This standard specifies the dimensions, tolerances and technical requirements of thrust spherical plain bearings. The structural design of thrust spherical plain bearings does not have to fully comply with the structure shown in this standard, but the dimensions and tolerances should be consistent with the provisions of this standard. This standard applies to thrust spherical plain bearings with different sliding material combinations for production inspection by manufacturers and acceptance by users. This standard does not apply to thrust spherical plain bearings for aircraft frames. GB/T 9162-2001 Spherical plain bearings Thrust spherical plain bearings GB/T9162-2001 Standard download decompression password: www.bzxz.net

TCS.2F-155.20
National Standard of the People's Republic of China
G11 91622001
eqIso12240-3.1998
Spherical plain hearings-Thrust sphcrical plaln bearings2001- 09 - 15 Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
2002-04-0T Implementation
CB/T9162-2001
This standard adopts 15)122/0-3:1998* Joint shaft ratio thrust bearing 3.15012243-3.1998, and adds the following chapters.
This standard is a revision of B/91%2-1/T33%.101985 (Part). The main revisions are as follows: ! ! The foreign service standard adopts the provisions of ISO 12240-3:1998: 2) The standard only specifies the structural type of the specified force spherical plain bearing, and the variable structure is not included in this standard from the date of implementation - the standard GB/9162-199 and GB/T1.101989 (part). This standard was proposed by the China Machinery Industry Federation. This standard was prepared by the China Rolling Bearing Standardization Technical Committee and the South China Axis Research Institute. This standard was first prepared in 1991 and has been revised for the first time since 1990. GB/T9162-2001 Foreword ISO 18012240-8 was prepared by the 150/C2 Technical Requirements Committee of the 57th Rolling Bearing Technical Requirements Committee under the China Machinery Industry Federation. 1213240 is divided into the following 4 parts: Part 1: Spherical plain bearings Part 2: Rod end bearings Part 3: Thrust plain bearings Part 4: Rod end bearings National Standard of the People's Republic of China Spherical plain bearings Thrust spherical plain bearings CB/T 9162 2001 yyLSNI12240-3:1998 [304.11: Thrusl spherical plain bearings Spheriral plain hearings This standard specifies the dimensions, tolerances and technical requirements of spherical plain bearings. The structural design of thrust spherical plain bearings does not have to fully comply with the structure, dimensions and tolerances of this standard. This standard is used for thrust spherical plain bearings of different materials. The manufacturer shall use this standard for production inspection and re-acceptance of thrust spherical plain bearings. 2 Reference standards bzxZ.net
The following standards contain the texts of this standard. The texts of the old standards are used as the standard texts. When this standard is published, the versions shown are valid. All standards will be revised. For the convenience of this standard, the parties shall explore the possibility of using the new versions of the following standards. GB—2000 Rolling bearing angular dimension expansion value ID: [S582: 1995GHr 3944—1SF3 Joint shaft hand (eqVIS6) G311:19R) GB/T19914 Definition of dynamic temperature difference (1d1501132,18) jB/18379-2001 Technical conditions for joint bonding 3 Symbols and suggestions (see Lang 1)
2 The standard adopts the definitions of GB/T344 and GB/:1196: Except for 5, the derivative numbers (tolerance specifications) shown in this standard are all nominal dimensions.
; Shaft and bearing
: Production height
1: Diameter of the drawing
4: Diameter
2.. General plastic storage
, The plane diameter of the axis drawing surface
z. Or the plane is straight
west center one-way example angle ruler
. The smallest circle and the chamfer ends at
3 The distance between the center of the sphere and the back of the sphere is again
: axis height
Vr: plane inside and outside diameter variation
Vn: average inside diameter free space
: one diameter flat outside diameter variation range
Va: single diameter flat inside diameter variation range
The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China 200109-15Approved 2012-04 -07 implementation
B. single height information
AC.; single figure this use the single academic surface flat outer diameter difference
. single inner diameter difference
engineering, bearing actual temporary compilation tea
4 outer size
shape dimension table" current determination.
GB/T9162-.2301
Figure 1 thrust bearing
thrust bearing city bearing shape reflection
You poison size
2) mountain control flow! Agriculture and fishery regulations, G/T 9162-2DC1 (table flow) 3: The relative pressure angle is the maximum direct report GD/T374--2C0C table 5 tolerances bearing tolerances according to the provisions of Table 2 and Table: Mixed coupons shaft bearing tolerances method: The tolerances of the stem values ​​in Table 1 are subject to the rate of application in the table before the joint shaft is shown in T's. The tolerances should be: Table 2 Note 6 Other technical requirements are in accordance with the provisions of 115/79, W above example difference "Dian test - 240:: 250
+ 35-1
Go to Xunlu
- 7c-1
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.