This standard specifies the terminology, type and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of cartridge pressure filters. This standard applies to cartridge pressure filters. JB/T 8866-2001 Cartridge pressure filter JB/T8866-2001 Standard download decompression password: www.bzxz.net

1CS21.010
Machinery Industry Standard of the People's Republic of China
JB/T8866-2001
Simple Pressure Filter
Cartridge filter
Published on 2001-05-23
China Machinery Industry Federation
Implemented on 2001-10-01
JB/T 8866-2881
This standard is a revision of JB 8866-1999 (ZBJ77005-1989) simple pressure filter. The technical content has not changed after the revision, and the mark of filter cloth type filter element has been added. This standard replaces JB/T 866-1999 from the date of implementation. This standard is proposed and managed by the National Separator Standard Promotion and Equipment Technical Committee. The responsible units for drafting this standard are: Hefei General Machinery Research Institute, Qingdao Gas Cutting Machine Sugar Factory, Tonglu Filter Factory. The drafters of this standard are: Wen Zhengxian, Xu Hongwang, Xu Fuzhi. This standard was first issued in March 1989 as 2BJ77005-1989, and the standard number was adjusted to JB8866-1999 in April 1999. This is the first time to subscribe.
1 Scope
Machinery Industry Standard of the People's Republic of China
Simple Pressure Filter
Cartridge filter
J/T8866—2001
Chemical Rong B 8866—1999
This standard specifies the terms, types and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of simple pressure filter.
This standard is applicable to simple pressure filter
2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are all valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards: GR 191—1990
GB/T 4334.1—2000
GB.T16951961
GB/T 9867—1988
GB/T 1701—1982wwW.bzxz.Net
GB/T2100—1980
GB/T2649—1989
GB/T2651—1989
GB/T 2653—1989
GB/T 7780—1987.
GBT:10894—1989
GB/T13306—1991
GB/T133B4—1992
GR.T 9439—1988
JB/T7217—1994
3 Terminology
3.1 Pre-pressure filter
Packaging, storage and transportation pictorial symbols
Test method for 10% grass energy diffusion of stainless steel
Determination of dielectric strength and withstand voltage of vulcanized rubber at power frequency Determination of abrasion properties of rubber by the sheet method
Determination of tensile strength and elongation at break of rubber cavity Technical conditions for stainless acid-resistant steel castings
Welding Joint mechanical performance test sampling method welding joint tensile test method
Welding joint Liqu and main fan test method
Filter model comprehensive method
High mechanical noise sound power level measurement engineering method sign
General technical conditions for packaging of electromechanical products
Gray iron parts
General technical conditions for coating of external separation machine
The filter equipment with filter element as filter element installed in the round container is called Jianwu pressure filter. 3.2 Filter element change to standard filter element pass area
The porous filter element of the shape is called filter element, and the filter element with inner diameter of -29mr and length L=250m is defined as standard filter element. The nominal filter area of ​​the standard filter element has nothing to do with the type of filter element, nor with the actual filter area, and its value is set to 0.3m. Approved by China Machinery Industry Federation on May 23, 2001, and implemented on October 1, 2001#
Types and basic parameters of cartridge pressure filter 4. [Simplified type of filter element is shown in Figure 1 Filter element
JE/T8866-200E
Pressure gauge
4.2 Model compilation of cartridge pressure filter 5 According to the provisions of 0B7780, the expression method is as follows. Filtration area, m
Filter element type code
Filter element type code is shown in Table 1.
Seal type
Sand winding type
Marking example:
Edit top type
Making gift plastic
Circular carbon type
Gold high-burning sticky type
Combustion picture
Golden silk weaving
Nominal filter area! .2m\ Yarn winding type cylinder type such as H through the German machine, marked as: TYR1.24.3 Shang type filter basic parameters according to Table 2. Combustion cloth type
Nominal filter area
5 Technical requirements
JB/T8866—2001
Long standard filter element
Four commercial inner diameters
Number of cores in the mother layer ()
Mixed core products
5.! Simple pressure filter should meet the requirements of this standard and be manufactured according to the samples and technical documents approved by the prescribed procedures. 5.2 The materials and external parts selected for simple pressure filter should have the supplier's certificate of conformity. When there are no qualified products, they can only be used after being inspected and qualified by the manufacturer:
5.3 When simple pressure filter is used for filtering beverages and pharmaceuticals, the selected material composition shall comply with the relevant provisions of the Food Hygiene Law. 5.4 The manufacture and acceptance of non-inductive acid-resistant wires must comply with the provisions of GH2100. 5.5 The welding of joints must be welded with welding rods that are equivalent to or better than the parent material. The mechanical properties of the welded specimens shall be tested in accordance with the provisions of GB/T2619, GB/T2651, GB/T2653, and GB/T2652. Cast steel welding chains shall be treated to prevent intergranular corrosion, and the intergranular corrosion tendency test shall comply with the provisions of GB4334.1 as required.
5.6 The simple filter press shall not have any leakage at the sealing of each part and component under 1.25 times the rated working pressure. That is, after the pressure is zero, the parts shall not have obvious deformation and damage. 5.7 For the cartridge pressure filter equipped with the specified number of standard cores, under the positive difference of 0.03MPa, the flow rate of 25±57 water must reach the frequency value.
5.a The acoustic level of the filter overflow noise made by the cylinder shall not exceed B4B (A5.9 The electrical and control equipment shall be complete, waterproof, and have good operation and maintenance, and shall be equipped with a grounding device. 5.1 In the commercial filter, the surface of the exposed non-anti-rust materials and components of the filter shall be sprayed with anti-rust paint. The spraying method and quantity shall be in accordance with the provisions of JBT7217.
6 Test methods and inspection rules
JB/TB866-2001
6. Commercial pressure filter mechanical strength and sealing test Close the outlet valve of the simple pressure filter, and without installing the filter element, pressurize the water into the filter tube body with a simple pressure filter, and conduct a water test at 1.25 times the rated working pressure, and maintain the pressure for 10min , check the sealing conditions, and check the deformation and damage of each pressurized part and component after pressure relief. The pressure gauge has a precision of grade 1, and the selected pressure decay should make the test pressure value more than one-tenth of the full scale of the pressure gauge.
6.2 Determination of water flow
According to the provisions of 5.8. The continuous measurement time is not less than 30min. There are two measurement methods: volumetric method and flow meter method: 8 Reduction meter method: When measuring the water flow, the liquid entering the flowmeter should be kept constant. The flowmeter must be calibrated in time, and the relative error is not more than 1.5%
b) Volumetric method (measure the time required to process a volume of water in a container) When measuring water flow, the container should be calibrated in advance and marked with scale, and its relative error is not more than 1.5%. .3 Measurement of noise
The noise of the simple pressure filter shall be in accordance with the provisions of Appendix E in GB/T10894. 64 The inspection of rubber plate lining of parts and components of simple pressure filter shall be carried out in accordance with the provisions of 0B/T1695, 0B/T9867 and GB/T1701. 6 Simple pressure filter factory inspection and type inspection 6.5.1 Each simple pressure filter shall be inspected in accordance with the requirements of 5.6, 5.7, 5.10 and 5.11. Only qualified pieces can be shipped to the factory.
6.5.2 In addition to the contents specified in 6.5.1, the contents of type inspection shall also be in accordance with 5.5, 5.8 and 5.9. Type inspection should be carried out in any of the following cases: a) Trial type identification of new products or old products for transfer to factory production; b) After the production is stopped, if there are major changes in structure, materials, and technology, which may affect product performance; c) During normal production, it should be carried out once a year; d) When the product is stopped for a long time for more than 1 year and production is resumed; e) When there is a big difference between the factory inspection result and the last type inspection result; f) When the national quality supervision agency puts forward a request for type inspection. Labeling, packaging, transportation and storage
7.1 Each simple pressure filter should be equipped with a label in a conspicuous place. Its type and size should comply with the provisions of GBT13306. The content of the label includes:
) Model and name of the filter
b) Main technical parameters
Nominal filtration area: m*
Type of filter element;
Number of standard filter elements: pieces;
Rated working force: MPa
Allowable height gain: %:
Motor power: kw;
Total machine weight: kg:
Overall dimensions (length×width×height): mm:) Factory number:
) Manufacturing date:
e) Manufacturer name.
JB/T8966—2001
T.2 The packaging of the simple filter press shall comply with the provisions of GB/T133. 3 The packaging box marking shall comply with the provisions of GB191. 2.4 The random documents shall be packaged directly and fixed in a conspicuous position in the box: The random documents shall include: a) Packing list; b) Product certificate; c) Production manual (including instructions for use of main accessories); d) List of spare parts accessories.
7.5 The cartridge pressure filter shall be stored in a place with relative humidity not exceeding B0%, temperature between 540°C and with a safe environment. Quality assurance period:
If the user complies with the use and preservation conditions, within one year from the date of the manufacturer's purchase, if the product is damaged or cannot run normally due to poor manufacturing, the manufacturer shall be responsible for replacing it for the user.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.