title>JB/T 6546.1-1999 Woodworking multi-purpose machine tool parameters - JB/T 6546.1-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 6546.1-1999 Woodworking multi-purpose machine tool parameters
JB/T 6546.1-1999 Woodworking multi-purpose machine tool parameters

Basic Information

Standard ID: JB/T 6546.1-1999

Standard Name: Woodworking multi-purpose machine tool parameters

Chinese Name: 木工多用机床 参数

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-05-14

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Wood Technology >> Woodworking Equipment >> 79.120.10 Woodworking Machinery

Standard Classification Number:Machinery>>General processing machinery and equipment>>J65 woodworking machine tools and machine tools

associated standards

alternative situation:ZB J65006-1989

Procurement status:guest 69 NEQ

Publication information

other information

Focal point unit:Fuzhou Woodworking Machine Tool Research Institute

Publishing department:Fuzhou Woodworking Machine Tool Research Institute

Introduction to standards:

JB/T 6546.1-1999 This standard is a revision of ZB J65 006-89 "Woodworking Multi-purpose Machine Tool Parameters". During the revision, only editorial modifications were made in accordance with relevant regulations, and the technical content has not changed. This standard specifies the parameters of multi-purpose woodworking machine tools. This standard applies to multi-purpose woodworking machine tools such as woodworking machine tools with three functions of planing, planing and sawing or four-purpose woodworking machines with planing, planing, sawing and drilling. This standard does not apply to desktop woodworking multi-purpose machine tools. This standard was first published on March 30, 1989. JB/T 6546.1-1999 Woodworking multi-purpose machine tool parameters JB/T6546.1-1999 Standard download and decompression password: www.bzxz.net

Some standard content:

ICS79.120.10
J65
JB
Machinery Industry Standard of the People's Republic of China
JB/T6546.16546.2-1999
Woodworking multi-purpose machine tools||tt| |Released on 1999-05-14
National Machinery Industry Bureau
Released
Implemented on 2000-01-01
JB/T6546.11999
Foreword| |tt|| Parameters" revision, the revision was only edited in accordance with relevant regulations. This standard is a modification of ZBJ65006-89 "Wood T. Multipurpose Machine Tools, and the technical content has not changed.
This standard replaces ZBJ65006-89 from the date of implementation. Appendix A of this standard is a reminder appendix.
This standard is proposed by the National Machine Tool and Tool Standardization Technical Committee. This standard is under the jurisdiction of Fuzhou Machine Tool Research Institute. The unit responsible for drafting this standard: Sichuan Dujiang Woodworking Machine Tool Factory. The main drafters of this standard: Liu Yubi and Chen Jiaju. This standard was first released on March 30, 1989. 2
Scope
Machinery Industry Standard of the People's Republic of China
Parameters
Woodworking multi-purpose machine tools
This standard specifies the parameters of woodworking multi-purpose machine tools. JB/T6546.1-1999
replaces ZBJ65006-89
. This standard does not apply to desktop woodworking multi-purpose machine tools. Parameters
The type of woodworking multi-purpose machine tool is shown in Figure 1 (the specific structure is not limited), and the parameters should comply with the table! Provisions. 1 One-pin L-making table; 2 One-pin rigid board; 3-Drilling (planing, cutting) shaft; 4-Planning guide plate: 5 Planing 1 making table: 6 Planing guide plate; 7 One-sided saw blade: 8 Yizi Saw T Work Table: 9 Lemin T Work Table Picture 1
Table 1
Main Parameter Name
General Increase 1 Width
National Machinery Industry Bureau 1999 -05-14 approved 250
main
dream
315
number
400
mm
2000-01 -01 Implementation
JB/T 6546.11999
Appendix A
(prompted appendix)
Other basic parameters of woodworking multi-purpose machine toolsbZxz.net
A1 wood T. Other basic parameters of multi-purpose machine tools are shown in Table A1. Table A1
Parameter name
Maximum diameter of main staggered piece
Maximum aluminum hole diameter
Maximum groove width
Parameter value||tt| |200#250;315:400
13;20
16
mm
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.