Mechanical Industry Standard of the People's Republic of China JB/T58651.1~58651.14—1999 JB/T58652—1999 Quality classification of fastener products (Internal use) Published on December 3, 1999 National Machinery Industry Implementation on June 1, 2000 1 Scope Mechanical Industry Standard of the People's Republic of China Quality classification of fastener products Nuts (Internal use) JB/T 58651,4-1999 5865144 This standard specifies the principles and requirements for the quality classification of parent products produced in accordance with national standards and industry standards. Other standards can be used for reference in the classification of the quality of products produced by the same industry. This standard adopts three-level classification, namely superior products, first-class products, and qualified products. This standard is applicable to the batch of single-specification products received according to GB9. All the sizes used in this standard are consistent with the current nut standards. Reference standards The provisions contained in the following standards have become the provisions of the standards through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision. Offices using this standard should explore the possibility of using the latest versions of the following standards: GBT901985 GR.T 214.2--1996Www.bzxZ.net GB.T 309R.2—1982 (confirmed in 1988) GB.T3098.4—-1986 GB.T3098.6—1986 GD.T 3934—1983 GBT $7792—1986 JB/T 87K8—1998 JB58651.1—1999 3Nouns, terms and calculation formulas Fastener acceptance inspection, marking and packaging Pu standard calipers Vernier calipers Fastener mechanical properties nuts Slotted nut Fastener mechanical properties Fastener mechanical properties Fastener mechanical properties Stainless steel nuts, nut factories, ethylene nuts General frequency efficiency specifications|| tt||Prohibited parts surface defects World…Requirements General rules for fastener product quality classification Defect grade, sensitivity, such as investment value and unit potential, the principle of the standard and the unit defect grade. The formula for the first 511 regulations A, spot check items, sampling plan, fast defect grade and supervision of nut products, sampling plan, defect grade and weighted value are as specified in the table, 5 grade standards Nut product quality standards are as specified in Table 2. 6 Inspection methods Nut product inspection hall is as specified in Table 3, approved by the State Machinery Industry Bureau on December 34, 1999 2 (HH0-06-01 implementation In the project Against the edge width 3 Negative width JBT 586S1.4—1999 Butterfly pattern specification [Mean diameter and diameter of thread] Burning specification [Single medium and light] Burning specification [Mixed products] Screw pit diameter High pressure m Opening width Partial opening seat Support surface diameter area Edition treatment accuracy m And carry the symmetry of the thread axis Flatness of the nut support surface and the coal effective axis Type II surface defect -Natural table But the lack of danger Key performance Non-destructive inspection Carbon reduction control Quality city Compatible products First-class products Superior products Qualified products · Products Fake products Suppress the brightness Fill in UB/I3098.2 or GB/T3098.4 or GB/T3098.6 fixed A Single lack of standard pool 0.133 Fst.335 0. 169 F 0.424 Oil Li said day width on side 5 width on diagonal depth this common now! Screw effect making medium and large diameter! flame thread stop gauge (single diameter of screw thread ; miscellaneous products scorpion minor diameter, nut height lower dragon degree% support H amount d flange point d vibration control high waste m opening the thread axis to the degree thread axis weight a type of surface age depression a fire installation and missing Kai pregnancy servant JB /TS8651.4—1999 (21 special inspection boundary 2! Special inspection products through special plug effect stop screw wave rate gauge smooth case gauge 12) special caliper gauge non-standard, now squeezed GB/T1214.2 GB:T1214.2 GB/T3934 (design scale should be included in the report, the range is still within the measurement, in the treatment of high quality from the beginning to the maximum, the room gauge should be able to pass the teacher (excluding the effective short part of the lock screw, GB3934 GS/T 3934 GHT12142 :1) Caliper R 2 Time gauge () Caliper (21 Special caliper -with screw bar, vertical gauge GB/T1214.2 GBT1214.2 GBT1214.2 GB/T52142 GH/T 1214.2 3BT8788 Use your hand to remove the visible part of the mold at both ends of the customer gauge, and the sea is not completely clear. (Control back and hope to see the juice! , for the small Ding 3 this period of small, also can not be fully suitable for the grass and the test and the important letter the mother's texture, the composition benefit through the plan, does not include the A sales quality screw responsible for the effective force of the public: : stop the production of the current dismantling of the media at both ends of the machine effect in line with the view to let (1 month 2 type mother two need to be Z+2, 0.5m.. (2 net 50.8 code: Z,+Z,*0.65mm 【3) the cumulative thickness and the file system from the support The bracket t at one end of the surface: 2e=0.350 【4】The sum of the two dimensions of the explosion: 2+,53”First measure the approximate starting point and the integral point, and then measure the distance between the inner points Put the cross-shaped nut into the special thread, and the impact should be eliminated: parallel hole According to GB/T.5779.2 According to GL/T3098.2 or GD/T3098.4 or GL30986, now with 23 Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.