This standard specifies the types and dimensions of screw-type lamp holders. This standard applies to the design and production of screw-type lamp holders for electric light sources, and also applies to the design of electric light source products. GB 1406-2001 Types and dimensions of screw-type lamp holders GB1406-2001 Standard download decompression password: www.bzxz.net

GB14062001
All technical contents of this standard are mandatory. Former
This standard is equivalent to the International Electrotechnical Commission IEC60061-1:1969 "Lamp holders, lamp holders and gauges for testing their safety and interchangeability Part 1: Lamp holders" and its 1970-1999 revisions, and its technical contents are completely consistent with the loose-leaf pages in IFC60061-1: 7004-25-3: 7001-22-6; 7004-30-2: 7004-7-1: 7004-116-1; 7001-28-2; 7004-23-6: 7004-26-2: 7004 21 8; 7004 27 3; 7004-24-6.
After the implementation of this standard, the original GB1406:1989 "Types and dimensions of screw-type lamp holders" will be abolished. This standard is proposed by the State Bureau of Light Industry.
This standard is under the jurisdiction of the Electric Light Source and its accessories branch of the National Technical Committee for Standardization of Lighting Appliances. The drafting units of this standard are: Shanghai Jiabao Guangming Lamp Holder Co., Ltd. and Beijing Electric Light Source Research Institute. The drafters of this standard are Li De, Zhu Xiaoxing, Lian Song and Yang Xiaoping. 457
GB#4062001
IEC Foreword
1. The formal resolutions and agreements of the International Electrotechnical Commission (IEC) on technical issues are formulated by various technical committees, and all national committees with special interests in this regard are represented. Therefore, these resolutions and agreements express the international consensus on this issue to the greatest extent possible.
2. Recommended standards published for international use are, in a sense, adopted by national committees. 3. In order to promote international unification, the International Working Committee hopes that countries that do not have relevant national standards at present should use the IEC recommended standards as the basis for relevant standards when formulating relevant standards within the scope permitted by national conditions. 4. In order to broaden and strengthen the international consensus on these issues, it is necessary for the national committee to strive to harmonize its national standards with the IEC recommended standards when the national conditions permit. The national committees should play a role in this regard. 438
1 Scope
National Standard of the People's Republic of China
Types and dimensinns of Edison screw lamp caps
Types and dimensinns of Edison screw lamp caps This standard specifies the types and dimensions of screw lamp caps. GB 1406 2001
eqv1EC 60061-1:1969
Generation GB1406—1989
This standard applies to the design and production of screw lamp caps for electric light sources, and also to the design of electric light source products. Note: For E26 and E39 lamp holders not used in my country, please refer to the loose-leaf IEC: BC06:-1 standard: 7004-21A (E26 Lamp holder), 70(4·21A(E39 lamp holder).
2 Reference standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. The versions shown at the time of publication of the standard are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T1483--2001 Specifications for screw lamp holders (egV1EC600613:1960) QB2218-1996 Model naming method for lamp holders and lamp holders 3 Types and dimensions
3.1 The type of lamp holder shall comply with the provisions of QB2218-1996. 3.2 The type and size of screw-type lamp holders shall comply with the provisions of the following chart E5 screw-type lamp holder See Figure 1 and Table 1
10 screw lamp holder see Figure 2 and Table 2
EP10 pre-focus screw lamp holder see Figure 3 and Table 3FY10 screw lamp holder see Figure 4 and Table 4
EZ10 screw 11 lamp holder see Figure 5 and Table 5
E12 screw lamp holder see Figure G and Table 6
F14 screw recessed lamp holder see Figure 7 and Table 7
E17 screw lamp holder see Figure 8 and Table 8
E27 screw lamp holder see Figure 9 and Table 9, end See Figure 10 for the external appearance. See Figure 11 and Table 10 for E27/51×39 screw-on lamp holder. See Figure 12 and Table 11 for E40 screw-on lamp holder.
Approved by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on 2001-11-05. Implemented on 2002-05-01
GB1406-2001
E5 screw-on lamp holder
Attached figure only indicates interchangeability. Dimensions in mmE5/9
5.30 max*
min int
Not including welding
Including welding
Actual size
Stone embedded thread
The lamp holder may have a horn mouth, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without horn II by 0.5m1. For finished lamps, the creepage distance through the insulator shall not be less than 0.8mm. *This dimension is used for lamp holder design and is not used for inspection of finished lamps. Table 1
Small ruler symbol
(1) This dimension is inspected using a millimeter ruler. C
(2) "\ refers to the distance from the lamp holder connection piece to the complete thread. =
Maximum price
H10/12
GB1406—2001
E10 Screw-on lamp holder
The attached figure shows only the interchangeable dimensions, in mm. E10/13
H10/19X×13
13.0±0.1
Enlarged view of thread
With thread
The lamp holder may have a bell mouth, the diameter of which shall not exceed the maximum allowable diameter of the lamp holder without a bell mouth by 1 mm. 2
Dimension symbolwwW.bzxz.Net
T(2)(3)
Unassembled lamp holder
*This dimension is only used for lamp holder design, not for quality inspection. Note:
(1) This dimension is inspected using a millimeter ruler. (2) Refers to the maximum value of the distance from the solder end face of the lamp head to the complete thread
(under study)
(under study)
Minimum
Lamp holder on the finished lamp
Minimum value
Maximum value
Maximum value
(3) \T" For unassembled F15/12 lamp holder, this value is reduced to 7.75mm: for "finished lamp E1C/12 lamp holder, this value is reduced to 8.13mm, () for "finished lamp, the creepage distance through the insulator shall not be less than 2mm. Inspection: F10 lamp holder is inspected using the E10 lamp holder go gauge and the E10 and FY10 lamp holder stop gauge shown in CB/T14832001. 421
Small including solder
Including rape
GB 1406—2001
EP10 pre-focus screw lamp holder
The attached figure only shows the interchangeable dimensions, the unit is mm. A
Reverse is the dimensions of the near-sensitive cylindrical
LP10/14×11 lamp holder
Net (1)
Enlarged view of screw damage
With screw
The lamp holder can be equipped with a horn, the diameter of which shall not exceed the maximum allowable diameter of the skirt by 1mm. For the finished lamp, the storage distance through the insulator shall not be less than 2mm. Table 3
Dimension symbol
Minimum value
Unassembled lamp holder·
Nominal value 2.3
Maximum value
Lamp holder on finished lamp·;
This dimension is only used for lamp holder design and is not used for inspection of finished lamps. **This dimension is inspected using the EF10 lamp holder pass gauge shown in GB/T: 485~2001. Unless otherwise specified Note:
(1) \T refers to the distance between the effective thread end and the 1(,1mm reference. (2) Determined by the theoretical thread section - only with" gauge design, no lamp cap inspection: (3) Inspection is carried out using the EP10 lamp cap stop gauge shown in GB/T1183-2001: 442
Maximum value
Not including lap welding
GB1406-2001
EY10 screw lamp cap
The attached figure only shows the interchangeable dimensions, in mm. EY10/IS
Recommended: K degree 13, 6mm±0.3mm2
Enclosed port
Ground
Ground
Ground
Lamp cap may be provided with a flare, the diameter of which shall not exceed the maximum permissible diameter of the lamp cap without a flare by 1 mm. 4
Dimension symbol
1(2)(3)
Minimum value
Unthreaded lamp cap,
Maximum value
(Under study)
(Under study)
This ruler is used for lamp cap design, not for inspection of lamps Note:
(1) This ruler is used for inspection in millimeters, (2) "" refers to the distance from the base to the effective complete thread, (3) R, R, M are measured at the reference circle. (4) For finished lamps, the creepage distance of the tested insulator shall not be less than mm0.531
Lamp holder on finished lamp
Minimum value
Maximum value
Inspection: The go gauge of FY10 lamp holder and the stop gauge of E10 and EY10 lamp holder shown in Sichuan G/T1483-2001 are used for inspection443
Dimension symbol
GB1406-2001
FZI0 screw-recessed lamp holder
The attached figure only shows the five-dimensional dimensions, the unit is mI, the contact position of the finished lamp||tt ||Minimum value
13.-15(4)
This dimension is used for lamp holder design and is not used for inspection of finished lamps. Note:
(1)\T\ refers to the distance from the contact piece to the effective complete thread. 2)\T\ refers to the distance from the contact piece to the effective complete thread on the finished lamp. Insulating material
Nominal value 13″
(3) The inspection is carried out using the stop gauge of E10 and EY10 lamp holders shown in GB/T1483-2601. (4) The minimum value is one of the measures taken to prevent the lamp from entering the E11 lamp box. (5) For new designs, this value is reduced by 4 mmFor finished lamps, the creepage distance through the insulator shall not be less than: 1.5 mum. 211
Right loose thread
Maximum value
(to be determined)
Not including welding radius
GB 1406—2001
E12 screw-type lamp holder
Attached instrument indicates interchangeable dimensions in mm. 512/15
190F60
Head This dimension is used for lamp holder design and is not tested. The lamp holder may have a flared mouth, the diameter of which shall not exceed 12.32 mm. Table 6
Dimension symbol
Minimum
Unassembled lamp holder "
Maximum value
This dimension gauge is used for lamp holder design and is not used for inspection of finished lamps. Note:
(1) This dimension is inspected using a ruler. (2) "T\ refers to the distance from the contact piece to the effective complete thread. (3) "T1\ refers to the distance from the weld end face to the effective complete thread, 0.792
(4) This dimension is obtained from the theoretical thread profile - the instrument is designed based on the gauge, and no lamp cap inspection is performed. The lamp cap of the finished lamp is inspected using the performance contact gauge, through gauge, additional through gauge and stop gauge shown in GB/T1483-2001. The lamp cap of the unassembled lamp is inspected using the performance contact gauge, through gauge, additional through gauge and stop gauge shown in GB/T1483-2001. 1406—2001
E11 screw-on lamp holder
The attached figure shows only the interchangeable dimensions, in mm.E14/23X15
15.0±0.1
Right thread
Excluding solder
Including paste
E14/25×17
17.0±0.1
The lamp holder may have a bell mouth, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a bell mouth by 1mm. For finished lamps, the creepage distance through the insulator shall not be less than 3 mm. ?This value indicates the diameter of the reference circle to which dimensions 5 and S should refer: Table?
Scale symbol
Wooden assembled lamp holder
Minimum
Maximum
Minimum value
*This scale is only used for lamp holder design and is not used for inspection of finished lamps. Note:
(1) This dimension is inspected using a millimeter scale
(2) "T\" refers to the distance from the contact piece to the effective complete thread. (3) \T,\ refers to the distance from the end face of the welded coupling to the effective light-year thread. 6. 2
(4) This dimension is obtained from the theoretical thread section and is only used for design specifications and is not used for inspection of lamp holders and lamp holders. 446
or lamp cap on product lamp
minimum
maximum
maximum
1G. 27 max
E17/20
GB 1406—2001
E17 screw-type lamp cap
The attached figure shows only the dimensions of the sheet, in mm. Including welding series
small Including welding series
The lamp cap may have a flare, and its diameter shall not exceed the maximum allowable diameter of the lamp cap without a flare by 1Im. Table 8
Dimension symbol
Unassembled lamp cap·
minimum
*This ruler is used for lamp cap design and is not used for inspection of finished lamps. Note:
(1) This dimension is inspected using a ruler. (2) \" refers to the distance from the contact piece to the effective complete thread: (3) "\" refers to the distance from the end face of the weld to the effective complete thread. Minimum value
Maximum value
Lamp holder on finished lamp
Minimum value
Maximum value
E27/25
min int
GB1406—2001
E27 screw lamp holder
The attached figure only shows the interchangeable dimensions, the unit is mm. E:27/27
minint
9“0+,9'92
Butterfly pattern enlarged view
Right screw system
Excluding welding width
Including welding
The lamp holder can be equipped with a flare, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a flare by 1mm. For finished lamps, the distance of the electric field through the insulator shall not be less than 3 mm.118No lamp cap inspection is performed.
Finished lamp!
Minimum value
Maximum value
Inspection: The E12 lamp cap on the finished lamp is inspected using the performance contact gauge, through gauge, additional through gauge and stop gauge shown in GB/T1483-2001. Unassembled lamp cap*
514/20
min int,
Lamp cap on the finished lamp
GB 1406—2001
E11 screw-on lamp holder
The attached figure shows only the interchangeable dimensions, in mm.E14/23X15
15.0±0.1
Right thread
Excluding solder
Including paste
E14/25×17
17.0±0.1
The lamp holder may have a bell mouth, the diameter of which shall not exceed the maximum permissible diameter of the lamp holder without a bell mouth by 1 mm. For finished lamps, the creepage distance through the insulator shall not be less than 3 mm. ?This value indicates the diameter of the reference circle to which dimensions 5 and S should refer: Table?
Scale symbol
Wooden assembled lamp cap
Minimum
Maximum
Minimum value
*This scale is only used for lamp cap design and is not used for inspection of finished lamps. Note:
(1) This dimension is tested using a millimeter scale
(2) "T" refers to the distance from the contact piece to the effective complete thread. (3) "T" refers to the distance from the end face of the welded coupling to the effective light-year thread. 6. 2
(4) This dimension is obtained from the theoretical thread section and is only used for design and is not used for inspection of the cap and lamp holder. 446
Or lamp cap on a product lamp
Minimum value
Maximum value
Maximum value
1G. 27 max
E17/20
GB 1406—2001
E17 screw-on lamp holder
The attached figure shows only the dimensions of the lamp holder, in mm. Including welding
Including welding
The lamp holder may have a bell mouth, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a bell mouth by 1mm. Table 8
Dimension symbol
Unassembled lamp holder·
Minimum price
*This ruler is used for lamp holder design , no inspection is done on the finished lamp. Note:
(1) This dimension is inspected with a ruler. (2) \" refers to the distance from the contact piece to the effective complete thread: (3) "\" refers to the distance from the end face of the weld to the effective complete thread. Minimum value
Maximum value
Lamp holder on the finished lamp
Minimum value
Maximum value
E27/25
min int
GB1406—2001
E27 screw lamp holder
The attached figure only indicates the interchangeable dimensions, in mm. E:27/27
minint
9“0+,9'92
Butterfly pattern enlarged view
Right screw system
Excluding welding width
Including welding
The lamp holder may have a flare, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a flare by 1mm. For finished lamps, the distance of the electric field through the insulator shall not be less than 3 mm. 118No lamp cap inspection is performed.
Finished lamp!
Minimum value
Maximum value
Inspection: The E12 lamp cap on the finished lamp is inspected using the performance contact gauge, through gauge, additional through gauge and stop gauge shown in GB/T1483-2001. Unassembled lamp cap*
514/20
min int,
Lamp cap on the finished lamp
GB 1406—2001
E11 screw-on lamp holder
The attached figure shows only the interchangeable dimensions, in mm.E14/23X15
15.0±0.1
Right thread
Excluding solder
Including paste
E14/25×17
17.0±0.1
The lamp holder may have a bell mouth, the diameter of which shall not exceed the maximum permissible diameter of the lamp holder without a bell mouth by 1 mm. For finished lamps, the creepage distance through the insulator shall not be less than 3 mm. ?This value indicates the diameter of the reference circle to which dimensions 5 and S should refer: Table?
Scale symbol
Wooden assembled lamp cap
Minimum
Maximum
Minimum value
*This scale is only used for lamp cap design and is not used for inspection of finished lamps. Note:
(1) This dimension is tested using a millimeter scale
(2) "T" refers to the distance from the contact piece to the effective complete thread. (3) "T" refers to the distance from the end face of the welded coupling to the effective light-year thread. 6. 2
(4) This dimension is obtained from the theoretical thread section and is only used for design and is not used for inspection of the cap and lamp holder. 446
Or lamp cap on a product lamp
Minimum value
Maximum value
Maximum value
1G. 27 max
E17/20
GB 1406—2001
E17 screw-on lamp holder
The attached figure shows only the dimensions of the lamp holder, in mm. Including welding
Including welding
The lamp holder may have a bell mouth, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a bell mouth by 1mm. Table 8
Dimension symbol
Unassembled lamp holder·
Minimum price
*This ruler is used for lamp holder design , no inspection is done on the finished lamp. Note:
(1) This dimension is inspected with a ruler. (2) \" refers to the distance from the contact piece to the effective complete thread: (3) "\" refers to the distance from the end face of the weld to the effective complete thread. Minimum value
Maximum value
Lamp holder on the finished lamp
Minimum value
Maximum value
E27/25
min int
GB1406—2001
E27 screw lamp holder
The attached figure only indicates the interchangeable dimensions, in mm. E:27/27
minint
9“0+,9'92
Butterfly pattern enlarged view
Right screw system
Excluding welding width
Including welding
The lamp holder may have a flare, and its diameter shall not exceed the maximum allowable diameter of the lamp holder without a flare by 1mm. For finished lamps, the distance of the electric field through the insulator shall not be less than 3 mm. 118
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.