title>QB/T 2480-2000 Rigid polyvinyl chloride (PVC-U) rainwater pipes and fittings for construction - QB/T 2480-2000 - Chinese standardNet - bzxz.net
Home > QB > QB/T 2480-2000 Rigid polyvinyl chloride (PVC-U) rainwater pipes and fittings for construction
QB/T 2480-2000 Rigid polyvinyl chloride (PVC-U) rainwater pipes and fittings for construction

Basic Information

Standard ID: QB/T 2480-2000

Standard Name: Rigid polyvinyl chloride (PVC-U) rainwater pipes and fittings for construction

Chinese Name: 建筑用硬聚氯乙烯(PVC-U)雨落水管材及管件

Standard category:Light Industry Standard (QB)

state:in force

Date of Release2000-06-13

Date of Implementation:2000-10-01

standard classification number

Standard Classification Number:Chemicals>>Synthetic Materials>>G33 Plastic Profiles

associated standards

Procurement status:BS 4576-1-1989 NEQ JIS A5706-1995 NEQ

Publication information

publishing house:China Light Industry Press

Publication date:2000-10-01

other information

drafter:Fu Hui, Ying Mingkang, Chen Que, Ding Kegui

Drafting unit:Shanghai Academy of Building Research, Shanghai Architectural Design Technology Development Center

Focal point unit:National Plastic Products Standardization Center

Proposing unit:Industry Management Department of State Administration of Light Industry

Publishing department:State Bureau of Light Industry

Introduction to standards:

This standard specifies the product classification, requirements, test methods, inspection rules and marking, packaging, transportation and storage of rigid polyvinyl chloride rainwater pipes and fittings. This standard applies to rigid polyvinyl chloride rainwater pipes (hereinafter referred to as "pipes") and injection-molded fittings (hereinafter referred to as "fittings") that are made of polyvinyl chloride resin as the main raw material and added with appropriate amounts of anti-aging agents and other additives. This standard applies to pipes and fittings for rainwater gravity drainage systems laid along walls and columns outdoors. QB/T 2480-2000 Rigid polyvinyl chloride (PVC-U) rainwater pipes and fittings for buildings QB/T2480-2000 Standard download decompression password: www.bzxz.net

Some standard content:

Classification number G33
Preparation number 7309—2000
Light Industry Standard of the People's Republic of China
QB/T 2480—2000
Rigid polyvinyl chloride (PVC-U) for construction
Rainwater pipes and fittingswww.bzxz.net
2000-06-13 Issued
State Bureau of Light Industry Issued
2000-10-01 Implementation
8/T2480—2000
Full standard Non-equivalent British user standard BS4576 from 1:1-1989 Rigid polyvinyl chloride rainwater pipes and fittings Part: Graphic and shaped section rainwater pipes? And formulated in combination with national conditions. The standard adopts the specifications of tensile strength, fracture length, linear shrinkage, Vicat drop hammer impact test in this standard: This standard only applies to temporary pipe fittings with cross-section, which has a small scope. According to the production and use of my country, the products with cross-section are added: The weather resistance test refers to the accelerated aging test of JISAS706-99S hard polyurethane water-soluble polyurethane. The aging time of this standard is 500h, and this standard is set as 100h. The test method of the national standard is consistent with the current test method standard of China, so all the relevant requirements are in accordance with the national standard of my country. Appendix A in the technical standard is the additional requirements of the standard.
This standard is issued by the National Light Industry Bureau of China and is under the jurisdiction of the National Plastic Products Standardization Center. The originating unit of this standard: Shanghai Institute of Architectural Science and Technology, Shanghai Architectural Design and Technology Development Center. The participating entities of this bid are: Sunjian Yadao Rubber Co., Ltd. and Shenzhen Huaihua Baosi Plastic Co., Ltd. The drafters of this standard are: Bo Ji, Ying Qiukang, Chen E, and Ke Cheng. Scope
Light Industry Standard of the People's Republic of China
Rigid Polyethylene for Construction (PVC-IUJ)
Rainwater Pipes and Fittings
B/T2480—2000
This standard specifies the product classification, requirements, test methods, inspection regulations and marking, packaging, transportation and storage of polyurethane rainwater pipes and fittings.
This standard is applicable to extruded water pipes (hereinafter referred to as "pipes") and injection molded fittings (hereinafter referred to as "pipes") made of polyurethane as the main raw material and with a certain amount of anti-aging and other additives. This standard is applicable to pipes and fittings for gravity drainage systems designed for outdoor use and production. 2 Cited standards
The following standards contain provisions that become provisions of this standard through reference in this standard: When this standard is issued, all new minor versions are valid: All new standards will be revised. Parties using this standard should explore the possibility of using the most recent existing versions of the following standards:
GB250-195 Evaluation of color change companion card
Month/T2828-19 Note? Batch control box counting and slapping procedures and sample forms are applicable to the inspection of continuous batches) GB/T2918-199B Standard environment for the state and harmony test of plastic specimens GB6671.1-1986 Test method for the longitudinal reel rate of rigid polyvinyl chloride (PVC) materials GB/T8802-1988 Test method for the Vicat softening temperature of rigid fluoroethylene (PVC-L) pipe fittings GBT880-1 Injection molding rigid fluoroethylene (PVC-J) pipe fittings: oven test method GB/T8804.1-1988 Test method for tensile properties of thermoplastic plastic pipes Polyvinyl chloride materials GB/T8805-198B Test method for the curvature ratio of rigid pipes GB/T8806-1 9889
Method for measuring the skin size of plastic awnings
Method for testing the light source noise exposure of plastics
GR/T9344-19882
GB/T14152-1993
3 Product classification
Test method for the external impact resistance of thermoplastic plastic pipes and tubes--Real-time impact method 3.1 Products are divided into the following two categories:
A) Square pipes and tubes:
B) Circular pipes and tubes,
4 Specifications and dimensions
4.1 Rectangular pipes and tubes
The specifications and dimensions of rectangular pipes and tubes shall comply with the provisions of Figure 1 and Table 1. The external dimensions of other sections may be determined by both supply and demand. The parties agree: State Light Industry Bureau 2000-06-13 approved
2000-10-01 implementation
63×42
75×50
:10x73
125×83
16X[07
110×3
125×94
160×120
or this and the difference
4.2 Inductive pipe material
GB/2480-2000
Over-shaped pipe tree dimensions and wall sequence
Rectangular pipe specifications and deviations
Approximate radius||tt ||Basic size
Rectangular pipe material shall comply with the provisions of Figure 2 and Table 2. The nominal outer diameter of the rectangular pipe and the nominal outer diameter of the pipe fittings.
Q/T2460:2000
Table 2 Specifications and deviations of rectangular pipes
Allowable deviation
125.0 No. 4
4.3.1 Basic size
The specifications and sizes of the sockets and spigots of rectangular pipe fittings shall comply with the provisions of Figure 3 and Table 1.
Figure 3 Rectangular pipe fittings, printing, insertion and lifting
Table 3 Rectangular pipe bearings, spigots and sequence.
Original size and deviation
63×42
110×73
150×H02
110x83
125×94
160×12n
116 center
Basic and deviation
Basic size4
Thickness of body
Adjustment section
Note: The test degree and service intention of the manufacturer are determined by 3
+0.4%--0.2%
Teflon semi-light
4.32 Round fittings socket
AB/12480-2000
The specifications and dimensions of the socket and spigot of the example pipe fittings shall comply with the provisions of Medicine: 4 and Table 4. O
National shape first door, extract and start
Table 4 medical shape pipe fittings socket, Pu mouth and wall
Winter called external protection
The basic size and difference of the socket, the thickness of the socket and the balance difference
.103.474
1: The strength of the socket and the size of the contract are determined by the manufacturer. 4.4 Rectangular pipe fittings
The size of rectangular pipe fittings shall comply with the provisions of Figure A1 to Figure A3 and Table A1-Table A3, see Appendix 4.4.5 Rigid joints
The size of mesh pipe fittings shall comply with the provisions of Figure A4-Figure A6 and Table 44-Table A6, see Appendix A5 requirements
5.1 Pipe
5. t.1 Rattan sheet,
The color of the pipe is white.
5.1.2 Appearance
The inside and outside of the pipe should be smooth and flat, and the gloss should not drop. The discoloration line and other defects should not be visible on the surface of the pipe. The surface of the pipe should be cut out smoothly and perpendicular to the axis. 5.1.3 Curvature
The curvature of the pipe should not be greater than 1.0%.
5.1.4 Dimensional deviation
The size and deviation of the pipe should comply with the provisions of Table 1 + Table 4. 5.1.5 Physical and mechanical properties
Q/T 2480—2000
The physical and mechanical properties of the pipe should comply with the provisions of Table 5. Table 5 Mechanical properties of pipes
Tensile strength MPa
Tensile shrinkage %
Vicat softening degree,
Drop impact test 2m
5. 2 Fittings
Tensile surface retention %
Color
A method: TTR-1%
Month method, 12 times of washing, 12 times without cracks
The color of the fittings is white. The color of the pipe should be consistent with the color of the pipe. 5.2.2 External
The internal and external surfaces of the fittings should be smooth, no bubbles, peeling and severe cold spots are allowed, obvious marks and texture are not leaking, etc.:
5.2.3 Dimensional deviation
The length and texture of the pipe should comply with the provisions of Appendix A. 5.2.4 Physical and mechanical properties
The physical and mechanical properties of the fittings shall comply with the requirements of Table 6. Table 6 Physical and mechanical properties of pipes
6 Test method
Heat treatment liquid
Baking resistance test
6.1 Test pretreatment
New GB 8803 Chapter G
Unless otherwise specified: According to GB2918, the state of the sample is tested at (23 ± 2) ° C for 24 hours: .2 Color and appearance
The color and appearance of the pipe and fittings are checked offline. 6.3 Specification dimensions and deviations
.3.17 Average outer diameter and thickness
Pipes and fittings are measured according to GB/TBBG6. .3.2 Thickness and thickness
General materials and pipe properties When measuring round pipes, measure eight points on the pipe in one section. When measuring round pipes, measure two points on each side and take the maximum and minimum values. 5
6.3.3 New port
OB, T 2480-2000
Technical Figure 3 and Figure 4 The parts of the specification are measured with a vernier ruler with a precision width of 0.02m, and the maximum value and the minimum value are determined. 6.4 Pipe
6.4.1 The bending
Technical GB/T8805 shall be used for determination: The bending degree of the rectangular pipe shall be measured by its face and B mountain, and the increased value shall be taken as the bending degree. 6.4.2 Tensile strength and gradual elongation
shall be determined according to GB/T8804.1: The sample is taken from the A of the rectangular pipe. 6.4.3 Numerical shrinkage
shall be determined according to the B method in GB/16671. The test temperature is (120±2)°C, and the test piece is 30mm in diameter. The two straight lines and the two sides of the B-shaped tube sample are evenly drawn, and the pad does not touch the bottom of the oven. After the test, take the maximum value of each sample, and then take the average value of the samples as the test result. 6.44 Softening temperature of plastic film shall be measured according to B8802. 4.5 Drop induced burst test shall be carried out according to GB14152, test temperature is 20+1℃ water bath, impact weight is 2.0kg, punch height is 200mm, impact head diameter is 25mm, the shaped tube is placed on a 12V shaped bracket, the short shaped tube is placed on a half board and fixed, the distance between the inner fulcrum is the specimen length minus 20mm, the super-shaped tube is punched out of the middle part of each surface, A method is used to judge the result according to GB14152, B method is used for factory inspection, 12 sections are tested, 12 impacts should not break the plastic for 12 times, A method is used for the intermediate test. 6.4.6 Weathering test According to GR9344, the test time is 1000h, the test period is 18min/102mn (wetness interval/wetness time), the blackboard temperature is (63±3)°C, the relative humidity is (65±5)%, 6.4.6.1 Tensile elasticity retention rate According to the test method in 6.4.2, the cumulative calculation formula is (%) - P 100.. Or: 6
Tensile strength, MPa: P--tensile elongation after curing, MPa. 9.4.6.2 Color change According to GB250, the evaluation shall be carried out.
6.5 Pipe fittings
6.5.1 Softening temperature
Determined according to GB/T8802.
6.5.2 Oven test
Determined according to GB/T8803:
7 Rules
QB/T 2480—2000
.1 Products can only leave the factory after being inspected and qualified by the quality inspection department of the manufacturer and accompanied by a certificate of conformity. . . 2 Inspection classification
Inspection is divided into two categories: inspection and type inspection: T. 2. 1 Factory inspection
Mountain! The inspection items are the external measurement, specification size, curvature, longitudinal shrinkage and chain drop impact test of the pipe. Method B: The external measurement, specification size and baking test of the pipe. 7.2.2 Single type inspection
During normal production, the inspection is carried out once a year: weather resistance test is carried out once every three years. When there are special requirements, the type inspection of this standard should also be carried out. 1) When the new product is tested and identified
b) After formal production, the structure, raw materials and process will have minor changes, which may affect the performance of the product: 2) When the product is stopped for more than two months, when the production is resumed, the inspection results are different from the last type inspection: 3) When the quality supervision regulations require the type control inspection. 1.3 Batching and sampling
7.3.1 Batching
A batch of products produced in reverse with the same raw material formula, process, variety and specification. The quantity of each batch of pipes shall not exceed 1, and the number of pipe fittings shall not exceed 5,000. The minimum batch size can be a batch of products with a production period of 10 days.
7.3.2 Bundle sampling
7.3. 2. 1 Strict inspection
The inspection of package size, specifications and tolerances shall be carried out in accordance with the regulations of GB/T2828, with a normal sampling plan: take 1 section for inspection, and the qualified standard is AQL6.5, see Table 7. 12 sections are taken for inspection, and the number of samples is (pieces). The sampling plan and judgment range of batch are shown. 151--280 281500 5011200 120 [--3209 3201~1IO 7. 3. 2. 2 Type inspection Sample is too small\
Qualified products are listed as A. In the output! Sufficient products are randomly selected from the qualified products for type inspection: 4 judgment rules and multiple inspection rules are given. (pieces) The judgment is invalid. Appearance, size and curvature are judged according to the provisions of 7. When one item of physical performance fails to meet the specified standard, a double sample can be randomly selected from the sample household for re-inspection. If there is any unqualified, the batch is judged as unqualified.
White marking, packaging, transportation, storage
8.1 Marking
Japanese. 1.1 Pipe
Pipe materials should have the following permanent markings:
Company) Product name:
Trademark:
Specification type:
d Manufacturer's name:
9) Production period and batch number:
f) Standard number adopted
6. 1.2 Product
QB/T 24802000
8.1.2.1 The following permanent marks should be on the pipe fittings: Product name or trademark: b) Specification model. B.1.2.2 The outer packaging of the pipe fittings should be marked: a) Product name: b) Manufacturer's name and address. 0) Trademark: 1) Specification model: 2) Export standard number: 3) Production date or batch number. 8.2 Packaging: Pipes are generally made of plastic. Pipe fittings are generally packed in line. Other packaging forms are agreed upon by both parties: 8.3 Transportation: During transportation, the product shall not be subjected to strong impact, throwing and heavy pressure. 8.4 Storage: The storage area of ​​the product must be flat and the stacking should be neat. The height should not exceed 100%. 5m, torch heat source 1 or more, when the pile falls, it must be stimulated to prevent soil from lifting wine.
The storage period is generally not more than 18 months from the date of production. Nominal specification
53×42
110×73
125×3
160×107
110×83
160120
8/2480-2000
Time record A
【Appendix】
Dimensions of pipe fittings
Figure A1 Rectangular pipe 135° elbow
A1 Short pipe 135° pipe grid
Tower size
67.6×46.6
80.0×55.0
i15.8 x78.4
132.6×90.6
169.0×116.0
116.t X89.1
169.U29.0
58.63x.37.6
70.2×45.2
1U4.6X57.6
118.0×76.0
151.6×.98.6
1C-4.0×77.0
HR.nXRZ.G
151.6x111.6
Nominal specification
63×42
75x 50
10×73
125×83
160107
125xy4
160X120
OB/T2480—2000
Figure A2 Shaped pipe outlet
Table A2 Specifications of Shaped pipe outlet 11
Basic dimensions
676×46.6
80.0X55.0
13 5.8×78.4
1326×90.6
167.心×116.心
116.4XB9.4
1326x101.6
169 .0[29.0
25×50
[25×R3
160×.107
110x83
125×94
16n×12n
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.