruler knife edge ruler rack equal dough knife to machine soft complete reflection Figure 1. The location of the measuring point is as follows: the meter specified in GB/T63, the plug specified in JB7979, the plug specified in GB/T6091, the room specified in JH7979, JBrT115,12q00, 5.3.1 Visually inspect the idling condition of the machine, which shall comply with the provisions of 4.5~4.12: 5.3.2 When the paper cutter is idling, use an ordinary sound level meter to measure the machine noise, the measuring point is 1m away from the outside of the machine (according to Figure 1), the height of the measuring point is (machine height + 1)2, and the average noise value obtained is the whole machine noise, which shall comply with the provisions of 4.1.3.
5.4 Safety inspection
5.4. Safety device feasibility inspection
41 Remove the blade, place a hard object of a certain height under the blade slot of the knife bed, start the machine for inspection, and the results shall comply with the provisions of 4.14.1a). b) Put both hands on the cutter button without releasing it, and the results shall comply with the provisions of 4.14.1b. 6) Use a non-transparent scale to check the middle part of each photoelectric tube, and use the blocking after starting and the blocking after starting, and the results shall comply with the judgment of 4.14.1c).
d) Perform single-handed detection operation and two-handed operation and single-handed shutdown test, and the results shall comply with the provisions of 4.14.1d). e) Measure the external moving parts of the machine. It shall comply with the provisions of 4.14.1e). 1. The sequence control relay movement should meet the requirements of 4.14.1f. 5.4.2 Electrical safety performance test
a) 4.14.2a) should be carried out according to the provisions of 4.14.2. The measured insulation resistance should meet the requirements of the batch. The test should be carried out according to the provisions of 4.14.2c. The withstand voltage test should meet the requirements of the batch. The SS cutting precision test
loading cutting precision test should be carried out according to the provisions of Table 6.
5.6 The appearance quality of the machine should meet the requirements of 4.15. 5.7 The supply range of the complete set should meet the requirements of 4.16. Inspection rules
6. Output! Inspection
6.1! Each product must be inspected and qualified by the quality inspection department of the manufacturer before it can be shipped to the factory, and the product quality certificate shall be attached. 6.1.2 Each product shall be inspected according to the requirements of 5.1, 5.2, 5.3, 5.4, 5.4.2, a) and b), 5.6, 5.7. If it fails to meet the requirements, the product shall be deemed as unqualified. 6.1.3 10% (not less than 20%) of each batch of products shall be sampled and put into 5.5. If one of the items of the sampled product does not meet the requirements, the product will be inspected again. If it still fails, the batch of products shall be sent to the station for testing. 6.7 Type test
6.21 Type test shall be carried out in any of the following situations: 1. Preliminary evaluation of new products or old products for production: 2. After formal production, such as averaging, material analysis, and major changes in the process that may affect product performance: 3. When the product is discontinued for more than three years and then resumed. 4.2.2 Type test shall be carried out according to the standard for all items. No.
Model
Straightness
Edge A
Degree tolerance
Connection
Degree error
Cut length
Within degree
Length tolerance
Inspection and supervision method
JB/T6115[-2000
Table 6 Cutting length inspection
Show diagram
With I wish you can (or both) the specified avoidance heat cutting space of 100-120gm cavity plate, select 10mil, cut - take out two adjacent sheets from the middle, turn the cutting edge over, use the reading mirror to measure the value, and calculate the H line collection difference according to the following formula in accordance with the provisions of 4.3.1: The result [or both! The paper with large hot cutting area of ​​10k% 120g/m2 is selected as the paper with a height of 10nm. The two parallel sides are obtained by positioning the folding machine, and one of them is used for heat cutting. The adjacent webs are collected, and the two sheets are collected. The two sides are aligned with the a and b sides (parallel sides) respectively. The reading microscope is used to measure the mountain value, and the vertical point difference is calculated by pressing the force. It should meet the requirements of 4.3.2: ar2
Use the specified (general requirement) large-format 100-120g/m2 version
paper and the cutting height of 20muml. Heat once every
12.5mm, and continue to study until
Use the standard caliper to measure the length of each small end
, which is the flatness difference within the range of points. Calculate the small flatness
difference according to the following formula. The 11--120g/m2 version of the specified length of the machine is cut with a high cutting height
. The cutting height is 20mm, and the width is unlimited. Continuous cutting is carried out according to the instructions given by the paper cutter. The length of each cut is 125mm. The card is used to check the actual degree of error. It should meet the requirements of 4.3.4. The cutting height is 80% of the rated height of the paper cutter. The length is 125mm, and the distance between L and the bottom is 2mm and the middle is 3 sheets. Paper sample, with vernier caliper at the same position length size, the maximum difference is the wear length, should comply with 04.3.5 of the brand provisions of feasible edge receiver reading can be set to read the microscope GB/T1214 Yao provisions of vernier caliper GB1214 original provisions of vernier caliper GB/T1214 outline provisions of the avoidance mark KR mark, use instructions section JB/T 8115.1—2000
7.1 Labeling and the contents of the instruction manual should include (listed separately: a) product name, product standard number, trademark; b) manufacturer name, detailed address, product origin; production model, main parameters; d) export number; 7.2 Marking. 1.1 Each product should be clearly labeled with a label. The label size should comply with the provisions of GB:T13306. 2.2 The packaging, storage and transportation marks of the products shall be in accordance with the relevant provisions of GB/T191. For packages with obvious lifting and center of gravity away from the center, the "export height" and "center of gravity" marks shall be marked. 7.2.3 The shipping packaging and delivery marks shall be in accordance with the relevant provisions of GB/T6388. 7.3 The contents of the instruction manual shall comply with the provisions of 9969.1. 1. For product packaging, the exposed surfaces of parts, spare parts and accessories shall be coated with anti-moisture agent, and the surfaces of main parts shall also be coated with moisture-proof agent. 8.1.2 The packaging of the product shall comply with the relevant provisions of GB/T13384. 8.1.3 Random documents When each product leaves the factory, the following documents shall be provided: a) Product certificate (the product certificate may comply with the provisions of GB/T1436) b) Product instructions; e) Packing list: Packing drawing. 8.3 Transportation When the product is transported and lifted, please lift it carefully and place it with the mark marked on the outer cover of the packaging to prevent collision. 8.3 Storage When the product is stored, it should be placed in a dry and unobstructed place to avoid traceability. If the product is stored for a long time, anti-corrosion measures should be taken. If the storage period exceeds 2 years, the packaging should be checked before leaving the factory. If it is found that the product packaging no longer meets the current standards, it should be repackaged.5. The brand definition is feasible. The whole photo receiver can read the microscope. The vernier caliper specified in GB/T1214. The vernier caliper specified in GB1214. The KR mark specified in GB/T1214 is marked. The instruction manual section is JB/T 8115.1—2000. 7.1 Marking. The content of the instruction manual should include (listed separately: a) product name, product standard number, trademark; b) manufacturer name, detailed address, product origin; core production model, main parameters; d) export number: e) product name, product standard number, trademark; f) manufacturer name, detailed address, product origin; g) product model, main parameters; g) export number: e) product name, product standard number, trademark; f) product name, product standard number, main parameters; f) product name, product standard number, main parameters; g) product model, main parameters; g) export number: e) product name, product standard number, trademark; 7.2 Marking 1.1 Each product should be clearly marked with a label, and the label size should comply with the provisions of GB:T13306. 2.2 The packaging, storage and transportation marks of the products shall be correctly marked in accordance with the relevant provisions of GB/T191. The packages with obvious lifting and center of gravity shall be marked with "height" and "center of gravity" 7.2.3 The shipping packaging and delivery marks shall comply with the relevant provisions of GB/T6388. 7.3 The contents of the instruction manual shall comply with the provisions of GB/T6388.1.2 The exposed processing surfaces of parts, spare parts and accessories shall be coated with anti-moisture agent, and the processing surfaces of major parts shall also be coated with moisture-proof agent. 8.1.2 The packaging of the products shall comply with the relevant provisions of GB/T13384. 8. 1.3 Random Documents
When each product leaves the factory, the following documents must be provided: a) Product certificate (the product certificate shall comply with the provisions of Japan/T1436); b) Product use instructions; e) Packing list:
Packing diagram.
8.3 Transportation
When the product is transported and lifted, it should be placed carefully with the mark marked on the outer surface of the packaging to prevent collision. 8.3 Storage
When the product is stored, it should be placed in a dry and unobstructed place to avoid traceability. If it is stored overnight, anti-currency measures should be taken. If the storage period exceeds 2 years, the box should be checked before leaving the factory. If it is found that the product packaging does not meet the current requirements, it should be repacked.5. The brand definition of GB/T1214 is feasible. The whole photo receiver can read the microscope. The vernier caliper specified in GB/T1214 is specified in GB/T1214. The vernier caliper specified in GB/T1214 is specified in GB/T1214. The KR mark is marked. The instruction manual section JB/T 8115.1—2000 7.1 Marking. The content of the instruction manual should include (listed separately: a) product name, product standard number, trademark; b) manufacturer name, detailed address, product origin; core production model, main parameters; d) export number: e) product name, product standard number, trademark; f) manufacturer name, detailed address, product origin; g) product model, main parameters; g) export number: e) product name, product standard number, trademark; f) product name, product standard number, main parameters; f) product name, product standard number, main parameters; g) product model, main parameters; g) export number: e) product name, product standard number, main 7.2 Marking 1.1 Each product should be clearly marked with a label, and the label size should comply with the provisions of GB:T13306. 2.2 The packaging, storage and transportation marks of the products shall be correctly marked in accordance with the relevant provisions of GB/T191. The packages with obvious lifting and center of gravity shall be marked with "height" and "center of gravity" 7.2.3 The shipping packaging and delivery marks shall comply with the relevant provisions of GB/T6388. 7.3 The contents of the instruction manual shall comply with the provisions of GB/T6388.1.2 The exposed processing surfaces of parts, spare parts and accessories shall be coated with anti-moisture agent, and the processing surfaces of major parts shall also be coated with moisture-proof agent. 8.1.2 The packaging of the products shall comply with the relevant provisions of GB/T13384. 8. 1.3 Random Documents
When each product leaves the factory, the following documents must be provided: a) Product certificate (the product certificate shall comply with the provisions of Japan/T1436) b) Product use instructions;
e) Packing list:
Packing diagram.
8.3 Transportation
When the product is transported and lifted, it should be placed carefully with the mark marked on the outer surface of the packaging to prevent collision. 8.3 Storage
When the product is stored, it should be placed in a dry and unobstructed place to avoid traceability. If it is stored overnight, anti-currency measures should be taken. If the storage period exceeds 2 years, the box should be checked before leaving the factory. If it is found that the product packaging does not meet the requirements, it should be repackaged.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.