Some standard content:
IC 55.200
Classification number: Y99
Registration number: 11402003
Light Industry Standard of the People's Republic of China
QB/T2570-2002
9B/T3688-1999
Labeling machine
Labeler
Published on 2002-12-27
National Economic and Trade Commission of the People's Republic of China Implemented on 2003-04-01www.bzxz.net
QB/T2570-2002
4 standard is a special standard ZBTY99035-1990 issued by the former Ministry of Light Industry. This standard was issued by the District Light Industry [1999] No. 112 document and the conversion standard number is 0B/3688-1999, which is unchanged: fast let. Revision content 1. Add three labels and four labels: performance indicators: the original standard performance indicators are mentioned; the definition of stop label, special rate, damage rate and stop label rate is added; the product reliability index is:
This standard is the national standard for wine and beverage machinery standardization technical changes! This standard is from: Dongfang Light Industry Machinery Co., Ltd. The main contributors: Zhang Shice, He Ziwen, Shui Huan Standard Bai Shichikou: The same as the original national economic and industry standard QB368-199 labeling machine 9TfKAoNnYKAca=
labeling machine
QB/T 2570 2002
This standard specifies the definition, classification, requirements, test and treatment, inspection specifications, marking, use instructions, packaging, transportation box, storage
small standard for small standard machines (hereinafter referred to as "products") that must be glued with paper or two smart international signatures on the round packaging of the customer. The equipment that can meet the product operation requirements and has corresponding standards will be used as a reference. 2 Normative references
The following clauses become the service clauses of this standard through the use of this standard. For any document with a date of application, the standard shall be changed directly after its approval (excluding the standard). The internal wear or reference version of this standard is not a training Ding tour, however: the number of dynamic according to this standard reached an agreement in the name of the good is the actual consultation of these transfer documents related to the stock analysis version: any period of the cited state document, its latest cost applies to this standard. GB3768-196 Determination of sound source shear rate level and surface 1 side network measurement of surface load or GRB4514-1996
GD5226.1-196 Machinery and equipment for industrial use Part: General technical provisions of this article G7718-1994 food you signed
non-heart product said the book general principles
GA 9969.1—1998
（1034-1989 Label standard for alcoholic beverages
GE/T13306-1991
GT13384-1992 Technical conditions for packaging of electric core productsG11453-1903 General technical requirements for light machineryBB:T 0018—2(00)
Packing capacity of alcoholic beverages
Acid packaging materials
QF 2112—1995
QB/T3562—1999
Additional standards for crown-shaped bottles
3 Specifications
The following specifications apply to this standard.
When the label is attached to the packaging container, the difference between the center of the damaged label and its theoretical position is within the specified range, which is the label. If there are multiple labels on the packaging container, the deviation of the positions of each label should be calculated according to the above definition, and they should all be within the specified range. 3.2
Labeling inspection
Technical requirements for labeling (single or multiple labels) The ratio of the number of packaging containers with labels to the total number of containers inspected. 3.3
Damage rate
During the labeling process, the percentage of the number of damaged labels on the labeling machine and the total number of labels consumed during the labeling inspection|| tt||QB/T2570—2002
Positive standard rate
In the packaging container being tested, the percentage of the total number of packaging devices tested in the whole tray is the percentage of the total number of packaging devices tested. 4 Classification
The types of products are divided into true soul testing machine and rotary sticking machine. 5 Requirements
5.1 Basic requirements
The product shall comply with the provisions of this standard and shall be tested through the prescribed procedures with the drawings and technical documents of the standard. 5.2 Working conditions
5.2.1 The standard packaging device type shall comply with the provisions of GB4544-1996.BR/T018-2000.QR2142—1995OB/T3562-1999
5.2.2 The standard bag shall comply with the provisions of GB7718—1904 and GB10344—[9B9]. 5.2.2.1 Quality of label paper
a) Body label: 7ng/mg/m*
b) Back label: 65g/m2-80g/
) Gold foil label: 25/m~40g/m.
5.2.2.2 Tensile strength of label paper
b) Dry pull: on a 15mm effective tape, the pull edge shall be no less than 24N, and metal box label shall be no less than 30N: 6% of the tensile strength. 5.2.2.3 Body label, head label and back label: Made of H plant fiber, the fiber direction should be parallel to the dot line, the paper surface cannot have a certain water absorption capacity. When the back of the paper leaks, it can be as shown in the figure: dot label back pattern
The limit shape of the label length
The correct ring space
The correct direction of the label after mixing with water
Figure 1 The correct fiber direction of the label paper and the curling direction after wetting HIKANYKA
5.2.2.4 The minimum allowable deviation of the label paper size is ±0.5μL: 5.2.3 Adhesive
QB/T 25702002
Labeling adhesive should have appropriate viscosity, appropriate thinness, fast drying speed, good water resistance and washing resistance, non-toxic and non-toxic. The performance should be stable in cyclic use, and the performance should not be significantly reduced in high-speed production. When the old bottle is washed, the label is easy to fall off.
5.2.4 Voltage code H380×(11≤%)V, frequency 50Hz.5.3 Usage label
5.3.1 The product should meet the rated production capacity. The damage rate, labeling rate, label reading rate and correct label rate of the gas meter and refrigerator are shown in 1.5.3.2
Body and room lamp
Capacity and capacity of the package,
Continental inspection,
Empty label. The soft
body cup, toilet
note mark must meet the following requirements.
)body mark, square mark, the price difference between the center of the mark and its position is ≤nb: capital mark: the center of the mark is compared with the position of the standard, the center of the mark is 3mmc)body mark, high mark, mark 4 fixed angle, the center of the mark is the difference between the center of the mark and its position. 5.3.3 The product is in normal operation, and the throat is not more than 8 products (A): 5. 4 Safety requirements
year altar, 2
other altar, back field
friend mark, treatment mark
54. There should be a safety crown, suitable for dozens of gas or two-pack products should be equipped with an integral safety door, the product circuit, the selection and operation of the motor single system unit to place their wiring and installation, double and consider the waterproof requirements. 5.4.2 The product should have a dot lock machine.
When there is a packaging container, the machine should automatically stop; a
6) When the packaging container is loose or stuck, the machine should automatically stop. 5.5 The quality requirements of the product, such as the machine board and parts assembly, should meet the requirements of GB/T14253-1993: 5.6 The gas system of the product should be smooth and free of leakage, and the pressure adjustment should be flexible and accurate. 5.7 The gas part should meet the requirements of GB/T5226.1-1996. The output and cam assembly should be reliable and free of conduction, etc., and the machine should be able to operate normally and safely. 5.9 Product reliability indicators
5.9.1 The maintenance period is about 50h.
Complete machine was manufactured in 2000011:
6 Test method
6.1 Determination of production capacity
After the product is properly turned, the number of packaging containers is continuously counted on the box bottle section behind the wheel. The measurement time is 0.5h. The production capacity is calculated according to formula (1). The result meets the requirements of 5.3.1. Q=
QB/T25702002
Wuhan:
Production capacity, bottle/h:
The number of packaging containers discharged from the front of the chamber is bottle,
6.2 Determination of damage rate of packaging containers
The measurement is carried out after the continuous operation of the production capacity is normal, which can be carried out in the same time as the measurement of production capacity. Test time 0.5h, count the number of damaged packaging contents and the number of damaged packaging containers in the test. The recovery formula (2) calculates the packaging incubator intake rate, which should meet the requirements of 5.3, 2.
Packing capacity damage rate, %:
-circular gas container teaching, bottle:
B-"input fairy according to the number of net containers, bottle
6.3 Labeling rate measurement
Production by continuous rotation to stop the normal operation plan, in the product second injection of oil take 00, after 10 can be line pull 1 bottle, a total of 200 bottles, from which no standard without label packaging device, report formula (3) to calculate the labeling rate, in accordance with 5.3.2 requirements.
Wu Zhong:
M.-label rate, %
C: : "invested in the second label benefit station label packaging total micro-count, tray. 6. 4 Determination of the rate of correctness
The product is tested during the production process. 10 bottles are taken from the production line, and 200 bottles are taken from the two consecutive 10m bottles, a total of 200 bottles are given. Formula 4) The rate of correctness should meet the requirements of 5.3.2. 200
Wu Zhong:
N—Normal rate, %:
The number of bottles of packaging containers for labeling. 6.5 Determination of the rate of damaged labels
After the product is delivered to the production station, the test is carried out for 5h. The number of damaged labels and the number of labels input at the time of the test are counted. Formula (5) The rate of damaged labels should meet the requirements of 5.3.2. P
Wu Zhong:
Damage label rate, %1
The number of damaged labels, Zhang:
5The total number of labels used when labeling the input packaging container, Zhang. 6. 6 Determination of noise
During the product idling test process, the noise level of the product shall be measured according to the provisions of GB3708=196, which shall meet the requirements of 4
TYY KANYKAa
QB/T25702002
5.3.3. The surface is also selected to form a flat surface with the reference body, and the measurement distance is 1: the position of the device is checked with reference to Figure C.5 in Appendix C of GB/T3768-1996. If the double-product item is not tested, the test shall be carried out. 6.7 Electrical performance test
In the product idling test, the provisions of GB/T 5226.1-1996 shall be followed and the requirements of 5.7 shall be met. 6.8 Idle running test
The running test is from low speed to high speed, from low speed to fixed speed: the running time is not less than 0.5h, and it shall meet the requirements of 5.1-5.6 and 5.8.
Inspection rules
7.1 Inspection classification
Product inspection is divided into output inspection and type inspection. 7.2 Factory Inspection
7.2.1 Factory Inspection Items
Inspect in accordance with the requirements of 5.3-5.8. 7.2.2 Judgment Rules
Products are inspected one by one by the Quality Inspection Department. After verification, they are sold to the factory: When leaving the factory, the product is marked with the standard number used: If there are unqualified items in the factory inspection, it is allowed to be re-inspected. If it still fails to meet the requirements after re-inspection, it is determined that the product is unqualified.
2.3 Type Inspection
7.3.1 When there is a problem, type inspection shall be carried out. a) The new product is tested and approved: b) After the product is produced, if the structure, new materials, and process have changed, it may affect the product performance. After the product is produced, it will be sold to the factory: G
! According to the test results, there are big differences between the last type inspection requirements and the national quality inspection agency’s inquiries. e.
Type inspection can be carried out at the same time as the production site.
7.3.2 Type inspection items
Under the conditions other than 5.21, other items other than those required by the standard shall be inspected (except 5.9). 7.3.3 Sampling
Read 20% of the batch order, but not the whole batch. The products for type inspection are selected from the qualified products of the factory inspection. 7.3.4 Judgment rules
If all items are qualified, the product is qualified. If the items do not meet the requirements, or if the product fails to meet the requirements after re-inspection, the batch of products shall be determined to be unqualified in the type inspection. When the determination of 6.6 Noise level and 6.7 Gas safety performance test fail, the batch of products shall be judged to be unqualified. Emergency inspection is not allowed.
B mark, instruction manual
8.1 Logo
Year of product manufacture. For the prominent Goldwind signboard specified by the manufacturer, the signboard complies with the provisions of GB13306-1991, including a) model and name:
b) Determined production capacity:
Installation overview:
d) Product weight:
Appearance:
QB/T2570—2002
Factory number and factory version
g) Manufacturer name
8.2 Instructions
The use of the machine should comply with the provisions of the product instruction manual. The content of the product instructions shall comply with the regulations of B91-998. 9 Packaging, transportation and storage 9.1 Packaging 9.1.1 The product packaging shall comply with the regulations of GB/T1331992 9.1.2 The following technical documents shall be required for the product when it leaves the factory. a) Product qualification certificate: b) Product instruction manual; e) Packing list: 9.2 Transportation: The product body or parts to be transported shall be transported by land and water. 9.3 Storage: The product shall be placed on a ventilated, dry and rain-proof indoor floor. After 6 months of storage, it shall be unpacked for inspection: rust, dead rot, paint and packaging shall be removed. TKAONY KAa-3. Type inspection
7.3.1 When there is a situation, type inspection shall be carried out. a) The new product is tested and approved for production; b) After the first production, if there is a change in structure, new materials, or process, it may affect the product performance; c) After the first production, if there is a change in structure, new materials, or process, it may affect the product performance; d ... e.
Type inspection can be carried out at the same time as the production site.
7.3.2 Type inspection items
Under the conditions other than 5.21, other items other than those required by the standard shall be inspected (except 5.9). 7.3.3 Sampling
Read 20% of the batch order, but not the whole batch. The products for type inspection are selected from the qualified products of the factory inspection. 7.3.4 Judgment rules
If all items are qualified, the product is qualified. If the items do not meet the requirements, or if the product fails to meet the requirements after re-inspection, the batch of products shall be determined to be unqualified in the type inspection. When the determination of 6.6 Noise level and 6.7 Gas safety performance test fail, the batch of products shall be judged to be unqualified. Emergency inspection is not allowed.
B mark, instruction manual
8.1 Logo
Year of product manufacture. For the prominent Goldwind signboard specified by the manufacturer, the signboard complies with the provisions of GB13306-1991, including a) model and name:
b) Determined production capacity:
Installation overview:
d) Product weight:
Appearance:
QB/T2570—2002
Factory number and factory version
g) Manufacturer name
8.2 Instructions
The use of the machine should comply with the provisions of the product instruction manual. The content of the product instructions shall comply with the regulations of B91-998. 9 Packaging, transportation and storage 9.1 Packaging 9.1.1 The product packaging shall comply with the regulations of GB/T1331992 9.1.2 The following technical documents shall be required for the product when it leaves the factory. a) Product qualification certificate: b) Product instruction manual; e) Packing list: 9.2 Transportation: The product body or parts to be transported shall be transported by land and water. 9.3 Storage: The product shall be placed on a ventilated, dry and rain-proof indoor floor. After 6 months of storage, it shall be unpacked for inspection: rust, dead rot, paint and packaging shall be removed. TKAONY KAa-3. Type inspection
7.3.1 When there is a situation, type inspection shall be carried out. a) The new product is tested and approved for production; b) After the first production, if there is a change in structure, new materials, or process, it may affect the product performance; c) After the first production, if there is a change in structure, new materials, or process, it may affect the product performance; d ... e.
Type inspection can be carried out at the same time as the production site.
7.3.2 Type inspection items
Under the conditions other than 5.21, other items other than those required by the standard shall be inspected (except 5.9). 7.3.3 Sampling
Read 20% of the batch order, but not the whole batch. The products for type inspection are selected from the qualified products of the factory inspection. 7.3.4 Judgment rules
If all items are qualified, the product is qualified. If the items do not meet the requirements, or if the product fails to meet the requirements after re-inspection, the batch of products shall be determined to be unqualified in the type inspection. When the determination of 6.6 Noise level and 6.7 Gas safety performance test fail, the batch of products shall be judged to be unqualified. Emergency inspection is not allowed.
B mark, instruction manual
8.1 Logo
Year of product manufacture. For the prominent Goldwind signboard specified by the manufacturer, the signboard complies with the provisions of GB13306-1991, including a) model and name:
b) Determined production capacity:
Installation overview:
d) Product weight:
Appearance:
QB/T2570—2002
Factory number and factory version
g) Manufacturer name
8.2 Instructions
The use of the machine should comply with the provisions of the product instruction manual. The content of the product instructions shall comply with the regulations of B91-998. 9 Packaging, transportation and storage 9.1 Packaging 9.1.1 The product packaging shall comply with the regulations of GB/T1331992 9.1.2 The following technical documents shall be required for the product when it leaves the factory. a) Product qualification certificate: b) Product instruction manual; e) Packing list: 9.2 Transportation: The product body or parts to be transported shall be transported by land and water. 9.3 Storage: The product shall be placed on a ventilated, dry and rain-proof indoor floor. After 6 months of storage, it shall be unpacked for inspection: rust, dead rot, paint and packaging shall be removed. TKAONY KAa-
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.