This standard applies to the safety of electrical appliances for household and similar waste food disposers with a rated voltage not exceeding 250V. Appliances that are not for general household use but may pose a danger to the public, such as appliances used by non-professionals in shops, light industry and farms, are also included in the scope of this standard. In terms of practicality, this standard deals with appliances that are dangerous to the public in the home and that may be encountered by all people. This standard does not generally consider: - appliances used by unsupervised children and infirm people; - appliances used as toys by children. GB 4706.49-2000 Special requirements for the safety of household and similar electrical appliances Waste food disposers GB4706.49-2000 Standard download decompression password: www.bzxz.net

GB4706.492000
This standard is equivalent to IEC60335-2-16:1994 Safety of household and similar electrical appliances Part 2: Particular requirements for waste food disposers. This standard should be used in conjunction with GB 4706.1-1998 General safety requirements for household and similar electrical appliances. The part of this standard marked with "applicable" indicates that the corresponding provisions in GB4706.1-1998 are applicable to this standard; the part of this standard marked with "replacement" or "modification" shall be subject to this standard; the part of this standard marked with "addition" indicates that in addition to complying with the corresponding provisions in GB4706.1-1998, it also complies with the text added by this standard. The standard is proposed and managed by the National Technical Committee for Standardization of Household Electrical Appliances. The main drafting unit of this standard is China Household Electrical Appliances Research Institute. The main drafters of this standard are Liu Qing, Wang Huirong, Li Xianli, Xu This standard is entrusted to the National Technical Committee for Standardization of Household Electrical Appliances for interpretation. GB 4706.49—2000
IEC Preface
1) IEC (International Electrotechnical Commission) is an international standardization organization composed of all national electrotechnical committees (IEC National Committees). Its purpose is to promote international cooperation on standardization issues related to electrical and electronic fields. To this end, IEC carries out international standardization activities and publishes international standards. The formulation of these standards is entrusted to technical committees. Any IEC National Committee interested in the technical issue may participate in the formulation work. International, governmental and non-governmental organizations associated with IEC may also participate in this work. IEC and the International Organization for Standardization (ISO) work closely together on the basis of an agreement between the two organizations. 2) Formal resolutions or agreements of IEC on technical issues formulated by technical committees in which all national committees with special interest in the issue participate, represent as far as possible the international consensus on the issues involved. 3) These formal resolutions or agreements are published in the form of standards, technical reports or guidelines and are accepted by the National Committees in this sense.
4) In order to achieve international consensus, IEC National Committees agree to use IEC international standards to the greatest extent possible in their national and regional standards. Standards. Differences between IEC standards and corresponding national or regional standards should be clearly marked in the latter. 5) IEC has not established a procedure for the approval mark. IEC is not responsible for any claim that a device complies with an IEC standard.
This standard was prepared by IEC Technical Committee 61 (Safety of Household and Similar Electrical Appliances). This standard constitutes IEC60335-2-16 (4th edition), replacing its 3rd edition. This standard is based on the following documents
61(CO)789
Voting Report||tt| |61(CO)801
Full material on the adoption of this standard can be found in the voting report shown above. This standard shall be used in conjunction with the latest edition of IEC60335-1 and its supplements. This standard is based on the third edition (1991) of IEC60335-1.
This standard supplements or modifies the corresponding clauses of IEC60335-1, thereby converting it into this standard: Particular requirements for food waste disposers.
IEC60335-1 clauses not mentioned in this standard may be used as long as it is reasonable. The places marked with "addition", "modification" or "replacement" in this standard are the corresponding modifications to the relevant clauses of IEC60335-1. Notes
1 This standard uses the following printing fonts: - Requirements are in regular font
- Test specifications are in italics
Notes are in small regular font
Bold words in the text are defined in Chapter 2. 2 The numbering of the clauses and figures added to this standard starts from 101. The following differences exist in some countries:
Chapter 1: The installation of waste food disposers is not allowed (Austria, Germany and the Netherlands). - Chapter 1: The installation of waste food disposers is allowed subject to the approval of the relevant authorities responsible for the local sewage system (Czech Republic, Denmark, Finland, France, Italy, Japan, Navi, Slovakia, Switzerland and Turkey). - Chapter 1: The installation of waste food disposers is allowed, subject to the decision of the relevant national authorities (China), GB4706.492000
2.2.9: Different test loads and methods are used (USA). - Chapter 3: Restriction on the use of DC components in the neutral conductor of appliances (Australia). - 6.1: Class 01 appliances are allowed (Japan). - 11.7: Different operating cycles are used (USA). - 15.2: Inappropriate test methods are used (USA). - 19.7: Different test methods are used (USA). - 19.9: Overload tests are performed (USA). 20.101: Use a different basis (USA). - 22.104: Do not perform this test (USA). 1 Scope
National Standard of the People's Republic of China
Safety of household and similar electrical appliances
Particular requirements for far food waste disposers
Safety of household and similar electrical appllancesParticular requirements for far food waste disposersGB4706.1—1998 This chapter is replaced by the following: GB 4706. 492000
idt IEC 60335-2-16:1994
This standard is applicable to the safety of household and similar food waste disposers (hereinafter referred to as "appliances") with a rated voltage not exceeding 250V.
Appliances that are not for general household use but may be dangerous to the public, such as appliances used by non-professionals in shops, light industry and farms, are also included in the scope of this standard. As far as practicality is concerned, this standard covers appliances that are dangerous to the public in the home and that may be encountered by all people. This standard does not usually consider:||tt ||Appliances for use by unsupervised children and infirm persons: - Children use the appliance as a toy.
1: Attention should be drawn to the following facts:
--Appliances used in vehicles, ships and aircraft must have additional requirements; --Appliances used in tropical areas must have additional requirements; --In many countries, additional requirements are prescribed by the national health authorities, those responsible for national labor protection, the national water supply authorities and similar authorities! The installation of food processors may be restricted and not permitted. 2 This standard is not applicable,
--Portable Waste food processors,
- Combustion type waste food processors,
Specially designed waste food processors for industrial and commercial use, - Appliances intended for use in special environments, such as environments with corrosive gases or explosive gases (dust, steam or gas). 2 This chapter in GB4706.1-1998 is applicable except for the following. 2.2.9 Replacement:
Normal operation
The storage box of the appliance is filled with 30 pieces of side length 12mm ± 2Ⅲm cube soft pine wood block. If the storage box of the appliance cannot hold all the wood blocks at the same time, the wood blocks should be added to the storage box as soon as possible during the operation of the appliance. The water temperature is within the range of (10~24)℃, and the flow rate is L/min.
2.101 Foad waste disposers are appliances installed at the outlet of the sink to reduce the particles of waste food and discharge them to the drainage system with water flow. Approved by the State Administration of Quality and Technical Supervision on March 16, 2000 and implemented on March 1, 2001
3 General requirements
This chapter in GB 4706.1-1998 applies. 4 General provisions for testing
GB 4706.49-2000
This clause in GB4706.1-1998 is applicable except for the following contents. 4.101 Except for clause 10, the normal working conditions of the appliance can be simulated by loading the appliance with a dynamometer or by blocking the outlet of the appliance and maintaining a constant water head.
5 Blank clause
6 Classification
This clause in GB 4706.1-1998 is applicable except for the following contents. 6.1 Replacement:
A waste food disposer shall be a Class I, Class I or Class I appliance. Compliance shall be checked by regulatory inspection and relevant tests. 7 Marking and instructions
This clause in GB 4706.1-1998 is applicable except for the following contents. 7.12 Added:
The following should be included in the instruction manual of the appliance: The appliance cannot be used to handle hard materials, such as glass and metal. Before the user intends to remove a stuck rotating part, the switch of the appliance should be turned off or the plug should be pulled out of the socket. If the appliance needs to work at a minimum water flow rate, this should be stated in the instruction manual. 7.12.1 Added:
The instruction manual should indicate that the appliance must be installed so that the reset button and the change-over switch are easily accessible. 8 Protection against contact with live parts
This chapter in GB 4706.1-1998 is applicable. 9 Starting of electric appliances
This chapter in GB4706.1-1998 is not applicable. 10 Input power and current
This chapter in GB4706.1-1998 is applicable except for the following contents. 10.1 Added:
Representative cycle is the cycle between (5~15)s of operation. 10.2 Added:
Representative cycle is the cycle between (5~15)s of operation. 11 Heat
This chapter in GB4706.1-1998 is applicable except for the following contents: 11.7 Replaced,
GB 4706.49-2000
Continuous loading type waste food disposer, working 4min. Intermittent loading type waste food disposer, 2min as one cycle, working two cycles, 30s rest between each cycle. 12 Void rate
13 Leakage current and electrical strength under working deterioration This chapter in GB4706.1-1998 is applicable. 14 Void chapter
15 Moisture resistance
This chapter in GB4706.1-1998 is applicable except for the following contents. 15.2 Replacement:
The construction of the appliance shall ensure that the blockage of its outlet does not affect the electrical insulation of the appliance. This shall be verified by the following test
The outlet of the appliance is blocked and the container of the appliance is filled with water to a depth of 20 cm, measured from the lowest point in the container. The appliance is powered at rated voltage and operated until the protective device operates or for 15 min, whichever is shorter. After a 15 min stop, the above test is repeated. The appliance is then subjected to the electrical strength test in accordance with 16.3 and checked for any conditions that may cause creepage distances and electrical clearances to be reduced to less than the values ​​specified in 29.1. There shall be no traces of water on the insulating surface. 16 Leakage current and electrical strength
This chapter in GB4706.1-1998 applies. 17 Over-regulation protection of transformers and associated circuits This chapter in GB 4706. 1-1998 applies. 18 Durability
This chapter in GB4706.1-1998 does not apply. 19 Abnormal operation
This chapter in GB4706.1-1998 is applicable except for the following contents. 19.7 Added:
Appliance without water operation:
Continuous charging type, work for 30s;
Intermediate peptide charging type, work for 5min.
19.9 Not applicable.
20 Stability and mechanical hazards
This chapter in GB4706.1-1998 is applicable except for the following contents. 20.2 Added:
The test finger is not applicable to the inlet of the appliance.
20.101 The appliance shall be able to prevent contact with moving parts through the open inlet. Unless a cover is installed and the motor automatically shuts down when the cover is removed.
GB 4706.49—2000
Use the gauge shown in Figure 101 to apply a force of 50N to the open inlet for inspection. The gauge cannot touch the moving parts. In addition, the distance between the top of the inlet and the moving parts should not be less than 100mm. Adjust the appliance so that the base bottom is the thinnest.
2 Removable parts should prevent waste food from being ejected or blood from falling into the moving crushing cavity. 21 Mechanical strength
This chapter in GB4706.1—1998 is applicable. 22 Structure
This chapter in GB4706.1—1998 is applicable except for the following contents. 22.101 The appliance should be equipped with a protective device, and its compliance should be checked by regulatory inspection.
22.102 The reset button of the protective device should be placed in a concealed place or protected by other means. A test specimen is used to contact the closed guard from any direction. The diameter of the test rod is (76 ± 0.1) mm and the end is chamfered:
The distance from the test rod to the button shall not be less than 1.5 mm. The guard shall be prevented from being activated by the test rod and shall not be able to reset automatically. 22.103 The construction of the appliance shall ensure that waste food cannot be ejected through the open inlet and that the guard and material chamber can be cleaned. In other tests, it is checked by visual inspection. NOTE: Water splashing from the open water inlet to a height of less than 15 crm can be ignored. 22.104 The surface material of the grinding chamber shall be able to withstand mechanical damage and the impact of waste food. It is checked by the following test.
A mild steel bar of approximately 100 mm × 12 mm × 3 mm is inserted into the grinding chamber and is inserted so that the possibility of motor stalling is reduced.
The appliance is supplied with rated voltage and operated for 15 s unless the motor initially stalls. After the test, the appliance shall comply with the requirements of 8.1.15.2, 16.3 and 29.1. NOTES
1 A test to verify resistance to corrosion by discarded food may be necessary. 2 Natural rubber is considered to be susceptible to corrosion by discarded food. 23 Internal wiring
This clause of GB 4706.1-1998 applies. 24 Components
This clause of GB 4706.1-1998 applies except as follows 24.101 Thermal cut-outs and protective devices for use with continuously charged appliances shall be non-resettable. Verified by regulatory inspection and test of clause 19. 25 Supply connection and external flexible cord
This clause of GB 4706.1-1998 applies: 26 Terminals for external conductors
This clause of GB 4706.1-1998 applies.
27 Grounding measures
This clause in GB4706.1-1998 is applicable.
28 Screws and connections
This clause in GB4706.1-1998 is applicable. 29 Creepage distances, clearances and through insulation distances This clause in GB4706.1-1998 is applicable. 30 Heat resistance, flame resistance and leakage current resistance
GB 4706. 49-2000
This clause in GB4706.1-1998 is applicable except for the following contents. 30.2 Added:
30.2.3 This clause is not applicable.
31 Rust prevention
This clause in GB4706.1-1998 is applicable. 32 Radiation, toxicity and similar hazards
This chapter in GB 4706.1-1998 is applicable. 10±0.2
Figure 101 Test specification
?0千08
Dimension unit: mm
GB 4706.49--2000
The appendices in GB 4706.1-1998 are applicable except for the following contents. Appendix C
(Standard Appendix)
Aging test for motors
Addition: Force value equal to 2000,2 Replacement:
The structure of the appliance shall ensure that the blockage of its outlet does not affect the electrical insulation of the appliance. Check by the following test
The outlet of the appliance is blocked and the container of the appliance is filled with water to a depth of 20 cm. The measurement is taken from the lowest point in the container. The appliance is powered by rated voltage and operates until the protective device operates or 15 min, whichever is shorter. After 15 min, the above test is repeated. Then, the appliance is subjected to the electrical strength test according to 16.3 and checked for possible reduction of creepage distances and electrical clearances to less than the specified values ​​of 29.1. There shall be no traces of water on the insulating surface. 16 Leakage current and electrical strength
This chapter in GB4706.1-1998 applies. 17 Over-regulation protection of transformers and related circuits This chapter in GB 4706. 1-1998 applies. 18 Durability
This chapter in GB4706.1-1998 does not apply. 19 Abnormal operation
This chapter in GB4706.1-1998 is applicable except for the following contents. 19.7 Added:
Appliance without water operation:
Continuous charging type, work for 30s;
Intermediate peptide charging type, work for 5min.
19.9 Not applicable.
20 Stability and mechanical hazards
This chapter in GB4706.1-1998 is applicable except for the following contents. 20.2 Added:
The test finger is not applicable to the inlet of the appliance.
20.101 The appliance shall be able to prevent contact with moving parts through the open inlet. Unless a cover is installed and the motor automatically shuts down when the cover is removed.
GB 4706.49—2000
Use the gauge shown in Figure 101 to apply a force of 50N to the open inlet for inspection. The gauge cannot touch the moving parts. In addition, the distance between the top of the inlet and the moving parts should not be less than 100mm. Adjust the appliance so that the base bottom is the thinnest.
2 Removable parts should prevent waste food from being ejected or blood from falling into the moving crushing cavity. 21 Mechanical strength
This chapter in GB4706.1—1998 is applicable. 22 Structure
This chapter in GB4706.1—1998 is applicable except for the following contents. 22.101 The appliance should be equipped with a protective device, and its compliance should be checked by regulatory inspection.
22.102 The reset button of the protective device should be placed in a concealed place or protected by other means. A test specimen is brought into contact with the closed guard from any direction. The diameter of the test rod is (76 ± 0.1) mm and the end is chamfered:
The distance from the test rod to the button shall not be less than 1.5 mm. The guard shall be prevented from being actuated by the test rod and shall not be able to reset automatically. 22.103 The construction of the appliance shall ensure that waste food cannot be ejected through the open inlet and that the guard and material chamber can be cleaned. In the other tests, it shall be checked by visual inspection. NOTE: Water condensation from the open water inlet with a height of less than 15 crm may be ignored. 22.104 The surface material of the grinding chamber shall be able to withstand mechanical damage and the impact of waste food. It shall be checked by the following test.
A mild steel bar of approximately 100 mm × 12 mm × 3 mm is inserted into the grinding chamber and is arranged to reduce the possibility of motor stalling.
The appliance is supplied with rated voltage and operated for 15 s unless the motor stalls initially. After the test, the appliance shall comply with the requirements of 8.1.15.2, 16.3 and 29.1. NOTES
1 A test to verify resistance to corrosion by discarded food may be necessary. 2 Natural rubber is considered to be susceptible to corrosion by discarded food. 23 Internal wiring
This clause of GB 4706.1-1998 applies. 24 Components
This clause of GB 4706.1-1998 applies except as follows 24.101 Thermal cut-outs and protective devices for use with continuously charged appliances shall be non-resettable. Verified by regulatory inspection and test of clause 19. 25 Supply connection and external flexible cord
This clause of GB 4706.1-1998 applies: 26 Terminals for external conductors
This clause of GB 4706.1-1998 applies.
27 Grounding measures
This clause in GB4706.1-1998 is applicable.
28 Screws and connections
This clause in GB4706.1-1998 is applicable. 29 Creepage distances, clearances and through insulation distances This clause in GB4706.1-1998 is applicable. 30 Heat resistance, flame resistance and leakage current resistance
GB 4706. 49-2000
This clause in GB4706.1-1998 is applicable except for the following contents. 30.2 Added:
30.2.3 This clause is not applicable.
31 Rust prevention
This clause in GB4706.1-1998 is applicable. 32 Radiation, toxicity and similar hazards
This chapter in GB 4706.1-1998 is applicable. 10±0.2
Figure 101 Test specification
?0千08
Dimension unit: mm
GB 4706.49--2000
The appendices in GB 4706.1-1998 are applicable except for the following contents. Appendix C
(Standard Appendix)
Aging test for motors
Addition: Force value equal to 2000,2 Replacement:
The structure of the appliance shall ensure that the blockage of its outlet does not affect the electrical insulation of the appliance. Check by the following test
The outlet of the appliance is blocked and the container of the appliance is filled with water to a depth of 20 cm. The measurement is taken from the lowest point in the container. The appliance is powered by rated voltage and operates until the protective device operates or 15 min, whichever is shorter. After 15 min, the above test is repeated. Then, the appliance is subjected to the electrical strength test according to 16.3 and checked for possible reduction of creepage distances and electrical clearances to less than the specified values ​​of 29.1. There shall be no traces of water on the insulating surface. 16 Leakage current and electrical strength
This chapter in GB4706.1-1998 applies. 17 Over-regulation protection of transformers and related circuits This chapter in GB 4706. 1-1998 applies. 18 Durability
This chapter in GB4706.1-1998 does not apply. 19 Abnormal operation
This chapter in GB4706.1-1998 is applicable except for the following contents. 19.7 Added:
Appliance without water operation:
Continuous charging type, work for 30s;
Intermediate peptide charging type, work for 5min.
19.9 Not applicable.
20 Stability and mechanical hazards
This chapter in GB4706.1-1998 is applicable except for the following contents. 20.2 Added:
The test finger is not applicable to the inlet of the appliance.
20.101 The appliance shall be able to prevent contact with moving parts through the open inlet. Unless a cover is installed and the motor automatically shuts down when the cover is removed.
GB 4706.49—2000
Use the gauge shown in Figure 101 to apply a force of 50N to the open inlet for inspection. The gauge cannot touch the moving parts. In addition, the distance between the top of the inlet and the moving parts should not be less than 100mm. Adjust the appliance so that the base bottom is the thinnest.
2 Removable parts should prevent waste food from being ejected or blood from falling into the moving crushing cavity. 21 Mechanical strength
This chapter in GB4706.1—1998 is applicable. 22 Structure
This chapter in GB4706.1—1998 is applicable except for the following contents. 22.101 The appliance should be equipped with a protective device, and its compliance should be checked by regulatory inspection.
22.102 The reset button of the protective device should be placed in a concealed place or protected by other means. A test specimen is used to contact the closed guard from any direction. The diameter of the test rod is (76 ± 0.1) mm and the end is chamfered:
The distance from the test rod to the button shall not be less than 1.5 mm. The guard shall be prevented from being activated by the test rod and shall not be able to reset automatically. 22.103 The construction of the appliance shall ensure that waste food cannot be ejected through the open inlet and that the guard and material chamber can be cleaned. In other tests, it is checked by visual inspection. NOTE: Water splashing from the open water inlet to a height of less than 15 crm can be ignored. 22.104 The surface material of the grinding chamber shall be able to withstand mechanical damage and the impact of waste food. It is checked by the following test.
A mild steel bar of approximately 100 mm × 12 mm × 3 mm is inserted into the grinding chamber and is inserted so that the possibility of motor stalling is reduced.
The appliance is supplied with rated voltage and operated for 15 s unless the motor initially stalls. After the test, the appliance shall comply with the requirements of 8.1.15.2, 16.3 and 29.1. NOTES
1 A test to verify resistance to corrosion by discarded food may be necessary. 2 Natural rubber is considered to be susceptible to corrosion by discarded food. 23 Internal wiring wwW.bzxz.Net
This clause of GB 4706.1-1998 applies. 24 Components
This clause of GB 4706.1-1998 applies except as follows 24.101 Thermal cut-outs and protective devices for use with continuously charged appliances shall be non-resettable. Verified by regulatory inspection and test of clause 19. 25 Supply connection and external flexible cord
This clause of GB 4706.1-1998 applies: 26 Terminals for external conductors
This clause of GB 4706.1-1998 applies.
27 Grounding measures
This clause in GB4706.1-1998 is applicable.
28 Screws and connections
This clause in GB4706.1-1998 is applicable. 29 Creepage distances, clearances and through insulation distances This clause in GB4706.1-1998 is applicable. 30 Heat resistance, flame resistance and leakage current resistance
GB 4706. 49-2000
This clause in GB4706.1-1998 is applicable except for the following contents. 30.2 Added:
30.2.3 This clause is not applicable.
31 Rust prevention
This clause in GB4706.1-1998 is applicable. 32 Radiation, toxicity and similar hazards
This chapter in GB 4706.1-1998 is applicable. 10±0.2
Figure 101 Test specification
?0千08
Dimension unit: mm
GB 4706.49--2000
The appendices in GB 4706.1-1998 are applicable except for the following contents. Appendix C
(Standard Appendix)
Aging test for motors
Addition: Force value equal to 2000,And, so that it is arranged to reduce the possibility of the motor stalling.
The appliance is supplied with rated voltage and operated for 15 s unless the motor stalls initially. After the test, the appliance shall comply with the requirements of 8.1.15.2, 16.3 and 29.1. NOTE
1 A test to verify resistance to corrosion by waste food may be necessary. 2 Natural rubber is considered to be susceptible to corrosion by waste food. 23 Internal wiring
This clause of GB 4706.1-1998 applies. 24 Components
This clause of GB 4706. 1-1998 applies except as follows 24.101 Thermal cut-outs and protective devices used with continuously charged appliances shall be non-resettable. Pass the regulatory inspection and the test of clause 19. 25 Power supply connection and external flexible cord
This chapter in GB4706.1-1998 is applicable: 26 Terminals for external conductors
This chapter in GB4706.1-1998 is applicable.
27 Grounding measures
This chapter in GB4706.1-1998 is applicable.
28 Screws and connections
This chapter in GB4706.1-1998 is applicable. 29 Creepage distances, electrical clearances and through insulation distances
This chapter in GB4706.1-1998 is applicable. 30 Heat resistance, flame resistance and creepage resistance
GB 4706. 49-2000
This chapter in GB4706.1-1998 is applicable except for the following contents. 30.2 Added:
30.2.3 This clause is not applicable.
31 Rust prevention
This chapter in GB4706.1-1998 is applicable. 32 Radiation, toxicity and similar hazards
This chapter in GB 4706.1-1998 is applicable. 10±0.2
Figure 101 Test specification
?0千08
Dimension unit; mm
GB 4706.49--2000
Except for the following contents, the appendices in GB 4706.1-1998 are applicable. Appendix C
(Standard Appendix)
Aging test for electric motors
Added: Force value equal to 2000,And, so that it is arranged to reduce the possibility of the motor stalling.
The appliance is supplied with rated voltage and operated for 15 s unless the motor stalls initially. After the test, the appliance shall comply with the requirements of 8.1.15.2, 16.3 and 29.1. NOTE
1 A test to verify resistance to corrosion by waste food may be necessary. 2 Natural rubber is considered to be susceptible to corrosion by waste food. 23 Internal wiring
This clause of GB 4706.1-1998 applies. 24 Components
This clause of GB 4706. 1-1998 applies except as follows 24.101 Thermal cut-outs and protective devices used with continuously charged appliances shall be non-resettable. Pass the regulatory inspection and the test of clause 19. 25 Power supply connection and external flexible cord
This chapter in GB4706.1-1998 is applicable: 26 Terminals for external conductors
This chapter in GB4706.1-1998 is applicable.
27 Grounding measures
This chapter in GB4706.1-1998 is applicable.
28 Screws and connections
This chapter in GB4706.1-1998 is applicable. 29 Creepage distances, electrical clearances and through insulation distances
This chapter in GB4706.1-1998 is applicable. 30 Heat resistance, flame resistance and creepage resistance
GB 4706. 49-2000
This chapter in GB4706.1-1998 is applicable except for the following contents. 30.2 Added:
30.2.3 This clause is not applicable.
31 Rust prevention
This chapter in GB4706.1-1998 is applicable. 32 Radiation, toxicity and similar hazards
This chapter in GB 4706.1-1998 is applicable. 10±0.2
Figure 101 Test specification
?0千08
Dimension unit; mm
GB 4706.49--2000
Except for the following contents, the appendices in GB 4706.1-1998 are applicable. Appendix C
(Standard Appendix)
Aging test for electric motors
Added: Force value equal to 2000,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.