This standard specifies the technical requirements and test methods for complete strollers. This standard is applicable to all types of strollers. QB/T 2161-1995 General Technical Requirements for Complete Strollers QB/T2161-1995 Standard download decompression password: www.bzxz.net

Industry Standard of the People's Republic of China
QB/T 2121.2122-—95
QB/T 2159~-2162—95
1995-0607 issued
1995—-10—
China Light Industry General Association issued
1996—03--01 implemented
1996—06--1
Industry Standard of the People's Republic of China
Children's Stroller
General Technical Conditions for the Whole Vehicle
CH/T2161-95
The standard is the technical requirements for the whole vehicle of child strollers. This standard is EG111.2585 short vehicle whole vehicle technical requirements. For your order, the original safety requirements of SG141-35 have been implemented (14748-334 government stroller safety requirements are in violation of the brake), this standard is no longer promoted The safety requirements of this standard refer to GB7474-1, the requirements for electric components refer to Q/T3122-5, the requirements for electric components refer to QB/T2121-95. The technical requirements for electric components refer to QB/T2121-95. The implementation date of this standard is the original light industry standard S141.25-8% standard for complete vehicle certification. This standard is proposed by the China Light Industry Federation and the National Standards Department. The Shanghai Toy Research Institute is responsible for the drafting of this standard. The main drafters of this standard are: 15.
1 Scope
Industry standards of the People's Republic of China
Technical conditions for complete children's tank cars
This standard specifies the technical conditions for complete children's tank cars
This standard specifies the technical conditions for complete children's tank cars The technical requirements and test methods for the whole vehicle. This standard is applicable to all kinds of child strollers.
2 Referenced standards
CB/T2161-95
The following standards contain clauses, and the standard structure is recorded in the standard. When the standard is published, the versions shown are valid. All standards will be ignored! All parties using this standard should use the latest version of the standard.
14745-91 Safety requirements for the whole vehicle
QP/T812 Technical requirements for electroplating of vehicles
B/F2121 Technical requirements for oil inspection of vehicles
3 Technical requirements wwW.bzxz.Net
3.1 Safety
The safety requirements for child strollers shall comply with the provisions of 117. 3.2 Introduction ||t t||3.2.1 All parts of the vehicle should be assembled correctly. 2.2.2 The welding surface should be flat without cracks, light marks, wear and tear. 3.2. The toys or any similar equipment installed on the vehicle should meet the relevant technical standards. 3.2-5 The tire sheath should be smooth and assembled smoothly. There should be no slant, buckle or bend. 3.3 Performance
3.3. For vehicles with guide wheels, the guide wheels should be flexible. 3.3.2 The auxiliary vehicle should be able to run independently. The control number 3 test should be carried out in a straight line. If the vehicle has guide wheels, there is no such test requirement. 3.3.3 The diameter and end face runout of the wheel should not be more than 3mm. 3.3.4 The folding mechanism should be stable, and the pressure should be good and the closing time should be timely. 3.3. The fabric should be firm, flat and loose. 4.5 test, the extension of 10N, the chain should not be loose or broken. 3.3.6 The vehicle should be stable. According to 4.6 test, the wheel should not be more than 5mm. China Light Industry Association 1995121 batch industry
1996-Station non-1 implementation
3.4 ​​External residual
OB/T 2161- -95
3.4.1 Oil-plated parts should meet the requirements of QB/T2121 3.2 Electroplated parts should meet the requirements of QB/T2122. 3.4.3 The surface of the sprayed plastic parts should be smooth and even, the thickness of the layer should be uniform, and no spots, stains, or color leakage are allowed. 3.4.4 Printing, decals, and patterns should be clear, complete, and solid. 3.4.5 Trademarks or marks should be installed firmly, with neat patterns and clear placement. 3.4.6 There should be no obvious color difference between the parts with the same design. 3.4. The surface of the plastic parts should be smooth and free of obvious deformation, marks, bubbles, delamination, flash, obvious layer flow, repair marks, and scratches. The color change and color accelerator that affect the appearance shall be avoided. 4. Test steps and methods
4.1 The air safety requirements shall be tested in accordance with GB14748. 4.2 Place the test heat type specified in GB14748 on the passenger part of the vehicle: on a flat surface, drive along the "" shape shown in Figure 1 to check whether it meets the requirements of 3.3.1.
4.3 Test the passenger part according to the test specified in GB14748. On a flat surface, as shown in Figure 2, pull the lead line at a uniform rate and make the vehicle run alone. Run the test three times and take the average value. Check whether it meets the requirements of 3.3.2.
Make sure the specified guide is used. The standard goods are averaged with the lead line. The vehicle drives 211 and the intersection of the four-wheel crown slip line of the vehicle is obtained! The center level is more meters. The new deviation degree of the vehicle is obtained according to the small formula. tarcig
The distance from the intersection of the front wheel line to the center of the vehicle is: OBT216195
The distance of travel, B (constant)
The four wheels are diagonally opposite or at the intersection
4.4 Install the assembled wheels on the test stand, and rotate the wheels in the test stand to check whether they are in compliance with the following parameters: 3. 3.3 Requirements. 4.5 As shown in Figure 3, use pliers with a diameter of 19 mm to clamp the joints at 12 places on both sides of the mouth as shown in National Standard 4. Use a force gauge or other simulated bone with a measuring accuracy of 3.22, and apply a tensile force of 100° in a direction perpendicular to the mouth within 5 seconds. After the tension is removed, check whether the requirements of 3.3.5 are met. 4.6 Place the cart on a test run, remove the dust-carrying parts and place them in the test pattern specified in GB14748, use a plug or other similar steel plate to adjust the straightness to 1.9 and replace it with a steel plate. Measure the maximum ground clearance of the final wheel. Check whether it meets the requirements of 3.3.6. 4.7 Other operating parts shall be tested according to Q3/T212) and chain parts shall be tested according to QB/T2122. 4.9 Other parts shall be tested according to QB/T2122.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.