This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation, storage and other requirements of skin lotions. This standard is applicable to water-in-oil emulsion cosmetics with fluidity that moisturizes human skin. QB/T 2286-1997 Skin lotion QB/T2286-1997 standard download decompression password: www.bzxz.net

QB/T 2286—1997
This standard is revised based on GB11431-1989 "Moisturizing Lotion". The main changes are as follows: - It is compiled in accordance with GB/T1.1-1993 "Guidelines for Standardization Work Unit 1: Drafting and Expression Rules for Standards Part 1: Basic Provisions for Standard Compilation";
- The relevant parts use the method of quoting QB/T1684-1993 "Cosmetics Inspection Rules" and QB/T1685-1993 "Appearance Requirements for Cosmetic Product Packaging" to replace the original technical content; - The hygiene indicators are cancelled;
- The classification and grading regulations are cancelled;
- The heat resistance indicators and the test methods for heat resistance and cold resistance are changed; - The content indicators and test methods are implemented in accordance with the National Technical Supervision Order [1995] No. 43 "Measurement Supervision Regulations for Quantitative Packaged Goods". This standard is proposed by the Quality Standards Department of China Light Industry Association; This standard is under the jurisdiction of the National Cosmetics Standardization Center. The drafting unit of this standard: Shanghai Phoenix Daily Chemical Co., Ltd. The main drafters of this standard: Yao and Xing Jing. From the date of implementation, this standard will replace GB11431--1989 "Moisturizing Lotion". 1 Scope
Light Industry Industry Standard of the People's Republic of China
Moisturizing Lotion
QB/T 2286
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation, storage and other requirements of moisturizing lotion.
This standard is applicable to water-in-oil emulsified cosmetics with fluidity that moisturizes human skin. 2 Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB 7916—1987 Hygienic Standard for Cosmetics
GB5296.3·1995 Instructions for Use of Consumer Products General Labeling for CosmeticsGB/T13531.1-1992 General Inspection Method for Cosmetics Determination of pH ValueQB/T1684—1993 Inspection Rules for CosmeticsQB/T16851993 Requirements for the Appearance of Cosmetics Product Packaging3 Product Classification
Divided into various specifications according to the color, fragrance and packaging form of the lotion. 4 Technical Requirements
Product hygiene indicators shall comply with the relevant requirements of GB 79164.1 Sensory indicators and physical and chemical indicators shall be in accordance with Table 1. 4.2 Net content tolerance (average of 10 bottles) See Table 2. 4.3 Appearance requirements
Should comply with the provisions of QB/T1685.
Sensory index
Physical and chemical index
Centrifugal test
Conform to enterprise regulations
Conform to enterprise regulations
4. 5~~8. 5 (Except for fruit acid products)
41r:24h, no oil-water separation after returning to air temperature Requirements
-5~—15℃24h, no oil-water separation after returning to room temperature 2000r/min cabin rotation for 30min without stratification (Except for insoluble powdery particle sediment) China Light Industry Federation 19970410 Approved
1997-12-01 Implementation
5 Test method
5.1 Color
>30-~40
40~~55
>55~70
>70～80
Take the sample and visually inspect it under non-direct sunlight conditions. 5.2 Fragrance
QB/T 2286—1997
Dip the sample with fragrance identification paper and use a finger to identify it. 5.3 Structure bzxZ.net
Rub the sample on the skin and observe it indoors without direct sunlight. 5.4 pH value
Determine according to GB/T13531.1 method.
5.5 Heat resistance
5-5.1 Instruments
a) Thermometer: 0.5℃ graduation value, 1 piece;
b) Electric constant temperature incubator: sensitivity ±1C, 1 piece. 5.5.2 Operation
Pour the sample into two 20mm×120mm test tubes respectively, make the liquid level about B0mm, and put on clean soft plugs. Place one of the test tubes to be tested in a constant temperature incubator pre-adjusted to the specified temperature ±1℃, take it out after 24 hours, and compare it with the sample in the other test tube after returning to room temperature.
5.6.1 Instruments
) Thermometer: graduation value 0.5℃, 1 piece
b) Refrigerator: sensitivity ±2, 1 piece.
5.6.2 Operation
Put the samples into two 20mm×.120mm test tubes respectively, make the liquid level about 80mm, and plug them with clean soft plugs. Place one of the test tubes to be tested in a refrigerator pre-adjusted to the specified temperature ±2℃, keep it for 21 hours, take it out, and compare it with the sample in the other test tube after returning to room temperature.
5.7 Centrifugal test
5.7.1 Apparatus
a) Centrifuge: 1 unit;
b) Centrifuge tube: 2 units with 10ml scale,
c) Electric constant temperature incubator: sensitivity ±1°C, 1 unit d) Thermometer: graduation value 0.5°C, 1 unit
5.7.2 Operation
Pour the sample into the centrifuge tube to about two-thirds of its height and fill it tightly. Chill it with a cork. Then put it in an electric constant temperature incubator pre-adjusted to 38±1°C. After keeping it moist for 1 hour, immediately move it into the centrifuge and adjust the centrifugal speed to 2000r/min. Rotate it for 30 minutes and take it out for observation.
5.8 Net content tolerance
5.8. 1 Operation method
QB/T 2286—1997
Take 10 bottles of sample, weigh their gross weight, then remove the contents, wash and dry, weigh their tare weight again, and calculate according to formula (1), AQ=
Where: AQ-sample net content tolerance, name: Q
sample marked net content·B:
Qi——sample actual net content·g:
n——test number is 10.
If the sample net content is marked in milliliters, the sample net content must be converted to the sample density (25℃), and then the net content tolerance is calculated according to formula (1). 5.9 Appearance test
Perform according to QB/T 1685.
6 Inspection rules
According to QB/T 1684.
7 Marking, packaging, transportation, storage
7.1 Marking
The marking of large and medium packages shall be in accordance with 3.9.5, 3.10.2.3, 3.10.3.3 of QB/T1685, and the marking of sales packages shall be in accordance with GB5296.3.
7.2 Packaging
According to QB/T 1685.
7.3 Transportation
Cartons must be loaded and unloaded with care, and stacked according to the arrow marks on the boxes to avoid severe vibration, impact, and exposure to sunlight and rain. 7.4 Storage
Finished products should be stored in a dry and ventilated warehouse with a temperature not higher than 38°C. When stacking, they must be 20cm from the ground and 50cm from the inner wall, with a passage in the middle. They must not be placed near water sources and air. The principle of first in, first out should be strictly followed.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.