Some standard content:
ICS37,100.10
Machinery Industry Standard of the People's Republic of China
JB/T9122-1999
Calling machinc
1999-07-12 Issued
State Bureau of Machinery Industry
Implementation on 2000-01-01
JB.T9I23-1999
This standard is a replacement of 2BJ8701990 "Radial Collating Machine". The original standard was revised and edited. The main technical contents have changed:
No. The standard will be replaced from the date of issuance. ZB397018·90 Production standard is proposed and managed by the National Printing Machinery Standardization Technical Committee 4 Standard drafting unit: Pennsylvania Printing Machinery Co., Ltd. 4 Main drafters of the standard: Xiao Yulin, Zheng Yuanzheng, Wang Yousheng, 4 The standard was first issued on May 27, 1990. — Scope
Machinery Industry Standard of the People's Republic of China
Culling machine
JB/T9122—199Q
This standard specifies the basic specifications, technical requirements, test and inspection methods, product specifications, product quality, packaging, operation and transportation of collating machine (hereinafter referred to as collating machine) 2 Reference standards
The following standards contain provisions that are used in this standard and constitute the provisions of this standard: At the time of publication of this standard, the versions shown are all current. All standards are subject to revision. Parties using this standard should discuss the possibility of using the following new standards: GB191---1990
GB/T 5226.J1996
GB/T6388—1986
GB.T 9969.11998
GB/T 13306—[991
GBT14436—1993
GR/T 16273.1—1996
IAT30901999
Types and basic parameters
Packaging, storage and transportation, Tours mark
Industrial machinery and electrical equipment Part 1: General technical spare parts transportation, packaging, receiving and shipping marks
General provisions for industrial product instruction manuals
General provisions for industrial product guarantee documents
Graphic symbols for equipment, use of numbers
Printing presses, use of product numbers, reduction method
According to the number of times the gripper wheel rotates, it is divided into:
! Single configuration:
|b Double configuration machine
1.2 Basic parameters are as per Table 1.
Applicable book format
Certificate time to offset the fixed amount
Single long post thickness
Develop matching degree
matching book effect
Guodong Machinery Industry Kitchen 1999-07-12 approved 220153, A5 (32 bill collectionwwW.bzxz.Net
946×153, 245132 bill collection 5
307220, 44/16 bill
50-±0
3h our HI IAS F version!
9. 1.15, 18,21,24
2000-01-01 implementation
JB/T9122—1999
3.3 The number and name of the collation machine shall meet the current technical requirements
4. The collation machine shall comply with the specified specifications and the drawings and technical specifications of this document. 4.2 The collation machine can be used in combination with related mechanical equipment. It can also be used alone. The configuration mode can be adjusted according to the user's needs:
4.3 The moving parts of the collation machine shall be connected: or work in a coordinated manner, without jamming, collision, violent movement and spontaneous movement. .The control components of the machine are sensitive and reliable, ensuring that they can be arranged in order at any working position. 4.5 The pager is reliable when working, and the input and stacking of books are neat. 46 The damage rate of the matching unit is less than 0.2%. 4.7 The reliability of the whole system is less than 99%. 4.8 When the centralized lubrication system is adopted, the lubrication oil circuit is guaranteed to be unobstructed, and no blockage or leakage is allowed. 3. When the user violates the lubrication control system, the serial number 037038 in Table 1 of GD/T16271.11996, 039, and the specified mark 4.9 The bearing: the working pressure shall not exceed 35. 4. 1U sound A sound level H is not greater than 85 dB (A! 4.1 The design of the overload safety clutch of the feeding chain components shall comply with the relevant provisions of 9.2.5.4 of GB/T5226.11996. 4.12 Electrical quality
4.12.1 The stop and emergency treatment functions of the paging machine shall comply with the relevant provisions of (B/5226.1-1996119.2.2 and 9.2.5.4 for Class 0 and Class 1 parking.
4.12.2 The color of the paging button shall comply with the relevant provisions of 10.2 and 10.3 of B5226.1-1996. 4.12.3 The use of programmable 4.12.4 The continuity of the protective grounding circuit of the coin dispenser shall comply with the relevant provisions of 20.2 in GB/T5226.1-1996. 4.12.5 The insulator resistance of the electrical system shall comply with the relevant provisions of 20.3 in GB/T5226.1-1996. 4.12.6 The withstand voltage of the electrical system shall comply with the relevant provisions of 20.4 in GB/T522G1-1996. 4.13 Appearance quality
4.13.2 The exposed non-processed surface of the parts shall not have defects such as rust, bumps, and convexity. 4.13.3 The plated surface of the parts shall not have defects such as rust, blistering, and delamination. 5 Test method
5.1 Running test
5.1. The running test time shall not be less than 60 minutes. During the test, the speed of the transmission shall be judged from low to high. In addition, according to the requirements of 3.2, the page speed is 110% and the running test time is not less than 20 beats. 5.1.2 The empty rotation test should meet the requirements of 4.3 and 4.4. 5.2 Load test
5.2. The negative test can be carried out after the operation test. 5.2.2 The negative test conditions shall be controlled as follows:) Paper: m
; Standing data m:% (A4: electronic book, 32 double (A5) book (! Book hope: negative board test door Feng book into a small solid, flat, especially curling, light broken objects. Thick evil will be about: test speed: A1] book with the maximum starting speed of %, 3? Double frequency! A:) I book format before the maximum page abuse of %
:) Test agent question: 16 and (41) rough book belt standing 10min: 32 and double (2A5) rough book 10minm. 5.2.3 The load test shall comply with the provisions of 4 to 4.5 and 4.9. 5.2. The load test shall be carried out in accordance with the specifications of the standard, the starting point is 5m, the test speed is 6% of the rated maximum starting speed
5.5 When testing the average rate, continuous sampling shall be carried out, and no stop is allowed in the middle. The total number of sampling shall be less than 5: 4 is allowed to be tested in a single piece. The test results shall comply with the provisions of 4.6. 5.3 Control system test
5.3.1 The reliability of the control system shall be tested by simulation method: artificially create defects and multiple faults for the standard group, record the total number of error signals: calculate the reliability coefficient. Failures include no indication signal, signal off, no control: The control system is called non-coefficient and is calculated by the following formula:
Control system drivability coefficient - total number of signals 100% total number of signals
5.3.2 During the control system test, if there is a disturbance in the conveyor, or a blockage, the machine can automatically stop the code in time 5.3.3 The control system test results should meet the requirements of 4.7: 5.4 Before the test, the sound level meter of the machine A is used to measure the direct pressure level. The problem point is the machine: 1 m away from the center line of the word, four points with a commercial height of 1.5m: the average noise level of the four points is measured. The nesting should meet the requirements of 4.10. 5.5 Reliability test
5.5.1 Static test
Books with less than 20 taels are placed on the table, and a weight of 10 kg is added. The teeth should be able to stick evenly in each dimension.
5.5.2 Dynamic test
5.5.2. During the operation of the machine, check the teeth one by one according to the storage table. The feeling is clean. When the 5 pieces are heard, there is no slant, no sound, and no release.
5.5.2.7 The reliability of the chain overload trigger should be tested: 5.6 Visually check the lubrication system, which should meet the requirements of 4.8. 5.7 Visually check the appearance quality of the machine, which should meet the requirements of 4.13.8 Electrical quality shall be tested in accordance with 9.2, 10.2, 10.3, 20.2, 20.3, 20.4 of GB/T5226.11996. The test results shall comply with the provisions of 4.12:
6 Inspection rules
6. Before and after inspection
.! Every product shall be inspected by the quality inspection department and can be shipped out of the factory! 6.1.2 Every product shall be inspected by the quality inspection department and can be shipped out of the factory! Before the production, the following 5.1, 5.2, 5.3, 5.5, 56, 5.7, 5.8 heat tests must be carried out according to JB/19122-1999
6.1.3 The first batch of 5.4 films must be measured in accordance with the provisions of JB/19122-1999. 6.2 Type test
6.2.1 Type test shall be carried out if any of the following conditions occur: a) The product has been transferred to the production site for type determination and identification; b) After formal production, such as structure, material, and process, there are minor changes that may affect the product performance: When the product is resumed after being discontinued for 3 years. 6.2.2 Type test shall be carried out according to all items of this standard. 7 Scope of supply of products or sets
a) Machine;
b) Necessary accessories and wearing parts:
tools required for operation and repair;
8 Marking, packaging, storage and transportation
8.1 Labeling
8.1.1 Each product shall be labeled with a label, which shall comply with the provisions of GB/T13306 and include: name;
product number;
technical data;
factory number;
date of issue;
8.1.1 Product packaging, storage and transportation labels shall be selected correctly in accordance with the provisions of R19. 1.3 Transport packaging and delivery mark of GAT3R, 8.2 Packaging
2.1 Before product packaging, the external parts and plating should be treated with rust prevention. 82. For product export packaging, each packing box should be numbered. Technical safety and efficacy are in the first packaging box. 8.3 Storage
The output should be stored in a dry, unobstructed place to avoid moisture. The storage period exceeds any period. The product box should be checked before leaving the factory. If the product packaging does not meet the relevant regulations, the product should be repacked. 8.4 Transportation
When the product is transported and lifted, it should be lifted according to the product mark on the outer wall of the packaging box and placed gently to prevent it from falling. 8.5 When the product leaves the factory, the following documents must be submitted: 1) Product certificate
The number of product certificates shall comply with the provisions of GB 14436: b) Instructions for use
The end of the instruction manual shall comply with the provisions of GB 9969.1; c) Packing list,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.