This standard specifies the structure, size, PCS value and printing position of the Chinese standard book number barcode. This standard applies to books registered and published in China. GB/T 12906-2001 Chinese standard book number barcode GB/T12906-2001 Standard download decompression password: www.bzxz.net
This standard specifies the structure, size, PCS value and printing position of the Chinese standard book number barcode. This standard applies to books registered and published in China.

ICs 35,040
National Standard of the People's Republic of China
GB/T 12906—2001
Bar code for China standard hook number
Bar code for China standard hook number2001-04-09 Issued
2001-10-01 Implementation
Issued by the State Administration of Quality and Technical Supervision
GB/T12906200T
1 Scope
Referenced standards
Code structure
4 Symbol structure and binary representation
5 Technical requirements
Article 1:12906—2001
This standard is based on the International Article Numbering Association (EAVInte The FANV·TJCC:20K10 version was jointly formulated by the United States Uniform Code Committee (UCC) and the United States Uniform Code Committee (UCC). The GH/T12906-199 Chinese Standard Book Number (ISHN) part of the bar code was revised in accordance with the actual situation of my country. During the revision of the standard, 5 articles in the original standard were revised to varying degrees. The technical content in the original standard suitable for my country's situation was retained. The main contents of this standard are as follows: 1. In the book standard, only the ISTN part is retained except for the classification and type sub-part, so the name of this standard is changed to: China Standard Book Number Barcode.
2. The original standard was applicable to "books registered and published in China", and the standard after the expansion is "publications using China Standard Book Number"
3. The code structure of the original standard is a 16-digit code, and the code structure of the planner has added a form, that is, adding two digits to the 13-digit code. A total of 15 digits.
4. Added an additional The structure and technical requirements of the barcode will be introduced according to the current situation of my country's publications. The revised standard stipulates the printing position of the code to make it rigorous and convenient to use. This standard replaces (/T12905-191 from the date of implementation. This standard is reported and managed by the China Article Coding Center. The drafting unit of this standard is: China Article Coding Center. The main drafters of this standard are: Han Jiming and Xue Zhou. + Scope
National Standard of the People's Republic of China
China Standard Book Number Code
Bar Chinese standard book number GB/T12906·2001
Code G/12006—11
This standard specifies the code structure, symbology requirements and printing position of Chinese standard book special articles. This standard applies to publications using Chinese standard book numbers.
2 Cited standards
The following standards contain relevant documents, which constitute the provisions of this standard through citation in this standard. When this standard is released, the versions shown are valid, and all standards may be revised. The parties using this standard should consider the possibility of using the latest version of the following standards. GB/T05—2002 Standard Book Number
GB129041398 Commodity Barcode (neEAN General Specification>GB/T12905—2000 Barcode Evaluation
3 Code Structure
The code structure has two forms: composed of 13 digits Ning (EAN-13) composed of main code EAV13) + additional code, its structure is shown in Table 1 and Table 2:
Table 1 Code Structure 1
EAN-13
Prefix Code
3.1 Prefix Code
EAN-13
Prefix Code
X. X, X, XX, X, X, X,X
Table? Code Structure 2
EAN-13 Digital Code
X,Xy X, ×, XX,X,XgX
The check code
and||S?R is a special prefix code for the International Standard Book Number (ISKN) system designated by the International Article Numbering Association (EAVIrtoIniarul). 3.2 The digital code
is composed of a digit XX, and is a Chinese standard book number (ISBN) without a check code. 3.3 The check code
is calculated according to the method of GB12904-1998 A. 3.4 The additional code
is composed of a 2-digit digit S.6, and is used to distinguish the price changes of publications using the same standard book number. It was implemented by the State Administration of Quality Supervision, Inspection and Quarantine on April 9, 2001 and implemented on October 1, 2001. 4 Barcode symbol type and binary representation 4.1 Structure and binary representation of 13-digit barcode symbol (EAN.13 barcode>) in accordance with the relevant provisions of Chapter 1 and Section 6 of GB129011998. The Chinese standard number LHCRB is printed on the top of the barcode symbol. 4.2 Appendix barcode symbol structure and binary representation 4-2.1 Barcode symbol structure
The additional code barcode symbol consists of a start symbol. In the example, the data symbol, the middle is divided into two symbols, the right data symbol and the right blank area. The structure is as shown in Table 3.3 Additional code barcode symbol structure
Starting station, etc.
Left data format St
A sub-nest/B in the nest
China Business Division will || Note: "1" indicates a missing bar, \0\ indicates a missing block, left, right, binary data indicates A for the title or B for the ticket, according to Table 1, then the whole code is:
A thousand chloride/E dry fruit
no test area
. Module width)
When cutting the code for human recognition, select OC-B code, code business chicken and main code The bar code symbol has the same height as the bar code symbol and is vertically aligned with the upper half of the main bar code symbol. 4.2.2 Additional code characters When the additional code character is selected, the additional code bar code character set is selected according to the value of the additional code. The selection rule is shown in Table 1. Additional code bar code character selection
Additional code
4 Supplementary code printing 3109||tt ||4's abbreviation + 1, that is, 01.05,99--03
's abbreviation +=, that is, u2.0G,10--98
's integer + 3, that is, 5.011-Bg
digit: A constant D single binary representation is determined according to Chapter 6 of C12901-19B 5 Technical requirements
5.1 Technical requirements for EAN13 bar code symbols
Bar code collection
Technical requirements for FAN-11 bar code symbols according to Chapter 7 of 12994-1998: ~ Chapter 9 5.2 Technical requirements for supplementary bar code symbols
52.1 Relative placement of plus 1 bar code symbols and code bar code symbols (F4N-13 code> 5.2.1.1 The additional bar code symbol is placed on the right side of the industrial bar code number. The minimum size of the additional code symbol is: 5 modules wide, the maximum is 12 modules, and the direction is parallel to the main code symbol. 5.2.1.2 The lower edge of the additional barcode symbol is aligned with the lower edge of the main code symbol, and the lower edge of the separator and the end symbol is aligned. 5.2.2 Size of the additional code symbol
The magnification factor of the additional code symbol is the same as that of the main code symbol. The blank area on the right side of the additional code is 5 modules wide. When the
factor is 1.0, the size of the additional barcode symbol is 1. UKR-H
CB/T12906—2001
period inspection amm
Figure 1 Size of the additional code year code symbol when the magnification factor is 1 5.2.3 Other technical requirements for additional code bar code symbols mu1
Common technical requirements for additional code bar code symbols are consistent with the relevant provisions of B1290—1998, Chapter 7, 6, and the number of print positions. The preferred position for printing on the strip on the book is the cover 4 (or the lower left of the expansion door (see Figure 2. The strip of the hardcover book with non-paper cover is statically printed on the book cover. The barcode symbol is located in the upper left corner of the cover (see Figure 3) or the actual position of the book, and the direction of the barcode is parallel to the binding line. The barcode of publications and electronic publications is printed on the outer surface for easy reading. Position: 4
10m.m±4mm
The barcode is located in the lower left corner of the back cover, and the direction of the barcode is parallel to the binding line. 01bzxz.net
GB/T12906—2007
10mum±4
150-03407
The barcode is located in the upper left corner of the cover, and the direction of the barcode is parallel to the binding line.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.