Some standard content:
UDC661.73:664
National Standard of the People's Republic of China
GB 8849 .-- 88
Alarm: G 2f24 -1988
Food additives
1988-02-25 Issued
Additives
Ethoxyquin
1988-1101 Implementation
National Bureau of Standards Issued
National Standard of the People's Republic of China
Additives
Food additives
Ethoxyquin
FaHl additjve
Ethoxyquin
UDC 661.73
GB 88 4 9
This standard applies to ethoxyquin which is synthesized by using p-aminoethyl ether and acetone as raw materials under the conditions of catalyst and heating reaction. This product is used as an antioxidant, mainly to prevent and treat the tiger skin disease that occurs during the apple season. Molecular formula: C,H.NO
Structural formula:
Quantity: 217.31 (according to the 1985 International Atomic Quantity Scale) 1 Technical conditions
1.1 Appearance
Pale yellow to amber viscous liquid (after being placed in light and air for a long time, it gradually turns into a dark brown liquid, but it does not affect the use effect). 1.2 Ethoxyquin should meet the following index requirements: Index name
Ethoxyquin, in addition
(AS), Luo
Heavy metals (Ph it),%
Para-nitroviolet phenethyl ether,%
Test method
Unless otherwise specified, the reagents used in the test are analytically pure; the water is distilled water; the instruments and equipment are general experimental instruments and equipment. 2.1 Identification
Dissolve 1m of ethoxyquin crude oil in 10ml of acetonitrile and observe under ultraviolet light, which can show strong fluorescence. 2.2 Determination of the content of ethoxyquin crude oil
2.2.1 Reagents and solutions
Approved by the Ministry of Chemical Industry of the People's Republic of China on February 4, 1988 and implemented on November 1, 1988
2.2.1.1 Glacial acetic acid (GB 678·78),
GB 8849-88
2.2.1.2J% methyl violet solution: weigh 1g of methyl violet and dissolve it in 100ml of glacial acetic acid. 2.2.1.3 Perchloric acid (GB623-77) standard solution: c(HC10.) = 0.1mo)/L (i.e. 0.1N), prepared and calibrated according to GB601---77:
2.2,1.4 Acetic anhydride (GP 67778);
2.2.1.5 Ortho-potassium hydrogen formate (GB1291-77) high-grade purity. 2. 2.2 Steps
Weigh about 0.28 g of ethoxyquin crude oil sample (accurate to 0.0002 g) into a 200 ml flask, add 80 ml of glacial acetic acid (2.2.1.1), mix well, add 2 drops of 1% methyl violet indicator (2.2.1.2), and titrate with perfluoric acid standard solution (2.2.1.3) until it turns blue-green, which is the end point. Record the number of ml of standard solution consumed. 2.2.3 Calculation
Ethoxyquin white content (X,) is calculated according to formula (1): X.-FX0.2173 ×100
Where
Concentration of perchloric acid standard solution, mol/L, volume of perchloric acid standard solution consumed, m!; Mass of ethoxyquin crude oil, g;
1 ml c(HcIO,)-0. 1 mol/mol high murine acid standard solution is equivalent to the mass of ZnO2O3. The relative deviation allowed by this method is not more than 0.4%. 2.3 Determination of arsenic and heavy metals (in terms of Pb) 2.3.1 Sample treatment
2.3.1.1 Reagents
2.3.1.1 Nitric acid (GB 626
2.3.1.1.2 Sulfuric acid (GB62577),
2.3.1.2 Operation method
Weigh 5g of ethoxylated crude oil sample (accurate to 0.001g) in a 250ml Kjeldahl flask or a 3-corner flask, add 1ml of nitric acid to soak the sample, place it for a while, slowly heat it, wait for the effect to ease, cool it, add 5ml of sulfuric acid (2.3.1.1.2) along the wall of the flask, and slowly heat it again until the solution in the flask begins to turn brown. Continuously add nitric acid until the organic matter is completely decomposed, add fire, and a large amount of white sulfur dioxide smoke is generated. The final solution should be colorless or yellowish. After cooling, transfer the solution to a 50ml volumetric flask, wash the 3-corner flask with a little water 2~3 times, add the washing solution to the volume, add water to the scale, mix well, and collect 10ml of this solution equivalent to 1g of sample. Take the same amount of nitric acid and sulfuric acid to make a reagent blank test according to the above method. 2.3.2 Determination of arsenic radicals Arsenic spot method 2.3.2.1 Principle In the presence of iodide and stannous chloride, the arsenic in the sample is reduced to trivalent arsenic. Trivalent arsenic reacts with nascent ammonia to generate hydrogen sulfide gas, which is then filtered through lead acetate cotton to remove hydrogen sulfide interference. The gas then reacts with mercuric bromide test paper to generate a yellow to orange spot, which is compared with the standard arsenic spot for a limit test.
2.3.2.2 Reagents
2.3.2.2.1 Hydrochloric acid (GB62277)
2.3.2.2.2 Potassium iodide (GB1272:77): 15% solution; 2.3.2.2.3 Stannous chloride (GB638
78): 40% hydrochloric acid solution; Www.bzxZ.net
2.3.2.2.4 Lead acetate cotton: prepared according to GB603-77 "Chemical Reagent Preparation and Product Preparation Method"; 2.3.2.2.5 Bullet standard solution: (1ml contains 0.001mgAs), prepared according to GB60277 "Chemical Reagent Impurity Standard Solution Preparation Method" and then diluted 100 times t
2.3.2.2.6 Mercury bromide test paper: prepared according to GB60377. 2
2.3.2.3 Instrument
GB 884988
According to the "Salt Test Method\Instrumentation Device" of the 1985 edition of the Chinese Pharmacopoeia. 2.3.2.4 Determination
Put 10ml of the sample nitration solution of 2.3.1, 3ml of the same amount of reagent blank solution and arsenic standard solution (2.3.2.2.5) in test bottles respectively, add 5ml of hydrochloric acid. Then add water to 35ml, 5ml of 15% potassium iodide solution, 5 drops of 40% stannous chloride, and let it stand at room temperature for 10min. Add 1g of zinc particles to the test bottles of the sample nitration solution, reagent blank solution and arsenic limit standard solution, and immediately plug the test tubes pre-filled with lead acetate cotton and bromide test paper, let it stand at 25℃ for 1h, take out the stain for comparison, and the stain of the sample shall not be deeper than the arsenic stain of the arsenic limit standard.
2.3.3 Determination of heavy metals (in terms of Pb)
2.3.3. Principle
Under weakly acidic conditions, the heavy metals in the sample react with nitrogen sulfide to produce brown-black color, and the limit test is performed by daylight colorimetry. 2.3.3.2 Reagents
2.3.3.2.1 Hydrochloric acid (GB622-77): 1+1 hydrochloric acid solution, prepare 1+ hydrochloric acid solution according to GB603-77;
2.3.3.2.2 Cyanide water (G63-77): 2:30 ammonia water, 2.3.3.2.3 Ammonium acetate buffer: pH is 3.5, weigh 25.0g of ammonium acetate and dissolve it in 25ml of water, add 1+1 salt 45ml of acid, adjust pH to 3.5 with 1+11 hydrochloric acid or 2:30 nitrogen water. Dilute with water to 1000ml; 2.3.3.2.4 1% phenol indicator: prepared according to GB603-7; 2.3.3.2.5 Saturated hydrogen sulfide water: prepared according to GB603-77; 2.3.3.2.6 Lead standard solution (1ml contains 0.01m Pb). Prepare according to GB602-77 and dilute 10 times. 2.3.3.3 Instruments
2.3.3.3.1 Hydrogen generator.
2.3.3.3.2 50ml Nessler colorimetric tube.
2.3.3.4 Determination
2.3.3.4.1 Solution A: Pipette 1 ml of lead standard solution (2.3.3.2.6) into a 50 ml Nassler colorimetric tube, add 25 ml of water and mix well, add 1 drop of 1% phenolic acid indicator, adjust pH to neutral (phenolic acid red just fades) with 1+11 hydrochloric acid or 2:30 ammonia water, add 5 ml of pH3.5 acetate buffer, dilute with water to 40 ml. Fill well and set aside. 2.3.3. 4. 2 Solution B: Pipette 11 ml of sample nitration solution of 2.3.1 into another Nessler colorimetric tube matching solution A, add 25 ml of water and mix well, add 1 drop of 1% phenolic acid indicator, adjust pH to neutral (phenolic acid red just fades) with 1+11 hydrochloric acid or 2:30 rehydration. Add pH3.2.3.3.4.3 Solution C: Pipette 10ml of the sample nitration solution in 2.3.1 into the Nessler colorimetric tubes matching solutions A and B, add 1ml of lead standard solution, add water to 25ml, mix well, add 1% phenolic acid indicator, adjust the pH to neutral (the red color of phenolic acid just fades) with 1+11 hydrochloric acid or 2:30 hydrogen water, add 5ml of pH3.5 acetate buffer, dilute with water to 40ml, mix well and set aside. 2.3.3.4.4 Visual colorimetry: Add 10ml of freshly prepared saturated hydrogen peroxide solution to each tube, mix well, leave for 10 minutes and observe under the self-color background. The chromaticity of solution B shall not be darker than that of solution A. The chromaticity of solution C shall be equivalent to that of solution A or darker than that of the free solution.
2.4 Determination of amino ether content
2.4.1 Instrument
2.4.1.1 Gas chromatograph: with hydrogen flame ionization detector; 2.4.1.2 Glass chromatographic column: coiled, 1m long, 2mm inner diameter, coated with 1.5% ov-17/shimaliteWAW (80～J00 mesh);
2.4.1.3 Micro syringe: 10ul.
2.4.2 Reagents and solutions
2.4.2. 1 Anhydrous Z alcohol (GB 67878);
CB8849
2.4.2.2 Diethyl phthalate internal standard solution: chemically pure, weigh diethyl phthalate 1 (accurate to 0.001g) in 100ml In a volumetric flask, use anhydrous ethanol as solvent and dilute to the scale for later use; 2.4.2.3 p-Aminophenyl ether standard solution: weigh 0.05g (accurate to 1.0002g) of p-nitrophenylacetaldehyde (purity ≥ 99%) into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution of monoethyl phthalate (2.4.2.2) into this vial, cover the vial, shake well and set aside;
2.4.2.4 Sample solution: weigh 0.3mg (accurate to 0.0002B) of ethoxybenzoic acid crude oil into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution (2.1.2.2) into this vial, cover the vial, shake well and set aside. 2.4.3 Determination steps
2.4.3.1 Gas chromatography operating conditions
Temperature: Column temperature 160℃, gasification.190r: Detection 190℃: Gas flow rate: Carrier gas high purity nitrogen (99.99%) 25 ml/min; Hydrogen 30 ml/min: Air 500 ml/min. Note: The analyst can make appropriate adjustments to the above operating conditions according to the characteristics of the instrument to obtain the best effect. 2.4.3.2 Determination
Under the gas chromatography operating conditions of 2.4.3.1, after the instrument is stable, add several needles of standard drop solution until the peak-to-product ratio of two adjacent needles is basically stable. Analyze in the following order: B standard solution (2, 4.2.3):
b mixed solution (2.4.2.4):
c. Sample solution (2.1.2.4) 1
d. Standard solution (2.4.2.3).
The injection volume is 1μl.
2.4.3.3 Calculation
Average the obtained peak area ratios of a, d and b, c. The peak area ratio of each injection is calculated according to formula (2): S
Wherein, S. Peak area of p-aminophenyl ethyl ether; S
Peak area of internal standard.
The percentage of p-aminophenylacetaldehyde ether (X,) is calculated according to formula (3): X+-r,.m,p
-The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the standard solution;: The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the sample solution; -The mass of p-aminophenyl ether standard, B, The mass of ethoxyquin crude oil, B;
-The percentage of p-aminophenylacetaldehyde standard. The relative deviation allowed by this method is not more than 6%. 3 Acceptance rules
3.1 The technical inspection department of the manufacturer shall be responsible for the inspection and acceptance of this product. The manufacturer shall ensure that all products shipped meet the requirements of this standard and attach a product certificate in the packaging. 3.2 The user can verify whether the product quality meets the requirements of this standard in accordance with the provisions of this standard. 3.3 The acetoxyquin crude oil shall be a batch not exceeding the capacity of a single production batch or packaging storage tank. 3.4 Sampling method: 30% of the total number of barrels delivered in each batch shall be selected for sampling. For small batches, no less than 5 barrels shall be selected. 8849
The samples should be collected from the upper, middle and lower parts of the barrel. The total number of samples should not be less than 500ml. For 0.6kg bottled products, the product in each bottle should be shaken and sampled with a straw. The total number of samples should not be less than 200ml. The selected samples should be carefully mixed and divided into two clean and dry brown glass bottles with ground stoppers, and labeled with the manufacturer name, product batch number, product name, production date and sampling date. The first bottle shall be inspected by the inspection department, and the second bottle shall be sealed and stored for arbitration.
3.5 If any item of the inspection result does not meet the requirements of this standard, a new sample should be taken from the packaging with double the sampling amount for re-inspection. If there is still one item that fails to meet the requirements after the re-inspection, Then the batch of products cannot be accepted. 3.6\When the user unit raises an objection to the product quality and needs arbitration, the arbitration institution shall be selected by both parties through consultation. During the arbitration, the arbitration analysis shall be conducted in accordance with the inspection method specified in the standard.
4 Packaging, marking, storage and transportation
4.1 Ethoxyazole crude oil shall be packaged in clean and dry polyethylene plastic bags, with a net weight of 25kg per piece. Small packages shall be packaged in clean and dry brown glass bottles, with a net weight of 0.5kg per piece. 4.2 Each batch of products shall be accompanied by a quality certificate when leaving the factory. The certificate shall include the name of the manufacturer, production batch number, product name, date of manufacture, net weight, number of pieces, and proof that the product quality meets this standard. The words "food additives" shall be marked in a prominent position, and the packaging barrel or bottle shall be accompanied by instructions for use and storage conditions.
4.3 During transportation and storage, loading and unloading shall be light and efficient, and rain and sun shall be prevented. Vehicles and ships shall be clean, non-toxic and odorless. It is strictly forbidden to store them together with toxic items or other contaminated substances. When storing, it should be placed in a cool place and avoid direct sunlight. 4.4 The shelf life of this product is one year.
Additional Notes:
This standard is under the jurisdiction of Beijing Chemical Research Institute of the Ministry of Industry and Food Hygiene Supervision and Inspection Institute of the Ministry of Health. This standard was drafted by Shanghai Pesticide Research Institute and participated in by Shanghai Changzheng Second Chemical Plant. The main drafters of this standard are Ye Wenbing, Yao Junqing and Li Hougen. People's Republic of China
National Standard
GB 8849 .. 88
Published by China Standards Press
(Beijing Fuwai-Lihe)
National Standard Selection Press Beijing Printing! Printed
Xinhua Madian Beijing Publishing House Distributed by Xinhua Bookstores in all regions. Copyright reserved
Not allowed to print
80×12301/16 Printing sheet1/2
Word count 900
March 1989 edition
March 1989 First printing and deletion
Print run 1-3 000
Word book: 1550661-6066
Dongri 10
Starting price 0.40 yuan
8810e2
88-6±88901 Anhydrous Z alcohol (GB 67878);
CB8849
2.4.2.2 Diethyl phthalate internal standard solution: chemically pure, weigh diethyl phthalate 1 (accurate to 0.001g) in 100ml In a volumetric flask, use anhydrous ethanol as solvent and dilute to the scale for later use; 2.4.2.3 p-Aminophenyl ether standard solution: weigh 0.05g (accurate to 1.0002g) of p-nitrophenylacetaldehyde (purity ≥ 99%) into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution of monoethyl phthalate (2.4.2.2) into this vial, cover the vial, shake well and set aside;
2.4.2.4 Sample solution: weigh 0.3mg (accurate to 0.0002B) of ethoxybenzoic acid crude oil into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution (2.1.2.2) into this vial, cover the vial, shake well and set aside. 2.4.3 Determination steps
2.4.3.1 Gas chromatography operating conditions
Temperature: Column temperature 160℃, gasification.190r: Detection 190℃: Gas flow rate: Carrier gas high purity nitrogen (99.99%) 25 ml/min; Hydrogen 30 ml/min: Air 500 ml/min. Note: The analyst can make appropriate adjustments to the above operating conditions according to the characteristics of the instrument to obtain the best effect. 2.4.3.2 Determination
Under the gas chromatography operating conditions of 2.4.3.1, after the instrument is stable, add several needles of standard drop solution until the peak-to-product ratio of two adjacent needles is basically stable. Analyze in the following order: B standard solution (2, 4.2.3):
b mixed solution (2.4.2.4):
c. Sample solution (2.1.2.4) 1
d. Standard solution (2.4.2.3).
The injection volume is 1μl.
2.4.3.3 Calculation
Average the obtained peak area ratios of a, d and b, c. The peak area ratio of each injection is calculated according to formula (2): S
Wherein, S. Peak area of p-aminophenyl ethyl ether; S
Peak area of internal standard.
The percentage of p-aminophenylacetaldehyde ether (X,) is calculated according to formula (3): X+-r,.m,p
-The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the standard solution;: The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the sample solution; -The mass of p-aminophenyl ether standard, B, The mass of ethoxyquin crude oil, B;
-The percentage of p-aminophenylacetaldehyde standard. The relative deviation allowed by this method is not more than 6%. 3 Acceptance rules
3.1 The technical inspection department of the manufacturer shall be responsible for the inspection and acceptance of this product. The manufacturer shall ensure that all products shipped meet the requirements of this standard and attach a product certificate in the packaging. 3.2 The user can verify whether the product quality meets the requirements of this standard in accordance with the provisions of this standard. 3.3 The acetoxyquin crude oil shall be a batch that does not exceed the capacity of a single production batch or packaging storage tank. 3.4 Sampling method: 30% of the total number of barrels delivered in each batch shall be selected for sampling. For small batches, no less than 5 barrels shall be selected. 8849
The samples should be collected from the upper, middle and lower parts of the barrel. The total number of samples should not be less than 500ml. For 0.6kg bottled products, the product in each bottle should be shaken and sampled with a straw. The total number of samples should not be less than 200ml. The selected samples should be carefully mixed and divided into two clean and dry brown glass bottles with ground stoppers, and labeled with the manufacturer name, product batch number, product name, production date and sampling date. The first bottle shall be inspected by the inspection department, and the second bottle shall be sealed and stored for arbitration.
3.5 If any item of the inspection result does not meet the requirements of this standard, a new sample should be taken from the packaging with double the sampling amount for re-inspection. If there is still one item that fails to meet the requirements after the re-inspection, Then the batch of products cannot be accepted. 3.6\When the user unit raises an objection to the product quality and needs arbitration, the arbitration institution shall be selected by both parties through consultation. During the arbitration, the arbitration analysis shall be conducted in accordance with the inspection method specified in the standard.
4 Packaging, marking, storage and transportation
4.1 Ethoxyazole crude oil shall be packaged in clean and dry polyethylene plastic bags, with a net weight of 25kg per piece. Small packages shall be packaged in clean and dry brown glass bottles, with a net weight of 0.5kg per piece. 4.2 Each batch of products shall be accompanied by a quality certificate when leaving the factory. The certificate shall include the name of the manufacturer, production batch number, product name, date of manufacture, net weight, number of pieces, and proof that the product quality meets this standard. The words "food additives" shall be marked in a prominent position, and the packaging barrel or bottle shall be accompanied by instructions for use and storage conditions.
4.3 During transportation and storage, loading and unloading shall be light and efficient, and rain and sun shall be prevented. Vehicles and ships shall be clean, non-toxic and odorless. It is strictly forbidden to store them together with toxic items or other contaminated substances. When storing, it should be placed in a cool place and avoid direct sunlight. 4.4 The shelf life of this product is one year.
Additional Notes:
This standard is under the jurisdiction of Beijing Chemical Research Institute of the Ministry of Industry and Food Hygiene Supervision and Inspection Institute of the Ministry of Health. This standard was drafted by Shanghai Pesticide Research Institute and participated in by Shanghai Changzheng Second Chemical Plant. The main drafters of this standard are Ye Wenbing, Yao Junqing and Li Hougen. People's Republic of China
National Standard
GB 8849 .. 88
Published by China Standards Press
(Beijing Fuwai-Lihe)
National Standard Selection Press Beijing Printing! Printed
Xinhua Madian Beijing Publishing House Distributed by Xinhua Bookstores in all regions. Copyright reserved
Not allowed to print
80×12301/16 Printing sheet1/2
Word count 900
March 1989 edition
March 1989 First printing and deletion
Print run 1-3 000
Word book: 1550661-6066
Dongri 10
Starting price 0.40 yuan
8810e2
88-6±88901 Anhydrous Z alcohol (GB 67878);
CB8849
2.4.2.2 Diethyl phthalate internal standard solution: chemically pure, weigh diethyl phthalate 1 (accurate to 0.001g) in 100ml In a volumetric flask, use anhydrous ethanol as solvent and dilute to the scale for later use; 2.4.2.3 p-Aminophenyl ether standard solution: weigh 0.05g (accurate to 1.0002g) of p-nitrophenylacetaldehyde (purity ≥ 99%) into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution of monoethyl phthalate (2.4.2.2) into this vial, cover the vial, shake well and set aside;
2.4.2.4 Sample solution: weigh 0.3mg (accurate to 0.0002B) of ethoxybenzoic acid crude oil into a stoppered glass vial, use a pipette to accurately transfer 5ml of the internal standard solution (2.1.2.2) into this vial, cover the vial, shake well and set aside. 2.4.3 Determination steps
2.4.3.1 Gas chromatography operating conditions
Temperature: Column temperature 160℃, gasification.190r: Detection 190℃: Gas flow rate: Carrier gas high purity nitrogen (99.99%) 25 ml/min; Hydrogen 30 ml/min: Air 500 ml/min. Note: The analyst can make appropriate adjustments to the above operating conditions according to the characteristics of the instrument to obtain the best effect. 2.4.3.2 Determination
Under the gas chromatography operating conditions of 2.4.3.1, after the instrument is stable, add several needles of standard drop solution until the peak-to-product ratio of two adjacent needles is basically stable. Analyze in the following order: B standard solution (2, 4.2.3):
b mixed solution (2.4.2.4):
c. Sample solution (2.1.2.4) 1
d. Standard solution (2.4.2.3).
The injection volume is 1μl.
2.4.3.3 Calculation
Average the obtained peak area ratios of a, d and b, c. The peak area ratio of each injection is calculated according to formula (2): S
Wherein, S. Peak area of p-aminophenyl ethyl ether; S
Peak area of internal standard.
The percentage of p-aminophenylacetaldehyde ether (X,) is calculated according to formula (3): X+-r,.m,p
-The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the standard solution;: The average value of the peak area ratio of p-aminophenyl ether to the internal standard in the sample solution; -The mass of p-aminophenyl ether standard, B, The mass of ethoxyquin crude oil, B;
-The percentage of p-aminophenylacetaldehyde standard. The relative deviation allowed by this method is not more than 6%. 3 Acceptance rules
3.1 The technical inspection department of the manufacturer shall be responsible for the inspection and acceptance of this product. The manufacturer shall ensure that all products shipped meet the requirements of this standard and attach a product certificate in the packaging. 3.2 The user can verify whether the product quality meets the requirements of this standard in accordance with the provisions of this standard. 3.3 The acetoxyquin crude oil shall be a batch not exceeding the capacity of a single production batch or packaging storage tank. 3.4 Sampling method: 30% of the total number of barrels delivered in each batch shall be selected for sampling. For small batches, no less than 5 barrels shall be selected. 8849
The samples should be collected from the upper, middle and lower parts of the barrel. The total number of samples should not be less than 500ml. For 0.6kg bottled products, the product in each bottle should be shaken and sampled with a straw. The total number of samples should not be less than 200ml. The selected samples should be carefully mixed and divided into two clean and dry brown glass bottles with ground stoppers, and labeled with the manufacturer name, product batch number, product name, production date and sampling date. The first bottle shall be inspected by the inspection department, and the second bottle shall be sealed and stored for arbitration.
3.5 If any item of the inspection result does not meet the requirements of this standard, a new sample should be taken from the packaging with double the sampling amount for re-inspection. If there is still one item that fails to meet the requirements after the re-inspection, Then the batch of products cannot be accepted. 3.6\When the user unit raises an objection to the product quality and needs arbitration, the arbitration institution shall be selected by both parties through consultation. During the arbitration, the arbitration analysis shall be conducted in accordance with the inspection method specified in the standard.
4 Packaging, marking, storage and transportation
4.1 Ethoxyazole crude oil shall be packaged in clean and dry polyethylene plastic bags, with a net weight of 25kg per piece. Small packages shall be packaged in clean and dry brown glass bottles, with a net weight of 0.5kg per piece. 4.2 Each batch of products shall be accompanied by a quality certificate when leaving the factory. The certificate shall include the name of the manufacturer, production batch number, product name, date of manufacture, net weight, number of pieces, and proof that the product quality meets this standard. The words "food additives" shall be marked in a prominent position, and the packaging barrel or bottle shall be accompanied by instructions for use and storage conditions.
4.3 During transportation and storage, loading and unloading shall be light and efficient, and rain and sun shall be prevented. Vehicles and ships shall be clean, non-toxic and odorless. It is strictly forbidden to store them together with toxic items or other contaminated substances. When storing, it should be placed in a cool place and avoid direct sunlight. 4.4 The shelf life of this product is one year.
Additional Notes:
This standard is under the jurisdiction of Beijing Chemical Research Institute of the Ministry of Industry and Food Hygiene Supervision and Inspection Institute of the Ministry of Health. This standard was drafted by Shanghai Pesticide Research Institute and participated in by Shanghai Changzheng Second Chemical Plant. The main drafters of this standard are Ye Wenbing, Yao Junqing and Li Hougen. People's Republic of China
National Standard
GB 8849 .. 88
Published by China Standards Press
(Beijing Fuwai-Lihe)
National Standard Selection Press Beijing Printing! Printed
Xinhua Madian Beijing Publishing House Distributed by Xinhua Bookstores in all regions. Copyright reserved
Not allowed to print
80×12301/16 Printing sheet1/2
Word count 900
March 1989 edition
March 1989 First printing and deletion
Print run 1-3 000
Word book: 1550661-6066
Dongri 10
Starting price 0.40 yuan
8810e2
88-6±88901. The technical inspection department of the manufacturer shall be responsible for the inspection and acceptance of this product. The manufacturer shall ensure that all products shipped out of the factory meet the requirements of this standard and attach a product certificate in the packaging. 3.2 The user may verify whether the product quality meets the requirements of this standard in accordance with the provisions of this standard. 3.3 The capacity of the acetyl cyanide crude oil shall not exceed the capacity of the production batch or the packaging storage tank. 3. 4 Sampling method;
30% of the total number of each batch delivered shall be selected for sampling, and the number of small batches shall not be less than 5 barrels. Use a 4
GB with a diameter of 13 mm and a length of 1 m at one end. 8849
The samples should be collected from the upper, middle and lower parts of the barrel. The total number of samples should not be less than 500ml. For 0.6kg bottled products, the product in each bottle should be shaken and sampled with a straw. The total number of samples should not be less than 200ml. The selected samples should be carefully mixed and divided into two clean and dry brown glass bottles with ground stoppers, and labeled with the manufacturer name, product batch number, product name, production date and sampling date. The first bottle shall be inspected by the inspection department, and the second bottle shall be sealed and stored for arbitration.
3.5 If any item of the inspection result does not meet the requirements of this standard, a new sample should be taken from the packaging with double the sampling amount for re-inspection. If there is still one item that fails to meet the requirements after the re-inspection, Then the batch of products cannot be accepted. 3.6\When the user unit raises an objection to the product quality and needs arbitration, the arbitration institution shall be selected by both parties through consultation. During the arbitration, the arbitration analysis shall be conducted in accordance with the inspection method specified in the standard.
4 Packaging, marking, storage and transportation
4.1 Ethoxyazole crude oil shall be packaged in clean and dry polyethylene plastic bags, with a net weight of 25kg per piece. Small packages shall be packaged in clean and dry brown glass bottles, with a net weight of 0.5kg per piece. 4.2 Each batch of products shall be accompanied by a quality certificate when leaving the factory. The certificate shall include the name of the manufacturer, production batch number, product name, date of manufacture, net weight, number of pieces, and proof that the product quality meets this standard. The words "food additives" shall be marked in a prominent position, and the packaging barrel or bottle shall be accompanied by instructions for use and storage conditions.
4.3 During transportation and storage, loading and unloading shall be light and efficient, and rain and sun shall be prevented. Vehicles and ships shall be clean, non-toxic and odorless. It is strictly forbidden to store them together with toxic items or other contaminated substances. When storing, it should be placed in a cool place and avoid direct sunlight. 4.4 The shelf life of this product is one year.
Additional Notes:
This standard is under the jurisdiction of Beijing Chemical Research Institute of the Ministry of Industry and Food Hygiene Supervision and Inspection Institute of the Ministry of Health. This standard was drafted by Shanghai Pesticide Research Institute and participated in by Shanghai Changzheng Second Chemical Plant. The main drafters of this standard are Ye Wenbing, Yao Junqing and Li Hougen. People's Republic of China
National Standard
GB 8849 .. 88
Published by China Standards Press
(Beijing Fuwai-Lihe)
National Standard Selection Press Beijing Printing! Printed
Xinhua Madian Beijing Publishing House Distributed by Xinhua Bookstores in all regions. Copyright reserved
Not allowed to print
80×12301/16 Printing sheet1/2
Word count 900
March 1989 edition
March 1989 First printing and deletion
Print run 1-3 000
Word book: 1550661-6066
Dongri 10
Starting price 0.40 yuan
8810e2
88-6±88901. The technical inspection department of the manufacturer shall be responsible for the inspection and acceptance of this product. The manufacturer shall ensure that all products shipped out of the factory meet the requirements of this standard and attach a product certificate in the packaging. 3.2 The user can verify whether the product quality meets the requirements of this standard in accordance with the provisions of this standard. 3.3 The capacity of the acetyl cyanide crude oil shall not exceed the capacity of the production batch or the packaging storage tank. 3. 4 Sampling method;
30% of the total number of each batch delivered shall be selected for sampling, and the number of small batches shall not be less than 5 barrels. Use a 4
GB with a diameter of 13 mm and a length of 1 m at one end. 8849
The samples should be collected from the upper, middle and lower parts of the barrel. The total number of samples should not be less than 500ml. For 0.6kg bottled products, the product in each bottle should be shaken and sampled with a straw. The total number of samples should not be less than 200ml. The selected samples should be carefully mixed and divided into two clean and dry brown glass bottles with ground stoppers, and labeled with the manufacturer name, product batch number, product name, production date and sampling date. The first bottle shall be inspected by the inspection department, and the second bottle shall be sealed and stored for arbitration.
3.5 If any item of the inspection result does not meet the requirements of this standard, a new sample should be taken from the packaging with double the sampling amount for re-inspection. If there is still one item that fails to meet the requirements after the re-inspection, Then the batch of products cannot be accepted. 3.6\When the user unit raises an objection to the product quality and needs arbitration, the arbitration institution shall be selected by both parties through consultation. During the arbitration, the arbitration analysis shall be conducted in accordance with the inspection method specified in the standard.
4 Packaging, marking, storage and transportation
4.1 Ethoxyazole crude oil shall be packaged in clean and dry polyethylene plastic bags, with a net weight of 25kg per piece. Small packages shall be packaged in clean and dry brown glass bottles, with a net weight of 0.5kg per piece. 4.2 Each batch of products shall be accompanied by a quality certificate when leaving the factory. The certificate shall include the name of the manufacturer, production batch number, product name, date of manufacture, net weight, number of pieces, and proof that the product quality meets this standard. The words "food additives" shall be marked in a prominent position, and the packaging barrel or bottle shall be accompanied by instructions for use and storage conditions.
4.3 During transportation and storage, loading and unloading shall be light and efficient, and rain and sun shall be prevented. Vehicles and ships shall be clean, non-toxic and odorless. It is strictly forbidden to store them together with toxic items or other contaminated substances. When storing, it should be placed in a cool place and avoid direct sunlight. 4.4 The shelf life of this product is one year.
Additional Notes:
This standard is under the jurisdiction of Beijing Chemical Research Institute of the Ministry of Industry and Food Hygiene Supervision and Inspection Institute of the Ministry of Health. This standard was drafted by Shanghai Pesticide Research Institute and participated in by Shanghai Changzheng Second Chemical Plant. The main drafters of this standard are Ye Wenbing, Yao Junqing and Li Hougen. People's Republic of China
National Standard
GB 8849 .. 88
Published by China Standards Press
(Beijing Fuwai-Lihe)
National Standard Selection Press Beijing Printing! Printed
Xinhua Madian Beijing Publishing House Distributed by Xinhua Bookstores in all regions. Copyright reserved
Not allowed to print
80×12301/16 Printing sheet1/2
Word count 900
March 1989 edition
March 1989 First printing and deletion
Print run 1-3 000
Word book: 1550661-6066
Dongri 10
Starting price 0.40 yuan
8810e2
88-6±8890
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.