This standard specifies the definition, type, basic parameters, requirements, test methods, inspection rules, marking and packaging of peak inductive micrometers. This standard applies to peak inductive micrometers (hereinafter referred to as micrometers) with a pointer indicating a graduation value of 0.1, 0.2, 0.5, 1, 2, 5, 10, 20 μm. JB/T 8787-1998 Peak inductive micrometer JB/T8787-1998 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T 8787:1998
Peak Sensing Micrometer
Published on July 17, 1998
National Bureau of Machinery Industry
Implementation on December 1, 1998
JR/T8787-1998
Compared with JB/GQ5C29, this standard adds Chapter 7 "Inspection Regulations". This standard is proposed and managed by the National Technical Committee for Instrument Standardization. The responsible person for drafting this standard is Zhongyuan Automation Institute. The main drafters of this standard are: Di Baoyu. Dai Wenhua, Fan
Standard of the Machinery Industry of the People's Republic of China
Peak Inductive Micrometer
JH/T8787-1996
This standard defines the specifications, types, requirements, test methods, inspection rules, marking and packaging of peak inductive micrometers. This standard is applicable to the reduced inductive micrometer (hereinafter referred to as F) with a scale value of 0.1.020, 1.23, 10, 20r indicated by finger F.
2 Referenced Standards
The following references are used to indicate the meaning of the reference in the standard. The original version of this standard is valid for all versions. All non-standard parts can be found by using the latest version of the above standards. [2142-0 Inductive micro-transmitterWww.bzxZ.net
3 Definition
This instrument can be defined as follows.
3, the inductive micro-position sensor can be used to convert the change of the measured value into a signal, and can also be used as a measuring instrument to compare the measured value, the minimum value, the maximum and minimum values, the maximum and minimum values, the average value, etc. 3.2 Vertical value stability
In these memories, when the measurement is taken, the maximum change of the indicated value is calculated from the time when the measurement is taken. 4 Types and basic parameters of the indicator and sensor are used for measurement. The technical system diagram is for reference only. Test lamp
Tongfu return
Wepingguan
Quantity increase and development
National Machinery Industry Corporation approved on July 17, 1998 and implemented on July 17, 198120
JH,T 8787-1998
4.2 Sensor type and installation shall comply with the provisions of 2B.42042-9-hole 4.2. 4.3 Graduation value shall comply with the provisions of (unit,) 0.1.c.2, 0.5.1, 2, 5.10, 20.
4.4 The scale interval shall not be less than 1mml
5 Requirements
5.1 Appearance
The surface shall not have rust, industry and coating shedding defects. Each mark and mark shall be straight and clear. 5.2 All fastening parts should be flexible, all rotating parts should be flexible, and there should be no jamming or movement. 5.3 Insulation and positive resistance At dc500V, the resistance between the two ends of the series connection socket and the shell should be no less than 5MA. At ae1000V, the positive test indicator should not have any wear phenomenon. 5.4 Response time The response time should not be greater than 1 minute. 5.5 The zero adjustment time should be less than 20 seconds. 5.6 The zero position of the balance should not be greater than one point of the minimum scale interval. 5.7 Indication variability
The indication variability of each gear shall not exceed one third of the 10-phase sequence gear value. 5.8 Direction error
The direction error shall not be greater than the provisions of Table 1,
Graduation surface
5. The return error
The same direction error shall not exceed the provisions of Table 2.
5.10 Indication error
The indication error shall not be greater than the provisions of Table 8
Direction error
1 division value
1/2 division value
-/3 division value
-73 external variable
Function code
Price
5. 11.1 Stability of indication JB/T8787-1998 The maximum and minimum values ​​of the measuring range should not exceed the value specified in Table 4. Within the working range specified in Table 4, the stability of the measuring range should not exceed 2000W/4000W. Within the working range specified in Table 4, the stability of the measuring range should not exceed 2000W/4000W. Within the working range specified in Table 4, the stability of the measuring range should not exceed 2000W/4000W. 11. 3. Stability of operation
In each value column, the stability of the measuring instrument should be greater than 1 scale value/5 times. 5.2. Signal indication variability
In each value column, the indication change of the signal trigger point should not be greater than 1 scale value/5 times. 5.1. The influence of power supply voltage change on the indication voltage should be within the specified range of 9%-110%. When the voltage changes, the change of indication caused should be within 1.2 scale values. 5.1.1.1 The design value of the sensor pressure measurement should not be greater than 1.N for shaft type and not greater than 0.15N for support type. 5.4.2 The measuring force should be within 80%-20% of the actual value. 5.1. 5. Materials, surface finish and surface finish. The measuring instrument should be made of good quality materials. The test product hardness should not be less than 766HV, and the surface roughness should not be less than R, U5. 6.1.1 The test environment should be 76.1℃ and the temperature change should not exceed 0.3℃. 6.1.2 The test site should be free of vibration and strong magnetic field. 6.1.3 The potential measuring instrument and the measuring table should be kept at 13℃. The measuring instrument should be preheated for 15min after being powered on. The above test method should be adjusted as follows: 6. 1. 4H source is a, c. F0 IT3 or 6a TTz, 22) V. 6.2 Test items E, test methods Test items within the test method, test method and see Table 5. Student number
Appearance and
Super mutual maintenance
"dry"
Response time
Position balance
Interactivity
Difference between
and company complaint
Return loss
Indication error
Light into
Stability is the skin
Compensation determination
Visual inspection, feel
JB/I87871998
Use the first edge of the heart medical design to add power to the continent. The power source is not transmitted to the continent and the machine is drawn! Network value, and then under the 10o gram low voltage sample of 501 or 60x, on the "degree", make the sexy limit quantity on the workbench contact with each other, and then give the sensor the same value of one-tenth of the indication range of the figure as the time on the indicator report || tt || in the "stand", make the sensor and the workbench quantity on the life of the volume adjustment adjustment from the system to the ratio end, reverse out of the back station move range pressure in the "stand", the element in the small guard benefit value block this pair of military engraving finally move each gear in turn to the zero position of the programming switch now share each quiet when the zero position of the volume can be adjusted to the corresponding scale on the workbench instrument; pay attention to the case scale! Use the lifting mechanism to gently lift the probe, and then let it fall freely. The lifting amount should be greater than the indication range of the ten gears, and the lifting amount should be consistent. Repeat 1C times, take the maximum and minimum indications of each time, and make them consistent with the normal determination on the platform. Record the scale line on the two pointers. When the measuring head is on the measuring head, align the left and right four probes with the three probes, and use the force equivalent to 2C of the material design force to make the sensor fall! The amount on the workpiece is relative, and the sensor is slowly moved to a certain extent. After the measurement is accurate, lift the probe gently again. The lifting amount should be greater than the indication range of the ten gears, and then gently put it down again. Find the value of the pointer after the rise, collect the average value, and align it with the indicator.The wave line is again plated with symptoms. The set of measurements of the instrument stand workbench is determined according to the corresponding method. The measurement of the index of the batch is the same as the first batch of the file. The zero scale is negative, and the full dose tablet line is then divided into four equal parts (or six equal parts) according to the low range of the display. The corresponding amount is changed in total, and the values ​​of these sensory types are checked in turn on the file. The three straight lines of the film are the smallest points. The two god faces of the special forget the well stand are connected to each other! Let the adjacent degree line of the Shangyu line overlap, and the film can be determined at the time of starting: the most change of the straight salt || tt| |In, after completing a gear, the range will be expanded and the minimum division value will be adjusted. The device will also adjust the loss needle separately. During the time, take the change in the value of the loss lamp that is lit within the reverse time. At the valley end, when the memory position is half of the small division value or half of the gear... or one of the whole, the meter will be placed under the measurement ratio and protection ~ original, and the specified time will be indicated by the large value of the north
. Please use the specified time as the signal indication hall
voltage change
for the indication
JB/T 87871996
Table 5 (end)
Test monitoring
In ""When theft, the quality process is the minimum, the actual trust is in the position, turn the adjustment code, so that the indicator light is evenly rotated, so that the indicator light is lit in the special danger plan, the total water is correct, and the sequence is heavy! Take 15 times the change of the signal light's indication value according to the previous month
In a gear, make the sensor and the case Work to accept orders, half make the pointer overlap with the full distance money, : education crying input -L5DH, 22V special power in the rhyme light straight + 10% of the energy change, read the maximum change of the wine run: the sensor installed on the platform to measure the vertical self-mouth, and then use the dynamometer to move the sensor along the tail of the station tide. Inspection rules 7.1 Factory inspection |The probe is slowly increased in force, and the pointer passes the test number on the dynamometer when it is raised. Then the probe is slowly moved downward, and the pointer passes the test number on the dynamometer. The dynamometer must pass the quality inspection of the manufacturer before it can leave the factory. The factory inspection items should include the contents of 5.1 to 5.14. Inspection quantity 100
7.2 Judgment rules
All inspection items should be filed, and the product should be marked as β mark and packaging
8. The label of the small exposure should be marked:
a) manufacturer's name or registered trademark;
b) product name and model;
) product serial number:
:13 years;
c) power supply voltage.
8.2 The sensor should be marked:
a) manufacturer's name or registered trademark
e) sensor model;
product number1
d year of manufacture.
8.3 The product packaging should have good anti-rust, anti-rust and other measures. The outer packaging should have the product name, manufacturer's name or registered trademark and "upward", "sandwich" and "shockproof" signs. 4 The following documents should be attached with the product: b) Product certificate of conformity, the certificate of conformity should have the standard code and product serial number; c) Double packing list.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.