HG/T 2080-2001 Cationic fluorescent yellow 4GL500% HG/T2080-2001 standard download decompression password: www.bzxz.net

Registration No.: 10106-2002
I1G/T 2080-2001
This standard is a revision of the recommended chemical industry standard HG/T2080-1991 "Cationic Fluorescent Yellow 4GIL". The ten main differences between this standard and HG/T2080-1991 are as follows: - The specification of 250% as 100 points is cancelled, and 500% is stipulated as 100 points. - Modify some indicators in the color fastness to light and perspiration, - Modify some indicators in the color fastness to pollution of other fabrics when dyeing acrylic. The water insoluble index is adjusted from less than or equal to 0.8% to less than or equal to 0.5%. This standard will replace HG/T2080-1991 from the date of implementation. This standard was proposed by the Policy and Regulations Department of the former State Administration of Petroleum and Chemical Industry. This standard is under the jurisdiction of the National Dye Standardization Technical Committee. The drafting units of this standard: Shenyang Chemical Research Institute, Zhangjiagang Gangda Dye Chemical Factory. The main drafters of this standard are Gan Yong, Ma Junqing and Lu Xiufeng. This standard was first issued in 1980 as the standard issued by the Ministry of Chemical Industry HG/T2-1388-80, and was first revised and adjusted to the chemical industry standard HG/T 2080-1991 in 1991. The National Technical Committee for the Promotion of Dye Standards is responsible for the interpretation of this standard. 1 Scope
Chemical Industry Standard of the People's Republic of China
Cationic fluorescence yellow 4GI,
Cationic fluorescence yellow 4GL500% HG/T 2080--2001
Replaces HG/T2080-1991
This standard specifies the requirements, sampling, analysis steps, inspection rules, and marking, labeling, packaging, transportation and storage of cationic fluorescent yellow 1GL (C.1. fluorescent yellow 24). This product is mainly used for dyeing red rayon. It is a matching index K-A. Structural formula:
Molecular formula: CuH2O, N, S
Relative molecular mass: 447.54 (according to the 1997 international relative atomic mass) 2 Reference standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. All parties using this standard shall discuss the possibility of using the latest versions of the following standards. GB 2374—1994
General conditions for determination of dyeing conditionsGB/T 2381—1994
Method for determination of insoluble matter content in dyes
Method for determination of sieve fineness of dyes
GB/T 2383—1980
GB/T 2386--1980
Method for determination of moisture content in dyes and dyestuffsGB/T 2399—1980
GR/T 2402—1980
G3/T 3920—1997
Method for determination of color shade and intensity of cationic dyes on other fabrics when cationic dyes are used to dye acrylic fibersTextiles test for color fastnessColor fastness to rubbing (eqv[SO105-X12:1993)GR/T 3921.3—1997
GB/T 3922—1995
GB 4841, 1--1984bZxz.net
GB/T 61521997
GB/T 6678-1986
GB/T 8427 1998
3 Requirements
Textiles Test for color fastness Color fastness to washing (eqvISO105-C03:1989) Textiles Test for color fastness Color fastness to perspiration (cqv[SO105-F04:1994) 1/1 Dyeing Standard Depth Color Chart
Textiles Test for color fastness Color fastness to hot pressing (eqv1SO105-X11:1994) General rules for sampling of chemical products
Textiles Test for color fastness Color fastness to artificial light Xenon arc (eqvISO105-B02:1994) 3.1 Appearance: Yellow homogeneous powder.
3.2 The quality of cationic fluorescent yellow 4GL shall comply with the requirements of Table 1. Approved by the State Economic and Trade Commission on 2002-D1-24, implemented on 2002-07-01
Color (with standard product)
Intensity (for standard product), points
Moisture content, %
Water-insoluble matter content, %
IG/T2080-—2001
Quality requirements of cationic fluorescent yellow 4GI.
Table 1E
Fineness\ (the amount of residue passing through the sieve with a diameter of 250um), %, strong,
1) The fineness of products with added dust suppressants may not be assessed, 3.3
Approximately ~ slightly
The pollution of cationic fluorescent yellow 4GL to other fabrics when dyeing acrylic fiber should not be less than the requirements of Table 2. Table 2 Contamination of other fabrics by cationic fluorescent yellow 4GL when dyeing acrylic Fabric
Diamond color, grade
The color fastness of cationic fluorescent yellow 4GI. on acrylic fabric should not be lower than the provisions of Table 3. Viscose
Table 3 Color fastness of cationic fluorescent yellow 4GL on acrylic fabric Washing
Dyeing depth, % Light fastness (rainbow)
1) 0.76% (awl) Equivalent to 1/1 dyeing standard Difficulty Depth Sampling
Sweat resistance
Rub resistance
Heat pressing resistance
150℃
Color change, 4h
Sampling is done in batches, and the manufacturer takes the products mixed and evenly mixed at one time as a batch. The number of sampling barrels for each batch should meet the requirements of 6.6 in GB/T6678-1986. The packaging of the sample must be intact. When sampling, do not allow foreign impurities to fall into the product. Use a probe to sample from the upper, middle and lower parts of the barrel. The total amount of the sample must not be less than 200%. After the sample is fully mixed, it is divided into two clean, dry and well-sealed containers. Labels are attached to indicate the product name, manufacturer name, batch number, sampling period and location. One is for inspection and the other is kept for future reference. 5 Analysis steps
5.1 Determination of appearance
Visual evaluation is adopted.
5.2 Determination of dyeing color and intensity
General conditions should comply with the relevant provisions of GB2374. The dyeing method adopts the dyeing method with dye inhibitor in GB/T2399-1980. 5.2.1 Preparation of dye bath
Dyeing depth is 0.5% (wf), 2g acrylic bulked yarn is used for dyeing, and the bath ratio is 1:100. D. Prepare dye bath according to the provisions of Table 4: 0.25 g/1000 mL standard solution 0.25 g/1000 mL sample solution 100 g/L anhydrous sodium sulfate solution 10 g/L acetic acid solution 10 g/L sodium acetate solution 10 g/L slow dye 1227 solution Make up the total volume with distilled water 5.2.2 Dyeing operation HG/T 2080: Preparation of dye solution in Table 4 Follow the provisions of dyeing method with dye addition in GB/T 2399-1980. 5.2.3 Evaluation of color and intensity
According to the provisions of Chapter 6 of GB 2374-1994. 5.3 Determination of moisture content
According to the provisions of Chapter 2 of GB/T2386-1980, the drying method. 5.4 Determination of water-insoluble content
According to the provisions of GB/T2381.
5.5 Fineness
According to the provisions of GB/T2383. Use a standard sieve with an aperture of 250μm. 5.6 Determination of contamination of other fabrics when dyeing acrylic rayon shall be carried out in accordance with the provisions of GB/T2402.
5.7 Determination of color fastness on acrylic fabrics
All color fastness test specimens shall be dyed to 1/1 standard depth in accordance with the provisions of GB4841.1. Color fastness to rubbing shall be carried out in accordance with the provisions of GB/T3920. The color fastness to washing shall be carried out in accordance with the provisions of GB/T3921.3. The color fastness to perspiration shall be carried out in accordance with the provisions of GB/T3922. The color fastness to heat pressing shall be carried out in accordance with the provisions of GB/6152. The color fastness to light at 150℃ dry pressing (4h) shall be carried out in accordance with the provisions of GB/T8427. 6 Inspection rules
6.1 Inspection classification
3.1 and 3.2 of this standard are inspection items for delivery. 3.3 and 3.4 are regular inspection items, which shall be inspected once a year during continuous normal production.
6.2 Factory inspection
Cationic carbon light yellow 4GL shall be inspected by the quality inspection department of the production, and the manufacturer shall ensure that all cationic fluorescent yellow 4GL delivered by the factory meet the requirements of this standard.
6.3 Re-test
If any of the indicators in the test results do not meet the requirements of this standard, samples should be taken from the double-batch packaging for re-testing. Even if only one of the indicators in the re-test results does not meet the requirements of this standard, the entire batch of products cannot be accepted. 5
Marking, labeling, packaging, transportation and storage
7. 1 Marking, labeling
HG/T2080—2001
Each packaging barrel of cationic fluorescent yellow 4GL should be painted with a firm and clear mark, indicating the product name, specification, registered trademark, net content, manufacturer name, factory address, standard number, batch number, and production date. The batch number and production date can also be printed on the label and placed on the outside of the plastic bag in the packaging barrel together with the product quality inspection certificate. 7.2 Packaging
Cationic fluorescent yellow 1GL is packed in an iron barrel lined with a plastic bag and sealed and sealed. The net content of each package is 30kg, and other packages can be negotiated and determined with the user.
7.3 Transportation
During transportation, avoid inversion, handle with care, avoid collision, and do not damage the packaging. 7.4 Storage
Cationic fluorescent yellow 4GL should be stored in a cool, dry, ventilated place to prevent moisture and heat.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.