HG 21607-1996 Special-shaped cylinder and head HG21607-1996 standard download decompression password: www.bzxz.net

Industry Standard of the People's Republic of China
HG 21607-96
Special-shaped Cylinders and End Caps
1996-11-27 Issued
199703-01
Ministry of Chemical Industry of the People's Republic of China
Document of the Ministry of Chemical Industry
Chemical Construction Development (1996) No. 814
Notice on Issuing Six Industry Standards Including "Glass Plate Liquid Level Meter"
To the Chemical Industry Departments (Bureaus, Companies) of all provinces, autonomous regions, municipalities directly under the Central Government and cities with independent planning status, and all relevant design units: The six standards including "Glass Plate Liquid Level Meter" organized by the Equipment Design Technology Center of the Ministry of Chemical Industry and edited by China Huanqiu Chemical Engineering Company have been approved as mandatory industry standards after review (see the attached table for the standard names and numbers), and will be implemented from March 1, 1997. At the same time, the original chemical standards HG51363~1370-80 and HG5-227-80 were abolished.
These six standards are managed by the Equipment Design Technology Center of the Ministry of Chemical Industry, and published and issued by the Ministry's Engineering Construction Standards Editing Center.
Appendix: Table of 6 industry standards including "Glass Plate Liquid Level Gauge" Ministry of Chemical Industry
November 27, 1996
Standard Name
Editor of 6 industry standards including "Glass Plate Liquid Level Gauge"
Standard series and technical requirements for glass plate liquid level gauge 2
Transparent glass plate liquid level gauge
Reflective glass plate liquid level gauge
Sight glass plate liquid level gauge
5 Standard series and technical requirements for glass tube liquid level gauge 6 Special-shaped cylinders and heads
China Huanqiu Chemical Engineering Corporation
China Huanqiu Chemical Engineering Corporation
China Huanqiu Chemical Engineering Corporation
China Huanqiu Chemical Engineering Corporation
China Huanqiu Chemical Engineering Corporation
Equipment Center of Ministry of Chemical Industry
HG 21588—95
HG 21589-95
HG 2159095
HG 21591--95
HG 21592—95
HG 21607--96
Industry Standard of the People's Republic of China
Special-shaped Cylinder Sleeve and End
HG 21607-96
Equipment Design Technology Center of the Ministry of Chemical Industry
Yixing Beihai Head Co., Ltd.
Editor:
Sixth Design Institute of the Ministry of Chemical Industry
Approval Department: Ministry of Chemical Industry March 1, 1997
Implementation Date:
Engineering Construction Standard Editing Center of the Ministry of Chemical Industry
1997 Beijing
Main Contents and Scope of Application
Cited Standards,
Symbol Explanation
Type and Basic Parameters| |tt||5.1 Nominal diameter
5.2 Height of straight edge
eettee
5.3 End trimming, beveling and thinning
Dimension and shape deviation
6.1 Tolerance of inner diameter and outer circumference
6.2 Difference between maximum and minimum inner diameter (out-of-roundness)····6.3 Tolerance of total depth·
6.4 Minimum thickness
6.5 Shape deviation
Technical requirements
8.1 Materials
8.2 Preparation of return materials*| |tt||8.3 Forming
8.4 Heat treatmentwwW.bzxz.Net
8.5 Edge trimming and groove processing
Inspection methods
9.1 Raw material inspection
9.2 Inspection of size and shape deviations
9.3 Weld inspection
9.4 Groove inspection
9.5 Appearance and surface inspection
（1）
（2）
（3）
（4）
In physical blood
（7）
(7)
(9)
(9)
(9)
Inspection rules
11.1 Marking instructions
·11.2 Marking examples
12 Quality certification documents
13 Marking, packaging and transportation
Preparation instructions
1 Main contents and applicable scope
This standard specifies the types, parameters, technical requirements, inspection methods and marking, packaging, transportation and other contents of stamping and spinning special-shaped cylinders and heads for welded containers. This standard applies to special-shaped cylinders and heads for steel welded containers (hereinafter referred to as "heads"). 2
GB9019
JB2536
HG 20581
《Steel Pressure Vessels》
Cited Standards
《Nominal Diameter of Pressure Vessels》
《Painting, Packaging and Transportation of Pressure Vessels》《Provisions for Material Selection of Steel Chemical Vessels》
《Procedures for Inspection of Steel Rulers》
《Procedures for Inspection of Steel Tape Measures》
Symbol Explanation (Units are all mm except for angles) 3
D——Inner diameter of the end cap (large end),
d:-Inner diameter of the end cap (small end)
H Total depth (or height) of the head;
h—Height of the straight edge of the head:
h:-Deepness of the curved surface of the head;
hs—Height of the straight edge of the head (small end);
R—Inner radius of the spherical part of the head;
r—Inner radius of the transition zone of the head (large end);r—Inner radius of the transition zone of the head (small end);-Nominal thickness of the head:
aa—Design thickness of the head;
—Vertex angle of the cone shell (degrees).
Type and basic parameters
4.0.1 The type, parameters, cross-sectional shape and code of the head shall be in accordance with the provisions of Table 4.0.1. If the type and parameters other than those in Table 4.0.1 are required, the manufacturer shall be consulted. 4.0.2 The nominal diameter and straight edge height h of the head (except LTH and LEH) shall comply with the provisions of 5.1 and 5.2 of this standard.
Type name
Shallow dish
Extended straight
edge shallow dish
shaped head
Extended straight
edge elliptical
shaped head
Folded edge cone
shaped head
h: 0. 194D;
r= 0. 1D:
hi=0.194D
hSee Table 4.0.2
D/2h;—2
hSee Table 4.0.2
α-120°150°
d:≥300
D:≥800
Dimensions to be noted
Di, o
D, on
D:ondiα
Type name
Reducing section
(large and small
end fold
conical seal
flow guide
(for heat exchanger)
eccentric circle
convex bottom seal
cross-sectional shape
continued table 4.0.1
dimensions to be noted
when ordering
α=60°90°
di≥400
CH--2 Di≥800
α= 60°, 90°
di≥400
D:≥800
α30°
di≥300
r,=0. 1d;
r= 0. 1D:
r≥38
=50, 75, 100
Di.oa.disa
Diondi
Di.di.on, rH
Type name
Bell mouth
Section shape
Note: If the purchaser places an order based on the designed thickness, it should be stated. True edge height of extended straight-side head
450~800
di≥150
r≥38
Continued Table 4.0.1
Dimensions to be noted
when ordering
Di.diaarH
=50, 75100
900~1400
≥1500
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.