title>JB/T 4279.1-1994 General rules for verification of enameled winding wire test equipment - JB/T 4279.1-1994 - Chinese standardNet - bzxz.net
Home > JB > JB/T 4279.1-1994 General rules for verification of enameled winding wire test equipment
JB/T 4279.1-1994 General rules for verification of enameled winding wire test equipment

Basic Information

Standard ID: JB/T 4279.1-1994

Standard Name: General rules for verification of enameled winding wire test equipment

Chinese Name: 漆包绕组线试验仪器设备检定方法 总则

Standard category:Machinery Industry Standard (JB)

state:Abolished

Date of Release1994-12-09

Date of Implementation:1995-06-01

Date of Expiration:2008-07-01

standard classification number

Standard Classification Number:Electrical>>Electrical Production Equipment>>K91 Electrical Material Production Equipment

associated standards

alternative situation:Replaces JB 4279.1-1986; replaced by JB/T 4279.1-2008

Publication information

publishing house:Mechanical Industry Press

Publication date:1995-06-01

other information

drafter:Zhu Bing

Drafting unit:Shanghai Cable Research Institute of the Ministry of Machinery Industry

Focal point unit:Shanghai Cable Research Institute, Ministry of Machinery Industry

Proposing unit:Shanghai Cable Research Institute, Ministry of Machinery Industry

Publishing department:Ministry of Machinery Industry of the People's Republic of China

Introduction to standards:

This standard specifies the terminology of the verification method of enameled winding wire test equipment, the calibration of the verification equipment, and the cover style of the verification certificate and the verification result notification. This standard applies to the verification method of enameled winding wire test equipment. The verification method specified in JB/T4279.2~4279.13 is applicable to the verification of newly manufactured, repaired and in-use enameled winding wire test equipment. JB/T 4279.1-1994 General principles for verification methods of enameled winding wire test equipment JB/T4279.1-1994 Standard download decompression password: www.bzxz.net

Some standard content:

Mechanical Industry Standard of the People's Republic of China
Verification Methods of Enameled Winding Wire Test Instruments and Equipment
Subject Content and Scope of Application
JB/T4279.1·94
Replaces JB4279.186
This standard specifies the terminology of the verification methods of enameled winding wire test instruments and equipment, the calibration of the verification equipment, and the cover style of the verification certificate and the verification result notification.
This standard applies to the verification methods of enameled winding wire test instruments and equipment. The verification methods specified in JB/T4279.2~4279.13 are applicable to the verification of newly manufactured, repaired and in-use enameled winding wire test instruments and equipment.
Cited standards
GB 8170
Rules for rounding off numbers
JB/T 4279.2
JB/T 4279.3
JB/T 4279.4
JB/T4279.5
JB/T4279.6
JB/T 4279.7
JB/T4279.8
JB/T4279.9
JB/T 4279.10
JB/T 4279. 11
JB/T 4279.12
JB/T 4279.13
3 Terminology
3.1 Quick-pull speed
The maximum moving speed of the tester when there is no sample. 3.2 Space inside the box
DC resistance test device
Elongation tester
Rebound angle tester
Snap break tester
Residual tester
Electric heating forced ventilation test box
Softening breakdown tester
One-way paint scraping tester
Solvent resistance tester
Breakdown voltage tester
Low voltage paint film continuity tester
High voltage paint film continuity tester
The space defined by the inner wall of the electric heating forced ventilation test box, i.e., by the dimensions of depth, width and height. 3.3 Space temperature deviation
The temperature deviation between different positions in the box space at the same time after being adjusted at a given temperature and reaching a thermally stable state. 3.4 Temporal temperature fluctuation
After reaching a thermally stable state under a given temperature regulation, the temperature fluctuation caused by the regulator working mode at different times at the same position in the box.
3.5 Temperature deviation
Approved by the Ministry of Machinery Industry on December 9, 1994
Implementation on June 1, 1995
JB/T 4279.1-94
The temperature deviation between different positions at the same time (spatial temperature deviation) and at different times at the same position (temporal temperature fluctuation). 3.6 Working space
The space used to place the sample in the box space that meets the temperature range specified in the relevant enameled winding wire test method standards. The working space is not less than the space occupied by the sample, and its interface is parallel to the interface of the box space. 3.7 Sensitivity of defect detection circuit
The minimum current of the counter action in the defect detection circuit. 3.8 Scraping force error
After the paint film of the sample is scratched and the tester stops scraping, the relative error of the product of the load and the corresponding scraping force coefficient compared to the force value of the scraping needle actually borne by the sample. Digital rounding of measurement results
The digital rounding of measurement results shall be in accordance with the provisions of GB8170. Verification and calibration of calibration instruments
All instruments used for calibrating test instruments and equipment in this standard shall be calibrated or calibrated regularly in accordance with the regulations to ensure the accuracy of the calibration instruments.
Verification certificate and verification result notice sample standard verification certificate and verification result notice of test instruments and equipment in each part. Except for the parts already given in the verification method, they shall be in accordance with the provisions of Appendix A and Appendix B of this standard.
Equipment Name
Model Specification
Manufacturer
Factory Number
Equipment Number
Inspection Unit
Verification Result
Note: 1》Name of Verification Unit,
JB/T 4279.1--94
Appendix A
Cover Format of Verification Certificate
(Supplement)
Verification Period
Validity Period to
Equipment Name
Model Specification
Manufacturer
Factory Number
Equipment Number
Inspection Unit
Verification Result
Note: 1》Name of Verification Unit,
Additional Note:
JB/T 4279.1--94
Appendix B
Cover template of verification result notification
(Supplement)www.bzxz.net
Verification result notification
Verification period
This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery Industry. This standard was drafted by Shanghai Cable Research Institute of the Ministry of Machinery Industry and others, and the main drafter of this standard is Shui Bing.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.