title>JB/T 5971-1992 Single-stage multi-vane vacuum pump - JB/T 5971-1992 - Chinese standardNet - bzxz.net
Home > JB > JB/T 5971-1992 Single-stage multi-vane vacuum pump
JB/T 5971-1992 Single-stage multi-vane vacuum pump

Basic Information

Standard ID: JB/T 5971-1992

Standard Name: Single-stage multi-vane vacuum pump

Chinese Name: 单级多旋片式真空泵

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1992-07-20

Date of Implementation:1993-01-01

standard classification number

Standard Classification Number:Machinery>>General Machinery and Equipment>>J78 Vacuum Technology and Equipment

associated standards

Publication information

other information

Focal point unit:National Vacuum Technology Standardization Technical Committee

Publishing department:National Vacuum Technology Standardization Technical Committee

Introduction to standards:

This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules and marking, packaging, storage, etc. of single-stage multi-vane vacuum pumps. This standard applies to single-stage multi-vane vacuum pumps. This standard does not apply to single-stage oil-sealed rotary vane vacuum pumps. JB/T 5971-1992 Single-stage multi-vane vacuum pumps JB/T5971-1992 Standard download decompression password: www.bzxz.net

Some standard content:

Mechanical Industry Standard of the People's Republic of China
JB/T5971-92
Single-stage multi-rotary vane vacuum pump
Published on July 20, 1992
Implementation by the Ministry of Machinery and Electronics Industry of the People's Republic of China on January 1, 1993
Mechanical Industry Standard of the People's Republic of China
Single-stage multi-rotary vane vacuum pump
1 Subject content and scope of application
JB/T5971-92
This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules and marking, packaging, storage, etc. of single-stage multi-rotary vane vacuum pumps. www.bzxz.net
This standard applies to single-stage multi-rotary vane vacuum pumps (hereinafter referred to as pumps), and does not apply to single-stage oil-sealed rotary vane vacuum pumps. Reference standards
GB3163
GB6306
GB7772
GB/T13306
GB/T13384
ZBJ78016
3 Terminology
Terms of vacuum technology
Performance test method of positive displacement vacuum pump
Noise measurement method of positive displacement vacuum pump
General technical conditions for packaging of electromechanical products
Vacuum pump model compilation method
The terms used in this standard shall comply with the provisions of GB3163. Type and basic parameters
4.1 Type
The pump is a single-stage multi-vane type.
4.2 Model
According to the provisions of ZBJ78016.
4.3 Basic parameters
Basic parameters shall comply with the following table,
XD-25
XD-100
XD-160
XD-250
Geometric pumping speed
Approved by the Ministry of Machinery and Electronics Industry on July 20, 1992 Limiting pressure
<2×102
Noise sound power level
Power consumption
Inlet inner diameter
Implemented on January 1, 1993
5 Technical requirements
JB/T597192
5.1 The pump shall comply with the requirements of this standard and be manufactured in accordance with the drawings and technical documents approved by the prescribed procedures. 5.2 The paint on the outside of the pump shall be smooth.
5.3 The ambient operating temperature of the pump is 5~40℃. 5.4 The ultimate pressure of the pump shall comply with the provisions of Table 1; the ultimate pressure is the pressure measured at the specified position on the test cover with an oil U-tube vacuum gauge. The pumping rate shall meet the requirements of Article 5.5 of this standard. 5.5 The pumping rate of the pump, measured at an inlet pressure of 7×10\Pa, shall not be less than 80% of its geometric pumping speed. 5.6 During normal operation, the maximum power consumption of the pump shall not exceed the power of the matching motor (except for instantaneous overload). When the pump is connected to the atmosphere at the air inlet, oil shall not be sprayed within 2 minutes: 5.7
When the pump is running at the ultimate pressure, its noise shall comply with the provisions of Table 1. 5.8
5.9 After parking, the restart shall not be hindered by oil return. The pump should not leak oil, and the water-cooled pump should not leak water. 5.10
The complete set of products should give detailed provisions for auxiliary machines, accessories and spare parts in the product manual. 5.11
On the premise that the user complies with the storage, use and installation rules of the pump, within one year from the date of shipment from the manufacturer, if the product is damaged or cannot operate normally due to poor manufacturing quality, the manufacturer shall be responsible for free repair or replacement for the user. Test methods and inspection rules
The test method of the pump shall be carried out in accordance with GB6306 and GB7772. 6.2 Each pump product must be inspected and qualified by the inspection department before it can leave the factory. 6.3 Pump product inspection is divided into factory inspection and type inspection: 6.3.1
Factory inspection items include:
Ultimate pressure;
Operation test for 2h.
Type inspection: Whenever a new product is developed or there is a major change in the design, process or material of the product, a type inspection shall be carried out. The items include: 6.3.2
Ultimate pressure;
Pumping speed;
Power consumption;
Noise;
Oil injection,
Type inspection 5% of each batch shall be sampled, but not less than two units. If it fails, double sampling shall be carried out. If it fails again, the batch of products shall be inspected one by one. Marking, packaging, storage
Each pump shall be nailed with a product nameplate in a conspicuous position. The type and size of the nameplate shall comply with the provisions of GB/T13306. The nameplate shall indicate the manufacturer's name;
Product model, name and number;
Product technical specifications;
Ultimate pressure, Pa; Pumping speed, m/h; Motor power, kW; Speed, min-; d. Year and month of manufacture.
7.2 Pumps are not allowed to be stored outdoors to avoid rust and damage. 7.3 Each pump should be accompanied by the following documents when it leaves the factory: a. Product certificate;
b. Packing list;
c. Product manual.
7.4 Packaging
Pump packaging should comply with the provisions of GB/T13384.
Additional instructions:
JB/T5971-92
This standard is proposed and managed by the National Vacuum Technology Standardization Technical Committee. This standard was drafted by the Shenyang Vacuum Technology Research Institute of the Ministry of Machinery and Electronics Industry. The main drafters of this standard are Zhang Shufan, Li Chunying and Zhang Chenlian. People's Republic of China
Mechanical Industry Standard
Single-stage multi-vane vacuum pump
JB/T 597192
Published by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry Printed by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry (PO Box 8144, Beijing 100081)
Copyright reserved
Format 880×1230
First edition in October 1992
Print run 0.001
No reproduction allowed
Sheet 3/8
Word count 6000
First printing in October 1992
Price 1.00 yuan
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.