title>JB/T 8362-1996 Technical requirements for bevel gear quenching machines - JB/T 8362-1996 - Chinese standardNet - bzxz.net
Home > JB > JB/T 8362-1996 Technical requirements for bevel gear quenching machines
JB/T 8362-1996 Technical requirements for bevel gear quenching machines

Basic Information

Standard ID: JB/T 8362-1996

Standard Name: Technical requirements for bevel gear quenching machines

Chinese Name: 锥齿轮淬火机 技术条件

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1996-04-22

Date of Implementation:1996-07-01

standard classification number

Standard Classification Number:Machinery>>Metal Cutting Machine Tools>>J56 Gear and Thread Processing Machine Tools

associated standards

alternative situation:JB/GQ1112-87

Publication information

other information

Focal point unit:Tianjin Gear Machine Tool Research Institute

Publishing department:Tianjin Gear Machine Tool Research Institute

Introduction to standards:

This standard specifies the requirements for the manufacture and acceptance of bevel gear quenching machines. This standard is applicable to bevel gear quenching machines with a maximum workpiece diameter of 320~1250mm. JB/T 8362-1996 Technical conditions for bevel gear quenching machines JB/T8362-1996 Standard download decompression password: www.bzxz.net

Some standard content:

Mechanical Industry Standard of the People's Republic of China
JB/T 8362—96
Technical Conditions for Bevel Gear Quenching Machines
Issued on April 22, 1996
Ministry of Machinery Industry of the People's Republic of China
Implementation on October 1, 1996-01
Mechanical Industry Standard of the People's Republic of China
Gear quenching machine,
Technical parts
1 Subject content and applicable use
This standard specifies the requirements for the manufacture and assembly of sprocket quenching machines. This standard is applicable to cone-step wheel ignition machines with large workpiece diameters of 320~.1250m. 2 Reference standards
GB2891
GB35226
JT#4139
JB/GQ 1111
2H.150 003
ZB JSU C4
ZBn J50 008.?
ZBJOC1G
3 General requirements
Safety enterprise mark
General technical equipment
Electrical equipment of machine tools
Metal cutting machine tools
General technical conditions
Technical conditions for safety protection of chip cutting machine tools and machine tool accessories
Determination of noise
Metal primary cutting machine
Metal thick cutting machine tools
Metal pre-cutting machine tools
Measurement of sound pressure level
Technical conditions for passing the workpiece against cutting
Assembly code technical software
Metal pre-cutting machine tool hydraulic system general installation strip JB/T 8362-96
This standard is a supplement to the specific specifications of G906126.J50008.1, ZErJ>VU08. When accepting the acceptance method of this standard, it is necessary to conduct control inspection on the remaining rectification items specified in this standard. 4 Accessories and tools
4.1 The machine bed and electric feet should be supplied with a set of screws and pads for installation (the electric feet need to be nailed and screwed). 4.2 Special accessories can be supplied according to the agreement.
5 Full sanitation
5.1 The workbench! The lower die > forward or reverse movement, limit position or prevent the replacement of the insurance device 5.2 The machine must be equipped with a positive plate to prevent the coolant from flying Yao, the bed guide wheel and other parts that are easily damaged by dust or material, and there is no active stomach.
5.3 The following parts of the machine tool should have a safety interlock device: The door (or cover) of the machine tool electrical box is not closed. The machine will start the machine. Apply oil to the inner surface of the door (or cover) and check the outer surface of the door (ton benefit) in Figure 2-- of B2894. A warning sign; b. The dynamic smoothness of the moving parts The sequence of the system, the sequence of the system after the opening and closing, all have safety interlock devices; when the system power is not in the palace or a fault occurs, a warning signal or an emergency stop button should be issued, the port system of the old environment energy device, a force should be released or cut off the storage device for rest! : Power adjustment: d.www.bzxz.net
Approved by the Ministry of Machinery Industry on 22nd
1996-07-01Implementation
JBT36296
The workpiece is not moving in the three working cycles of the machine. E
5.4 According to the provisions of ZBJ50F4, the machine tool noise is inspected. The sound test of the machine should be carried out under the condition of the working cycle. The sound pressure level of the whole machine shall not exceed 8 (A),
5. The operating force of this series of machine tools is subject to the "not often used" requirement assessment 5.6 When accepting the machine tool according to this standard, it is necessary to simultaneously inspect the JI41 89 The remaining acceptance items that have not been fully integrated in this standard shall be inspected according to the acceptance items specified in standards such as GE5226 and 2ZBJ51016. 6 Machining and assembly
6.1 The machine tool bed, worktable, worktable bearing, oiled cylinder body, pressurized cylinder body and lower flange as the main castings shall be aged after roughing. The welded machine tool bed must be aged after welding. .2 The guide rails or slide bars between the machine tool bed and the worktable and the sliding pairs composed of them shall be wear-resistant. The eccentric wheel, oiled support and upper and lower plane cams shall be pre-grinded. 6.3 The following joints shall be assessed according to the requirements of the fixed joint surface: 8: The joint surface between the working part and the working self-supporting standard, b, the joint surface between the front column and the bed
The joint surface between the front column and the shaft body. e
6.4 The guide surfaces of the guide pairs of machine tools are assessed according to the requirements of the "Transfer Guide Model": 6.5 The clearance of the handle of the gear wheel with scale is not more than 1/2r6. Check the cleanliness of the machine tool according to the provisions of ZB.50003. Generally, it is checked by hand feeling method. The state of the oil in the oil tank (or oil tank) should not exceed 15C by using the quantitative method. m name/L. Machine tool idle running test
7.I Single action test
Single effect test should test the following moving parts. Each action should meet the delay requirements, H,
Workbench forward:
Die down,
Workbench backward:
Die up:
Machine tool workbench has some forward (backward) action, and it is also necessary to test the workbench point forward (backward) action. 2 Working cycle test
The working cycle test is carried out according to the requirements of Table 1 (cooling oil may not be injected). At the beginning of the test, all mechanisms of the machine tool should be completed. Table 1
When injecting oil
The amount of injection
The number of cycles (times)
8 Machine tool load test
8.1 This series of machines should be subjected to load test. The recommended commissioning number is shown in Table 8.2 The load test should be carried out continuously for 1 time
19--20
Diameter mm
>500--300
Large ring
Huan Guang Lin
1x151.x1c
5.5×104×12×1
9 Track bed accuracy inspection
JB/T 8362—96
Outside is the center of the tensile device!
Real rate
! Wood series machine tools - dividends work precision inspection. When necessary, according to the technical design should be carried out more. 9.2: Inspection according to I center Q1111
Blue time: Washing oil volume
First priority
Third independence
First safety
Second no
Third design
3 The repositioning accuracy of the machine tool workbench before entering the work should be measured seven times in a row, and the error is calculated by the maximum and minimum number of the number of protection effects, and the difference is shown in Table 3.
u, (-25
Additional Notes:
323--8:0
This standard was proposed by the Technical Committee for Standardization of Gear Machine Tools: Tianjin Gear Machine Research Institute was responsible for drafting this standard.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.