This standard specifies the requirements, sampling, identification content and identification rules for the use identification of dangerous goods packages for road transport, except for Class 2, Class 6, Item 6.2 and Class 7 in Chapter 4 of GB19269.1-2003. This standard applies to the use identification of dangerous goods packages for road transport, except for Class 2, Class 6, Item 6.2 and Class 7 as specified in Chapter 4 of GB19269.1-2003. This standard does not apply to pressure receptacles, packages with a net weight greater than 400kg, and packages with a volume greater than 450L. GB 19269.3-2003 Safety Specifications for Inspection of Dangerous Goods Packages for Road Transport Use Identification GB19269.3-2003 Standard Download Decompression Password: www.bzxz.net

Chapter 4, 6 and 7 of this standard are mandatory, and the rest are recommended. GB19269.3--2003
This standard is one of a series of standards for the inspection of dangerous goods for highway transportation. It is used in conjunction with the two standards of the general rules for inspection of dangerous goods for highway transportation and the safety rules for inspection of dangerous goods for highway transportation. The consistency of this standard with the revised version of the 12th edition of the National Regulations on the Transportation of Dangerous Goods and the International Highway Transportation of Dangerous Goods is non-variable. Its technical contents are completely consistent with the above regulations and provisions. The standard text format has been revised according to GB/T1.1-20CC. The content of this standard A, B and performance data are consistent with the content of this standard. This standard was proposed and approved by the National Technical Committee for the Management of Hazardous Chemicals (SA Center) on 25th. The responsible units for the development of this standard are: the National Institute of Standards and Technology for the Management of Hazardous Chemicals, the Highway Research Institute of the Ministry of Communications, the National Institute of Standards and Technology for the Management of Hazardous Chemicals, the Jiangsu Provincial Institute of Standards and Technology for the Management of Hazardous Chemicals, the Tianjin Entry-Exit Inspection and Quarantine Bureau, the Beijing Entry-Exit Inspection and Quarantine Bureau, etc. This standard is formulated for the first time.
1 Scope
Inspection, safety specifications and identification of packages for dangerous goods transported by road
GB19269.3—2003
This standard specifies the requirements, specifications, identification contents and identification of packages for dangerous goods transported by road other than Class 2, Item 6.2 of Class 6 and Class 7 in Chapter 4 of GB19269.1-2003. This standard is applicable to the identification of packages for dangerous goods transported by road other than Class 2, Item 6.2 of Class 6 and Class 7 as specified in Chapter 4 of GB11259.1-3603.
This standard is not applicable to packages with a net weight of less than 1 kg and a volume of more than 450 kg. 2 Normative referenced documents
The clauses in the following documents become the clauses of this standard through their reference in this standard. For any referenced documents with a sufficient indication and date, all subsequent amendments (excluding errors) or customization are not applicable: This standard, however, contains the latest versions of these documents that are used when the parties reach an agreement on this standard. For any referenced documents without a date, their latest versions are applicable to this standard. CB/T2828 Batch inspection, random sampling, ascending order, no sampling table CB1925:-2003 General rules for safety inspection of packaging of dangerous goods for road transportation GB19260.2--2003 General rules for safety inspection of packaging of dangerous goods for road transportation 3 Terms and definitions
The technical definitions established in GR1S2G9.1-2005 apply to this standard. 4 Requirements 4.1 General requirements 4.1.1 The embossed, printed or pasted marks, logos and labels on the exterior of the package should be accurate, clear and firm and comply with the requirements of GB16U-2000. The outer surface of the package should be clean. Residue, contamination or leakage should be minimized. 4.1.2 The selected container should be compatible with the properties of the dangerous goods to be transported and its performance should comply with the provisions of GB1025.1-2000 and GB1926S.2200. 4.1.3 The packing category of the container should be equal to or higher than the packing category required for the dangerous goods. 4.1.4 In the following cases, a classification and grading hazard characteristic inspection report (see Appendix A for example) shall be provided: a) The first production or not listed: b) The first logical import or export: c) It is necessary to pay attention to the following: if the reported contents do not match the actual contents, etc. 4.1.5 For the first use, a single-material packaging container or inner layer of the container or inner layer of the container shall provide a report of chemical compatibility test for more than 6 months (example H); 4.1.6 The net load of a single package of hazardous goods shall not exceed the weight specified in the United Nations International Convention on the Suitability of the Transport of Dangerous Goods. 4.1.7 For low-volume hazardous goods, the volume of the container shall be less than 98% of the total volume of the container. For goods with a large expansion coefficient, the required volume of the container shall be determined based on the total volume of the container. Solid dangerous goods shall be filled to less than 10% of the container volume. 1
CU 19269.3—2003
4.1.B When shielding or inert gas is used to protect dangerous goods, the shielding or inert gas shall effectively protect the safety of dangerous goods. 4.1.9 Dangerous goods shall not leak out of the packaging container and the inside and outside of the packaging container. 4.1.10 Dangerous goods and containers connected with them shall not have any chemical reaction that affects the strength of the container. 4.1.2 The attached materials shall not react with the dangerous goods to form dangerous chemical reactions, and the inner container shall be able to completely absorb and retain all dangerous goods when it is sealed, so as not to cause the empty materials to come out of the outer packaging container. 4.1.12 Shockproof and cushioning materials shall not react with the dangerous goods to reduce their resistance to chemical reactions, and there shall be enough filling materials to prevent the inner container from moving.
4.2 Special requirements
4.2.1 Requirements for precision and precision containers
4.2.1.1 For closed barrels, the large and small closure screws should be tightly matched and equipped with appropriate sealing rings. The tightening process should meet the sealing requirements.
4.2.1.2 Open cans should be equipped with appropriate sealing patterns, regardless of the form of the door, and should meet the sealing requirements. Therefore, they should be locked with pins.
4.2.2 Requirements for box containers
4.2.2.1 Wooden boxes and fiberboard boxes should be nailed firmly when nailed, and nails should not be protruding. Avoid the calcium in the container and add a seal to prevent any chemical reaction or physical change with the contents. The packaging tape should be tightly signed and sold. 4.2.2.2 The paper should be intact and sealed. The sealing surface should be smooth and the whole body should be tightened. 4.2.3 Requirements for this type of container
4.2.3.1 When the outer container is connected through the chain, the outer container of the inner bag shall not be folded more than 0mm. The chain can be stretched and tied with more than 5 stitches. The chain strength should ensure that the contents do not leak out and do not reduce the sealing strength. The outer chain should be sealed to ensure that there is no leakage of contents.
4.2.3.2 When sealing the inner bag, no matter whether it is sealed by tying, standing or other methods, it must ensure that the contents are sealed. 4.2.3.3 When sealing with a single tie, the gas in the bag should be discharged. The mouth should be tied with a rope twice, tied with a knot, then folded down and tied twice, and tied tightly. If the layers are stable, they should be layered according to this method. 4.2.3.4 Adhesion should be done in pairs to discharge the gas in the food. No holes are allowed to exist due to the poor adhesion. If the layers are double-sided, they should be bonded separately. 4.2.4 Requirements for containers containing food
When the food is put into the container, the seal must comply with the requirements of the roll seal, and the airtight seal must comply with the requirements of 4.2.4.1 [
].
4.2.4.2 For packaging with fragile contents (such as glass, etc.), the outer packaging shall comply with Class 1 packaging. 4.2.4.3 The materials shall comply with the requirements of 1.1.11 of this standard. 4.2.4.4 If the outer container is not leakproof or waterproof, a leakproof liner or inner container must be used. 5 Sampling
5.1 Inspection batch
The packaging with the same raw material seal and the same structure as the same production process is an inspection batch. 5.2 Sampling rules
The normal inspection is carried out according to GB/T 282. 3 Sampling quantity
The number of samples to be taken is shown in Table 1,
Appraisal range
16--25
93~15u
151--28:
501--1269
1221---3200
3 m7~-10 G:
Table sample replacement number
GB1929.3--2003
Based on the effective standard)
6.1 Briefly check whether the packaging of dangerous goods transported from one end to another meets the requirements of 4.1.1, 6.1.8 and 4.1.9. 6.2 Check whether the selected packaging is suitable for the dangerous goods for road transport according to the relevant provisions of GB1969.1-2003 and GB19259.2-2003; whether the color of the container is consistent with the category of the whole package, and whether there is a corresponding performance test report. 3. For the dangerous goods packaging for road transport, check whether it has the corresponding classification and hazard characteristics test report issued by the national quality department or the testing agency recognized by the national quality inspection department. 5.4 Check whether the road transport dangerous goods are suitable for road transport in accordance with the requirements of 4.1.5. 5.5 Check whether the replacement period of the liquid dangerous goods for road transport meets the requirements of 1.6. Extract the reduced volume of the dangerous goods for analysis and use as a gas to measure the gas content, and test whether the dangerous goods contain contaminants or gases according to the standards of the various types of dangerous goods. 6.7 Check whether the packaging, attached materials, pressure-sensitive materials, paper, and other packaging additional materials used for dangerous goods have chemical reactions that affect their use. 8. Check whether the packaging is in compliance with the provisions of GB11265.1-2013. 6.9 Check whether the sealing of the container meets the requirements of 4.2.3, 6.10 Check the requirements of 4.2.2 of the container layers of the box type, 6.11 Check whether the sealing of the inner container meets the requirements of GB19239.1200, and the outer container of the inner container is 1 container. The adsorbent material must comply with the provisions of 4.1.11, B.12 check whether the compartment type meets the requirements of 4.2.1 or not. Environmental rules
7.1, the enterprise using dangerous goods packaging should ensure that the dangerous goods packaging used for highway transportation meets the requirements of the standards, and shall be identified by the relevant inspection department. The user of hazardous waste goods shall follow the provisions of the standards and accept and inspect the hazardous waste in pieces.
7.2 The pieces of dangerous goods transported by highway transportation shall be identified in batches, and the order pallet shall be regarded as a batch, but the large quantity shall not exceed the maximum batch specified in 5.1.
819269.32003
7.3 The validity period of the inspection report should be calculated from the date of delivery of the dangerous goods. The validity period of the inspection report for Class A dangerous goods and packages with dangerous substances is no more than 6 months. The validity period of the inspection report for other dangerous goods is no more than 1 year, but this validity period cannot exceed the validity period of the performance inspection report. .4 Formulate rules: If there is an unqualified product, the batch of dangerous goods packages is not suitable for public transportation. After the above items are qualified, the inspection report (refer to the appendix) 7.5 Unqualified batch processing: After rework or removal of unqualified packages, the next inspection is not strict. 7.6 The qualified packages are not allowed to be submitted to the highway transportation auxiliary. Unless they are qualified again.啊景
(Material Appendix]
Classification, grading of hazardous characteristics inspection report example Classification, grading of hazardous characteristics inspection report format Table 21. Table 4, 1 Classification, grading of hazardous characteristics inspection report example (name of inspection agency)
Classification, grading of hazardous characteristics inspection report
Applicant,
Special test requirements
According to the United Nations manual on inspection materials and testing and standardization
Inspection order: hazardous goods classification, light level characteristics, basic 1. Clinical test of properties for use
2. External test
3. Gas test
Compliance:
GR19269.3—2003
Number of samples:
CH19269.3—2003
4. General plant inspection
6. Oxidation test
7. Elemental test and identification
8. Severity test and identification
9. Other hazardous characteristics
Table A. 1 (United>
F-, combined
Formal total name:
Joint code:
Dangerous goods number measurement:
Packing category
Packaging method,
Wuhan generally does not use portable augmented transport. Fire left method:
9CASCODE
10TCSCCODE
Packing mark
Excuse transportation service selection,
13Exit handling:
Capsule A. 1 (Continued)
Construction and modification to carry out 6 months of compatibility test on the packaging content, inspection personnel,
Note, 1 North laboratory draft this report is valid.
2 This copy of the report is invalid,
3 This batch of approval
date is valid,
Inspection of the whole machine:
GB19269.3—2003
CB 192E9.3—2003
(Informative Appendix)
Chemical compatibility test acid inhibition report example
Chemical compatibility test report format see Table B.1 Table R.1 Chemical compatibility test report format
Chemical cabinet storage test frequency
Packaging content use Sichuan year
Packaging table content production unit
Packaging customer and other operators and
ancestor When the goods are transported to the designated place, the goods are transported to the designated place according to the requirements of the dangerous goods. The dangerous goods are described in the following table: Dangerous goods packaging rules: Sealing person: Inspection person: Municipal people, Wearing number: Use identification technology report form 1. (Informative Appendix) Quick identification report Example
Table C, 1 Inspection and appraisal report format
XX document name of dangerous goods inspection machine
Selected packaging container for dangerous goods complete report to the provincial applicant
Packing container name and specification:
Back packaging type
Equipment device function
Qualification inspection number
Transportation method
Name of dangerous goods inspection
Dangerous goods Physical state
Dangerous quantity
Is the date of packaging of dangerous goods
Inspection image
Please press
Basic word,
Borrowing date
Applicable quantity
Technical modification
Chinese?
GB19269.3—2093
Self-packaging natural material registration number:
Dangerous goods identification!
United Nations number
Applicable to dangerous goods
Check the person
H date:
Net quantity of a single piece
Find the sellerOxidizing property test and adjustment
VII. Elemental property test and identification
VIII. Severity test and identification
IX. Other hazardous characteristics
Table A.1 (Unit>
F-, summary
Formal total input name:
Joint code:
Dangerous goods number measurement:
Packing category
Packaging method,
Wuhan generally does not use portable augmented transport. Fire left method:
9CASCODE
10TCSCCODE
Packing mark
Excuse transportation service selection,
13Exit handling:
Capsule A.1 (Continued)
The packaging capacity is subject to 6 months of inspection and testing. Inspection personnel,
Note, 1. This report is only valid if it is drafted by the laboratory.
2. The copy of this report is invalid.
3. This batch of approval is valid on the date of
,
Inspection of the whole machine:
GB19269.3—2003
CB 192E9.3—2003
(Informative Appendix)
Example of chemical compatibility test report
For the format of chemical compatibility test report, see Table B.1 Table R.1 For the format of chemical compatibility test report
Chemical cabinet storage test frequency batch
Package to use Sichuan year position
Package table content still strict unit
Packaging customers and other operations and
Ancestor travel class thank you for the material
Class material Production degree
In the United States
Specification
Specification of dangerous goods characteristics
Dangerous goods packaging rules
Sealing person:
Inspector:
City,bzxZ.net
Trade number:
Use identification technology report format table 1.
(Informative Appendix)
Quick identification report example
Table C, 1 Check the identification report format
XX document insurance inspection machine name Name
The selected packaging container for dangerous goods shall be reported to the applicant
Name and specification of packaging container:
Type of packaging
Equipment of equipment
Qualification inspection number
Transportation method
Name of dangerous goods
Status of dangerous goods
Quantity of dangerous goods
Date of packaging of dangerous goods
Inspection image
Please click
Basic word,
Bakery single period
Applicable quantity
Technical modification
Chinese?
GB19269.3-2093
Self-packed natural goods mark and number:
Dangerous goods identification!
United Nations number
Risk goods exemption
Check the end person
H period:
Single piece net
Number
Find the sellerOxidizing property test and adjustment
VII. Elemental property test and identification
VIII. Severity test and identification
IX. Other hazardous characteristics
Table A.1 (Unit>
F-, summary
Formal total input name:
Joint code:
Dangerous goods number measurement:
Packing category
Packaging method,
Wuhan generally does not use portable augmented transport. Fire left method:
9CASCODE
10TCSCCODE
Packing mark
Excuse transportation service selection,
13Exit handling:
Capsule A.1 (Continued)
The packaging capacity is subject to 6 months of inspection and testing. Inspection personnel,
Note, 1. This report is only valid if it is drafted by the laboratory.
2. The copy of this report is invalid.
3. This batch of approval is valid on the date of
,
Inspection of the whole machine:
GB19269.3—2003
CB 192E9.3—2003
(Informative Appendix)
Example of chemical compatibility test report
For the format of chemical compatibility test report, see Table B.1 Table R.1 For the format of chemical compatibility test report
Chemical cabinet storage test frequency batch
Package to use Sichuan year position
Package table content still strict unit
Packaging customers and other operations and
Ancestor travel class thank you for the material
Class material Production degree
In the United States
Specification
Specification of dangerous goods characteristics
Dangerous goods packaging rules
Sealing person:
Inspector:
City,
Trade number:
Use identification technology report format table 1.
(Informative Appendix)
Quick identification report example
Table C, 1 Check the identification report format
XX document insurance inspection machine name Name
The selected packaging container for dangerous goods shall be reported to the applicant
Name and specification of packaging container:
Type of packaging
Equipment of equipment
Qualification inspection number
Transportation method
Name of dangerous goods
Status of dangerous goods
Quantity of dangerous goods
Date of packaging of dangerous goods
Inspection image
Please click
Basic word,
Bakery single period
Applicable quantity
Technical modification
Chinese?
GB19269.3-2093
Self-packed natural goods mark and number:
Dangerous goods identification!
United Nations number
Risk goods exemption
Check the end person
H period:
Single piece net
Number
Find the seller
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.