This standard specifies the types and basic parameters of general-purpose four-column hydraulic presses. This standard applies to newly designed general-purpose four-column hydraulic presses. JB/T 9957.2-1999 Four-column hydraulic press types and basic parameters JB/T9957.2-1999 Standard download decompression password: www.bzxz.net
Some standard content:
[CS 25.120.10 Machinery Industry Standard of the People's Republic of China JB/T9957.2-1999 Four-column hydraulic press 1999-05-14 Issued Type and basic parameters 20-00-01-01 Implementation National Bureau of Machinery Industry JB/T9957.2—1999 This standard is a revision of ZB162020-99 Four-sample filter press type and basic parameters". This standard is basically consistent with the technical content of ZBJ62020-8, and has only been re-edited according to relevant regulations. This standard will be implemented on January 1, 2000, and will replace ZBJ62020-89 from the date of implementation. Appendix A of this standard is the appendix of the standard. This standard was proposed and coordinated by the National Technical Committee for Standardization of Forging Machinery. The responsible drafting units of this standard are: Jinan Zhudao Forging Machinery Research Institute, Shenyang Forging Machinery Factory. This standard was first issued in April 1976. Machinery Industry Standard of the People's Republic of China Type and Basic Parameters Four-column hydraulic press This standard specifies the type and basic parameters of a four-column hydraulic press for a single purpose. This standard is applicable to newly designed four-control hydraulic presses for a single purpose. 2 Referenced Standards JB/T9957.2-1999 Generation 2H16220KybzxZ.net The following standards contain provisions that are incorporated by reference in this standard: When this standard is published, the standard version is valid. All standards may be revised, and the parties using this standard should explore the possibility of using the latest version of the underlined standard. IRT3843-1999 Press is tightly connected and uses a rod, the distribution form and size of the holes 3 Four-column hydraulic press structure The most commonly used four-column hydraulic press can be divided into two types according to its applicable process requirements, without a device and with a device, as shown in Figure 2. 4 Four-column hydraulic press main parameters and basic parameters 4. The main parameters of the four-column hydraulic press are nominal force. 42 The basic parameters of the four-column hydraulic press should comply with the provisions of Table 1: 4. The distribution form and size of the baffles and supports used to fasten the mirror on the workbench and the sliding surface of the four-column hydraulic press should comply with the provisions of Appendix A (the standard). Approved by the State Administration of Machinery Industry on May 14, 1999, and January 1, 2000 Implementation JB/T9957.2—1999 No item H! Installation of column hydraulic press Figure 2 has an item to install a four-column hydraulic press Investment decision stroke 5 Lift [high seat" Pressure avoidance polar Air travel Work 4 and have teaching ideas Three in × front bottom Public you point correct Item and for production Open height ! Speed maintenance Space difference down 1N surface effective scale Mountain force P Forward product 5 1899522-1999 Table 1 Basic parameters of four-way liquid machine 500×500 152[11320 9004900 [:001400 4 : isn | 0O [250-1250 2500×1500 630-634 120[120 220-16(K) 1600×160K 3150x2G0G 125× 1250 25G080U 20c.o::40n 3150>2U0! 1 Heavy bottom dynamic life correction, installation, year of production technology requirements, 2 Chaos resistance recommended Ding Lingjin plus 1, shallow forming, cold extrusion and other 1 requirements 3T. Speedometer to test the speed under full load. 3 JB/T9957,7—J999 Appendix A (Standard Appendix) Distribution form and size of grooves and holes for fastening dies of four-column hydraulic presses 411000kN and below The T-shaped joints on the working surface and the lower plane of the slide of the four-column hydraulic press are distributed diagonally. The distribution form should be derived from Figure A1 The T-slots on the workbench and the lower plane of the slider of the four-stage pressure relief machine of 1600-10000 kN are distributed in parallel. The distribution form and spacing should comply with the provisions of Figure A2 and Table A! A3 The form and size of the T-slots should comply with the relevant regulations in Chapter 2 of 3843-1999. JB/T 9957.21999 Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.