This standard specifies the criteria for preventing accidents when using agricultural and forestry tractors and machinery and the reasonable parameters that should be achieved when designing tractors to ensure the personal safety of drivers and personnel performing normal operations and maintenance. This standard applies to agricultural and forestry tractors and machinery. GB/T 15369-2004 Safety Technical Requirements for Agricultural and Forestry Tractors and Machinery Part 3: Tractors GB/T15369-2004 Standard Download Decompression Password: www.bzxz.net

1C5.55.060.10
National Standard of the People's Republic of China
GB/T 15369-—2004/ISO4254-3:1992 Recommended by G3/Door: 153591994
Safety Technical Requirements
Tractors and machinery for agriculture and forestry
Part 3: Tractors
Trarturers and machinery for agriculture and forestry-Technical means fur ensuring safe -Part 3: Tractors(ISO4254-3+1992,11)T
2004-05-08 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Administration of Standardization of the People's Republic of China
2004-10-01 Implementation
CR/T 15359—2004/TSO 4254-3:1992 This standard is equivalent to 1042543:12 Agricultural machinery and equipment - Part 3: Technical requirements for agricultural machinery and equipment - Part 3: Tractors. This standard is a revision of 6169-1 Agricultural machinery and equipment - Part 3: Technical requirements for agricultural machinery and equipment - Part 3: Tractors. When revising, in addition to making changes to the material, the standard 1 is changed from a mandatory standard to a standard. This standard is issued by the National Technical Committee for Standardization of Tractors of the Chinese Machinery Industry. The drafting unit of this standard is Luoyang Tractor Research Institute. The drafters of this standard are Shang Xiangjue and Han Haixiao. The previous versions of this standard are: CB156H9, Scope, CD/T153 69—2004/1SO4254-31992 Safety technical requirements for agricultural and forestry tractors and machinery Part 3: Tractors
This standard specifies the criteria for the total external accidents that occur before and after the use of agricultural and forestry tractors and machinery and the reasonable costs to be achieved by the tractor state to ensure the personal safety of drivers and personnel performing normal operations and maintenance. This standard is used for "Agricultural and forestry tractor machinery 2 Normative references
Many of the following documents have become standard clauses through the use of this standard. For any formal referenced documents, all subsequent transfer modifications (not including internal safety) or static conclusions shall not apply: This standard, however, contains the six standards that have been agreed upon by the parties to the study and whether these two items can be reversibly used. For any referenced document, the latest version shall apply to this standard: GB/T1593.11996 Agricultural grab-type Hella machine mounted three-point product hanging bar Part 1, 2, 3 and - categories: cgIS7501.002
G3/6239-2004 Agricultural bottle inspection machine driving room door 1 tight read two and each member position size (15) 1252, 1S52TTTWww.bzxZ.net
G/TS1H Agricultural and forestry tractors and machinery, grass bad that Yi power Kai machinery missing reverse book compilation hot purchase ( H4C2601.e415023633:19963
G:05.1 Table of safety technical requirements for tractor engines and machinery, etc. Part 1, Standard (G10.195.1-20)1, 1S0) 4254--198)
【T/-19142003 Agricultural wheeled push-pull machine front-end installation part 1, effective Wanweng shaft and one-point hanging installation supervision (1SS:52-1.1498.TT)T
3 Safety requirements
3. 1 Suspension installation
3.1.1 Through the two lifting rods, the center of the load-bearing half and the towing control machine body are changed. In each position within the lifting process range (see year), the moving parts maintain a safe degree of 2It. If the cutting angle between the parts is changed within the range, the minimum clearance is maintained at 25m or the minimum clearance is 35 (see medical 2).a) The lifting line is the moving lifting circle, the upper and lower ends are U.1n, and the net distance between people and B is the lower base point A, for the lower emergency connection (T/-1593.1-159h in Table 2 Regulations: For the front base installation, the proposed height position shall be in accordance with the provisions of the 5th order of 3/11656200S. The base height position shall be in accordance with the national strength improvement range in March. 1) In the process of lifting, the surface of the lifting part shall be kept at a minimum safety distance of 25m2 from the adjacent components. 2. When installing the five-belt quick-acting device, the operator shall not only stand between the towing machine and the machine, but also avoid the use within the range of 230mm below the core point. 1.1. Note: 14. When the belt is a hanging device with a quick connection, the lower tire model is in accordance with the label. 3.1.3. The total column device probe longitudinal mechanism
3. 1. 3. 1 The main operating handles shall be properly arranged or protected on the vehicle and the technical connection so that the operator cannot touch them when operating the machine: GB/T15359-2C04/TSO4254-3:1992 3.1.3.2 Installation of operating handles Figure 2 is a schematic diagram of the installation of external operating systems. The operator should be able to operate them at the installation level, such as installing an external lifting handle or an auxiliary handle on the inside of the vehicle. There are two ways to operate the external operating handle: Type: a For each exploration, the limit of the amount of movement of the next push point is 0% m: small) The original exploration function of the vehicle is missing (for the expansion worker to eliminate the first, the next box transportation head automatically stops 3.1.3.3 side wheel (track: the main operating handle of the tractor (the main auxiliary puller) should be installed with a pulling handle to make the cat pass through the virtual mark point and the blood level before the dance, Note: The standard pulling effect is not great. The table of other five forms of the machine 3.1.3.4
is allowed to be filled with at least the same effect as 3.1.3.1~3.1.3.3. 3.2 Driver's work position
3.1 The driver is in the hand law (use less 3 times and the foot law and length, there is no single plan and squeeze. Special tractor excavator is designed according to the heat setting of .2.2. This must avoid the current setting of T "[. 2
Special area A
Figure 3 Driving individual reach area
GB/T15369-2004/ISO 4254-3:1992 single type is mm
and the damage point
3.2.2 Driving fee and area are divided into sphere 4 and see Figure 3. The center of the ball is 0ttr: in front of the driving mark and 58mm above the spherical half of the reach area is 550mm, the reach scale sphere radius is 1030mm55?m between the area in the reach area 4, the small space between the control mechanisms and between them and other adjacent parts is 12Un1E: in the reach area The minimum clearance should be 25mm: In the above extension area, the cabinet section component is called the standard angle for the wheel (track) gauge tractor. After the screw drop mark, the cross-section diagnosis surface must be vertically formed into a 5-point surface. After the cross-section, the above-mentioned dangerous parts are no longer used (see Figure ·). There should be a new danger point.
Network residual punctuation
Figure 4 Narrow wheel gauge tractor driving load and text
GH/T 15369-2004/ISO 4254-3:19923. 3.3.1 The access to the driver's seat shall comply with the requirements of (1/T6218-20G4). The driver shall be able to stop or hold the vehicle. If there are protruding parts (such as pedals) in the driver's station, the driver's feet can be placed near these parts, either in front, behind or behind. The above requirements shall be applied to the remaining seats of the Ding transport type (see Figure 5). In addition, from the front edge of the passenger seat, there is a dangerous area below the half-light body of the 8U0m half-demand body. Protection measures should be taken to avoid the dangerous components in the area 5, such as the extension of the front edge of the seat and the upper part of the circle as the center, so as to ensure the safety of the single female seat. ||Figure 5 Passenger and area
Standard: According to the provisions of the relevant law, the production base does not produce additional seats, 3.3.2 The exhaust pipe (whether it is a card or a self-track) of the tractor should be arranged reasonably. The horizontal stomach should be safe, so that the driver will not be directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel. The exhaust pipe outlet is arranged to prevent the personnel from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel. The exhaust pipe outlet should be ... from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel from being directly exposed to the burning components when working. Otherwise, the heating components should be raised to protect the personnel from being directly exposed to the burning components when working.The instruction card also includes the installation, use and maintenance of various accessories and options.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.