This regulation applies to the design of steel shells of carbon steel welded anti-corrosion lining (or coating) equipment with a design pressure greater than -0.02MPa and less than 0.6MPa, and a design temperature greater than -20℃ and less than or equal to 200℃. HG/T 20678-2000 Technical Regulations for Lined Steel Shell Design HG/T20678-2000 Standard Download Decompression Password: www.bzxz.net

Industry Standard of the People's Republic of China
HG/T 20678 - 2000
Technical Specification on Design of Steel Shell with Liner
Specification on Design of Steel Shell with Liner2000 - 11 - 14
2001 - 06 - 01
State Administration of Petroleum and Chemical Industry
Document of State Administration of Petroleum and Chemical Industry
State Petrochemical Administration (2000) No. 423
Notice on Approval of 7 Chemical Industry Standards Including "Regulations on the Preparation of Chemical Equipment Design Documents"
China Chemical Exploration and Design Association:
According to the project plan for the formulation and revision of engineering construction industry standards of our bureau, the draft of 7 chemical industry standards including "Regulations on the Preparation of Chemical Equipment Design Documents" organized and completed by your unit have been approved by our bureau and are now published. The name and number of the standard are: Recommended standard:
Standard number
HG/T 20668 - 2000
HG/T 20678 - 2000
HG/T 20701 - 2000wwW.bzxz.Net
HG/T 20702 - 2000
HG/T 20703 - 2000
HG/T 20704 - 2000
Standard name
Regulations on the preparation of design documents for chemical equipment
Technical regulations for the design of lined steel shells
Professional engineering design management of containers and heat exchangers
Regulations on the professional engineering design management of special equipment
Regulations on the professional engineering design management of materials
Regulations on the professional engineering design management of pumps
Mandatory standard
Standard number
HG 20660 - 2000
Standard name
Classification of toxic hazards of chemical media in pressure vessels
and explosion hazard degree
The above standards shall be implemented from June 1, 2001. State Administration of Petroleum and Chemical Industry
November 14, 2000
China Chemical Exploration and Design Association
China Chemical Exploration and Design Association [20001181]
Notice on Editing and Issuing 7 Chemical Industry Standards including "Regulations on the Preparation of Chemical Equipment Design Documents"
National Chemical Engineering Construction Standard Editing Center: According to the notice of the document No. 423 of the State Petrochemical Administration (2000), the State Administration of Petroleum and Chemical Industry has approved 7 chemical industry standards including "Regulations on the Preparation of Chemical Equipment Design Documents". Based on this, our association entrusts your center to edit and issue the above standards. The name and number of the standard can be found in Document No. 423.
China Chemical Engineering Survey and Design Association
October 15, 2000
Industry Standard of the People's Republic of China
Specification on Design of Steel Shell with Liner
Specification on Design of Steel Shell with LinerHG/T 20678 -2000
Editor: Huatai Engineering Company, Second Design Institute of Chemical Industry
Approval Department: State Administration of Petroleum and Chemical Industry Implementation Date: June 1, 2000
National Chemical Engineering Construction Standard Editing Center (formerly Engineering Construction Standard Editing Center of Ministry of Chemical Industry) Beijing
According to the arrangement of the Equipment Design Technology Center of Ministry of Chemical Industry, Second Design Institute of Chemical Industry (formerly Second Design Institute of Ministry of Chemical Industry) revised the original "Technical Specifications on Design of Steel Shell with Liner" (HGJ33-91).
This revision is based on the original "Technical Specifications on Design of Steel Shell with Liner" (HGJ33-91) and is supplemented and revised based on many years of implementation experience. The main purpose of this revision is to supplement the original regulations for the lack of provisions on the design of the pressure-lined steel shell and the shortcomings in the structural design, and to delete some unnecessary parts. This makes this regulation more complete and more practical than the original.
The main drafter of this revision is Yuan Bin from the Equipment Department of the Second Design Institute of Chemical Industry (formerly the Second Design Institute of the Ministry of Chemical Industry). Chen Youzi, Lu Hongwei, and Gong Wanchun participated in the work. The Second Design Institute of Chemical Industry
(Formerly the Second Design Institute of the Ministry of Chemical Industry)
June 2000
1 General
1.1 Scope of application
1.2 Applicable standards
2 Design of lined steel shell
2.1 Determination of the wall thickness of the lined steel shell.
2.2 Determination of other pressure-bearing parts.
2.3 Structural design of lined steel shell
Table of contents
3 Manufacture, test, inspection, acceptance and storage of lined steel shell3.1 Requirements for manufacture, test, inspection and acceptance3.2 Surface treatment and protection, storage
Appendix A
Reference method for surface inspection of steel shell lining
Preparation instructions
(3)
.(5)
·(12)
..(12)
(16)
1 General
1.1 Scope of application
1.1.1 This regulation applies to the design of steel shell of equipment with anti-corrosion lining (or coating) made of carbon steel welded with a design pressure greater than -0.02MPa and less than or equal to 0.6MPa and a design temperature greater than -20℃ and less than or equal to 200℃.
1.1.2 Lining materials include anti-corrosion coatings, acid-resistant porcelain (ceramic) plates and tiles, cast stone plates, carbon bricks, impermeable graphite plates, soft polyvinyl chloride plates, fiberglass, rubber plates and lead. 1. 1.3
These regulations do not apply to the following lining equipment: lining equipment directly heated by flame;
lining equipment that is frequently moved, rotated or vibrated; lining equipment affected by auxiliary radiation;
glass equipment;
metal lining equipment other than village (pond) lead and shrink-fit lining equipment. 1.2 Reference standards
In addition to implementing the requirements of this regulation, the design and manufacture of lined steel shells shall also comply with the requirements of the following standards, specifications and regulations (latest edition): State Administration of Quality and Technical Supervision
HG20580
HG 20581
HG 20582
HG20583
HG20584
《Regulations on Safety Technical Supervision of Pressure Vessels》99 Edition)《Steel Pressure Vessels》
《Basic Regulations for Design of Steel Chemical Vessels》《Regulations for Material Selection of Steel Chemical Vessels》《Regulations for Strength Calculation of Steel Chemical Vessels》《Regulations for Structural Design of Steel Chemical Vessels》《Technical Regulations for Manufacturing of Steel Chemical Vessels》JB4710
JB/T4735
GB 8923
GB 6654
JB4708
JB/T4709
HG2151421535
HG 21588 ~21592
HG/T 21622
ZBG 91003
JB 4701 ~ 4703
HGJ 202
HG20592 -20635
《Steel tower container》
《Steel horizontal container》
《Steel welded normal pressure container》
《Surface rust grade and rust removal grade of steel before painting》
《Carbon steel and low alloy steel thick steel plates for pressure vessels》
《Welding process assessment for steel pressure vessels》《Welding regulations for steel pressure vessels》
《Manholes and handholes for carbon steel and low alloy steel》《Glass plate liquid level gauge, glass tube liquid level gauge》《Village sight glass》||t t||"Carbon Steel Lined F46 Glass Float Liquid Level Gauge"
"Pressure Vessel Flange"
"Degreasing Engineering Construction and Acceptance Specifications"
"Steel Pipe Flanges, Gaskets, Fasteners" Technical Conditions for Non-metallic Lining (Brick Plate, Rubber, Soft Polyvinyl Chloride, FRP, etc.) Equipment and Technical Conditions for Pond and Lead Lining Equipment
Design of Lined Steel Shell
Determination of Lined Steel Shell Wall Thickness
The minimum wall thickness of the lined steel shell shall not be less than 5mm (Di≤4000mm). From the perspective of rigidity, the minimum wall thickness of the lining steel shell is: 2D;
wherein ~
-minimum wall thickness of the lining steel shell, mm;
D: inner diameter of the lining steel shell, mm;
C wall thickness addition, mm; This regulation takes into account the negative deviation of steel plate thickness, the wall thickness reduction caused by surface rust removal, and the corrosion of the steel shell by the imperfection of some lining (coating) layers or their own acidity except for lead lining, rubber lining, plastic lining, etc., and takes C=2mm;
-rigidity addition, mm, see Table 2.1.2
Table 2.1.2 Rigidity addition A for lining steel shell wall thickness Inner diameter of steel shell Di, mm
Rigidity addition A, mm
Di 600
Note: 8 shall not be less than 5mm
600
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.