This standard only stipulates the combined gaskets for welding, ferrules, expanded pipe joints and plug seals, with a nominal pressure of 400kgf/cm2 and an operating temperature of -25~80℃. JB/T 982-1977 Combined sealing gasket JB/T982-1977 Standard download and decompression password: www.bzxz.net
Some standard content:
Ministry of Machinery Industry of the People's Republic of China Ministry Standard Combined sealing gasket JB 982-77 replaces JB982- 67 This standard only stipulates the combined gaskets for welding, ferrules, flared pipe joints and plug seals, nominal pressure, 400kgf/cm*, working temperature -25~80°c. Less than 0.15 ofy Marking example: d f D Combined sealing gasket with nominal diameter 27mm: Gasket 27JB982— 77 0-2 of The remaining 2 piece 1 and piece 2 are glued during vulcanization|tt||The First Machinery of the People's Republic of China The Ministry of Industry issued the Standardization Research Institute of the First Ministry of Machinery Industry proposed on May 1, 1977 Implementation Jinan Casting and Forging Machinery Research Institute and others drafted 2 A total of 3 tops Page 2| |tt||Nominal diameter d. Tolerance Dimensions 8 10 12 14| |tt||16 18 20 22 24 27 30 33||tt ||36 39 42 45 48 52 60 8.4 10.4 124 14.4 16.4 18.4 20.5 22.5 24.5 27.5| |tt||30.5 33.5 36.6 39.6 42.6 45.6 48.7www.bzxz.net 52.7||tt ||60.7 d2 1 size 10 12 ±0.12 ±0.14 ±0.17| |tt||±0.20 14 16 18 20 23 25 27|| tt||30 33 36 40 43 46 49 52||tt| |56 64 JB982-77 mm D Tolerance +0.24 +0.28|| tt||+0.34 +0.40 size 14 16 18 20 22|| tt||25 28 30 32 35 38 42 46||tt| |50 53 56 60 66 75 Tolerance -0.24 0.28 -0.34 -0.40 Material: Piece 1----Oil-resistant rubber I-4, Piece 2——A2. Technical conditions h 2.7 2.9 hole d charge allowed eccentricity 0.1 0.15||tt ||1. The physical and mechanical properties of oil-resistant rubber 14 should comply with the regulations of GB123576. Table 1 Applicable thread sizes M8 M10(G1/8\) M12 M14(G1/4\)||tt| |M16 M18 (G3/8\) M20 M22(G1/2\) M24 M27(G3/4\) M30 M33(G1) M36 M39 M42(G11/4\) M45 M48 M52 M60 (G2\) 2. The sharp edge of part 1 must maintain a complete edge. Bubbles, impurities and convex-like defects are not allowed on the outer surface within 0.511m on both sides of the sharp edge. Allowable defects on other surfaces are as specified in Table 2. Nominal diameter 8~18 >18 gas bubble bubble diameter shall not be greater than 0.3 mm shall not be more than 2 places | |tt | Exceeding 0.3 mm2 shall not exceed 2 places The impurity area shall not exceed 0. 3 mm2 shall not exceed 3 places 3. The surface of Part 2 must be smooth and free of rust and other surface defects. Page 3 of 3 Table 2 Concave and convex defects The convexity shall not exceed o.3mm The area shall not exceed 0.6 mm2 shall not exceed 2 The unevenness at shall not exceed 0.4mm and the area shall not exceed 0.7mm2 shall not exceed 2 4. The bonding strength of parts 1 and 2 must be greater than the tear strength of the rubber. Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.