JB/T 2001.68-1999 Types and dimensions of single pipe clamps for water systems
Some standard content:
IC.s$ 23.110
Machinery Industry Standard of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
National Machinery Industry Bureau
2(-01-U1 Implementation
Machinery Industry Standard of the People's Republic of China
Water system single pipe clamp type and size
Water system Single pipe clamp -Type uml sizeThis standard specifies the type and size of single pipe clamps. This standard is applicable to single pipe clamps for high pressure and low pressure hydraulic circuits: 2 types and sizes
2. The types and sizes of single pipe clamps with outer diameter of pipe: 4-38mm shall be in accordance with the provisions of Table 1 and Table 1, JB/7 2001.69--1$99
Generation JB 2071—84
2.2 The connected single-tube with an outer diameter of 12.60mm is divided into two structures: straight welding and fastening on the support frame, and the core type and size are used in accordance with the provisions of Figure 25 and Table 25.
2.3 The connected single-tube with an outer diameter of 73~426mm is also divided into two types: straight welding and fastening on the support frame, and the flat type and the control type. Figure 3. Figure 6 and Table 5. Table 6 stipulates
2.4 The single-section fire of the Nozzle type pipe with an outer diameter of 73~426mm is directly welded! Fastened to the bracket 1, the two structures are the same as the size and text Figure 4, Figure 7, Table 4, Table? The selection and installation of the simple clamp
The selection and installation of the pipe can be seen in the engraving A (the Appendix 4 marking example of the prompt
Single pipe clamp with an outer diameter of 14mm:
Single pipe 14IB/2001.68—1999
—Pressing plate: 2—Sleeve: J—Screw: 1—Ruler drawing:
Approved by the National Machinery Industry Bureau on 1-16-28
200001-0 Implemented
JB/1 2X1 6X 1
IB/T 20G1.68.2
JBT 2KUJ.68.3
1R:T 2001.68.4
J1 20KJ1 68.5
JB-T 2001.68.6
JT5:T2001.6R.
JI5/1 2001.6RS
JB.T 2001.6 8.
JB/T 2091.68.19
JR/T 2001.G8.11
11 2111.6x 12
JBT 2001.65.13
JB/T3001.68-1999
1--Pull: 2-Gauge: 3-1 General tip: 4-Replacement pad: 5-Lower general light 2
Dish column 2×d
2×M12
Screw #2×
2×M16
2×MIs
:B/200).68.14wwW.bzxz.Net
JVT 2001 68.15
JB:T 2001 68.[6
JR/T 2001.G8.17
JR:1 2XH hX.1X
JB.T 240L.63.15
JB/T2001.65.20
JB.F 201.65.2
FT 2001.6B.22
J4/21.8.2.3
JJ5/1 2111 68.24
JBT 2001.68 .25
J1B/Y2001.68.26
JB/T2001.68.27
J13/1 2001.68 28
[BT 200L.68 24
JWT 200:.68.30
JB/ 2001 56.31
IR:T 20n1 6S.32
JB:1 263I h8 33
JB/I209E.6R.34
JB/T2001.68—1999
1-half ±:7, worry ratio: one meter:4-drying pad:5-section element diagram 3
2×M73
2 ×M30
2 × M3G
ID-T 209L.68.35
JPT2001.68.3G
A 2UJ1 6K\7
JB-T 20G1.68.38
JE2001.68.39
IR:120K:1.68.1
BT200168—1999
1Combustion discharge: 2.Frequency disk: 31Real clamp: 4Strong force: 5Down clampFigure 4
2×M22
4 × 5120
B[2001.68.41
Month/T 2001.68,42
JB,C 2001.68.43
JB:T 2001.68.44
J4-T 211 68. 15
J3/T 2001.68.46
J3:T 2001.68.47
J4/T 2UJI1 6 48
JN/T 2001.68.49
JR/T2nOJ.68.50
JB:T 2001.68.5E
JB :7 2001.66.52
JH/I 21KI1.68.53
JB-T 2001.68.54
3B-T 2001.68.55
I 7(K1 68 56
JB/T 20G1.68 57 | | tt | | tt | 68.69
JB/[20u168.70
21J1 8.71
3:T 2001 68.72
JR/T 2001.68.73
JB,T 2L.68.74
JB/T 2601.68.75|| tt||JH/[ 2401.65 7h
JB/T2001.68-1995
Table 4 (
$36286
61h!326
=×M20
4 × M25
a ×M25
4×M25
4×M24
2×M24
4×M24
2×M24
4× M74
2 ×M13
4 30
4 × M3
2 × M3
1 × M30
2 ×M30
4 x3130
7 k M5h
4 × ×436
481
JB/T2M1.68—1999
1 clamp: 2-end: 3-screw; 4-scorpion 5
1 mast: 2-nut: 3
rubber pad: 4.-body
reverse Du 2xd
7×M1h
JB.T 2001.68.82
JB.T2001.68.83
J[3-T 2001.68.54
JB-T2001.68.55
JBT2001.6B.36
JBT2001.6B.97
JRT200J.68.88
JHr1 2001.68.89
I ZUI 6R,*||t t||3BrT 2u01.68.9
JB/T2U01.68.93
JBT 2001.68.93
J3.T 2601.68.94
J3-T 2001.6R.95
J3/T 2001.68.96
J3/T 20D1.68.97
JBT 2001.68.98
H/Txt.68.99
T218.1(M)
115/1 2111 68. 101
JH:T20U1.68.102
JE/T2001.68—1999
300200
1. Explosion column: 2 Burning world: 3.- Rubber car; 4- Spray clamp sample rate, 7
2 ×M2:
2 × V2
2 xv3n
2×M36
J3.T 2001.65.10+
J/T 2001 68.105
32/ 2001.69.306
JS.T 2001.ER.10?
J//T 2001.48.J0S
JH/12O1.68.109
F1 2001.e8.1:0
1/r hal 6. p11
HE241 68.[12
J3.T 201.6&13
J/T 2CO1.68.114
JT 2031 6811 | |tt | |tt||JB:T 2(O1.68. [22
J/T2001.68.123
JB/T2001.6B—1999
[20240
:190
2×24
2×M50
2×M3b
JB/T2801.68-1999
Appendix A
(Appendix of Prompt)
Selection and Installation of Arms
People! This standard lists the steel, joint, and cast single-tube lights of seven god structures. The selection of the standard production conditions is determined. Seven types of campfires use the method of welding the bottom screen or bottom plate (forged type) with the base bracket and the single-tube flame according to the column and the pipe bracket to determine the two types of application of the pipe system.
A For pipes with outer diameter D, 38mm, select only one type according to table 2. -42-60mm, select only two types according to table 2 and table 3: When the pipe outer diameter D is 73.-426mm, select only four types according to table 3, table 4, table 6 and table 7. When mixed, pay attention to whether the center mark size is the same, or the support height must be adjusted. A3 For pipes with outer diameter 0=4-60mm, single type, high or low, all single type is used. For pipes with outer diameter 73-426mm, single type is used when the system pressure is PN10mA, and double type is used when PN20mA. The investor can also choose single or double row single pipe according to the specific situation of pipeline layout. When using double row, two single pipes are placed on the base bracket, side by side, and the weld should be extended as far inward as possible from the inner side of the flange plate (cell) to the inner side of the flange plate (cell). The single pipe with an outer diameter of D = 71-426mm (B/T2001.68.35.76) is divided into single row and double row types. Single row is single number and double row is double number. The double row is designed according to the effective value E of the table 7.
A6 single pipe top buried steel plate, it is recommended to use 1-shaped steel welding embedded parts. The length of the embedded steel plate [from 500mm, use the structure of Figure A]: >500mm, use the structure of Figure A2. The length of the embedded steel plate and the thickness of the embedded plate are determined by the designer, Figure AI68-1999
Appendix A
(Reminder Appendix)
Selection and installation of the arm
People! The single-tube light pipes of steel, welded, and cast structures listed in this standard are selected according to the production conditions. Seven types of campfires use the method of welding the bottom screen or bottom plate (forged type) with the base bracket and the single-tube heat pipe system with two types of columns and pipe brackets.
A The outer diameter of the pipe is D, singing 38mm, and only one type of outer diameter of the pipe is selected according to the table. -42-60mm, there are only two types in Table 2 and Table 3: When the outer diameter of the pipe is 73.-426mm, there are only four types in Table 3, Table 4, Table 6 and Table 7. When mixed, it should be noted whether the center mark size is the same, whether it is necessary to adjust the support height A3. For single pipes with an outer diameter of 0=4-60mm, no matter high or low, single pipe clamps are used. For single pipe clamps with an outer diameter of 73-426mm, regardless of the type, single pipe clamps are used when the system pressure is PN10Ma, and double pipe clamps are used when PN20MPa. The investor can also choose single or double row single pipe according to the specific situation of pipeline layout. When using double row, two single pipes are placed on the base bracket, side by side, and the weld should be extended as far inward as possible from the inner side of the flange plate (cell) to the inner side of the flange plate (cell). The single pipe with an outer diameter of D = 71-426mm (B/T2001.68.35.76) is divided into single row and double row types. Single row is single number and double row is double number. The double row is designed according to the effective value E of the table 7.
A6 single pipe top buried steel plate, it is recommended to use 1-shaped steel welding embedded parts. The length of the embedded steel plate [from 500mm, use the structure of Figure A]: >500mm, use the structure of Figure A2. The length of the embedded steel plate and the thickness of the embedded plate are determined by the designer, Figure AI68-1999
Appendix A
(Reminder Appendix)
Selection and installation of the arm
People! The single-tube light pipes of steel, welded, and cast structures listed in this standard are selected according to the production conditions. Seven types of campfires use the method of welding the bottom screen or bottom plate (forged type) with the base bracket and the single-tube heat pipe system with two types of columns and pipe brackets.
A The outer diameter of the pipe is D, singing 38mm, and only one type of outer diameter of the pipe is selected according to the table. -42-60mm, there are only two types in Table 2 and Table 3: When the outer diameter of the pipe is 73.-426mm, there are only four types in Table 3, Table 4, Table 6 and Table 7. When mixed, it should be noted whether the center mark size is the same, whether it is necessary to adjust the support height A3. For single pipes with an outer diameter of 0=4-60mm, no matter high or low, single pipe clamps are used. For single pipe clamps with an outer diameter of 73-426mm, regardless of the type, single pipe clamps are used when the system pressure is PN10Ma, and double pipe clamps are used when PN20MPa. The investor can also choose single or double row single pipe according to the specific situation of pipeline layout. When using double row, two single pipes are placed on the base bracket, side by side, and the weld should be extended as far inward as possible from the inner side of the flange plate (cell) to the inner side of the flange plate (cell). The single pipe with an outer diameter of D = 71-426mm (B/T2001.68.35.76) is divided into single row and double row types. Single row is single number and double row is double number. The double row is designed according to the effective value E of the table 7.
A6 single pipe top buried steel plate, it is recommended to use 1-shaped steel welding embedded parts. The length of the embedded steel plate [from 500mm, use the structure of Figure A]: > 500mm, use the structure of Figure A2. The length of the embedded steel plate and the thickness of the embedded plate are determined by the designer, Figure AI
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.