Some standard content:
JCS 07.060.67.263
Marine Industry Standard of the People's Republic of China
1IY/T 067—2002
Fiber reinforced plastic tanks for water treatment
Fiber reinforced plastic tanks used in water treatment mcnt2002-12-3D Issued
State Oceanic Administration Issued
2003-02-01 Implementation
HY/T06/—20C2
This standard is not a series of core. When establishing the external pressure and being killed, it refers to the indicators of similar products produced by the bacterial removal process. Appendix A of this general standard is the appendix of the special standard. Appendix, for the request (fire reminder of the record. This standard is issued by the National Marine Standard Center of the People's Republic of China. The main initiators of this standard are: Harbin Lepu Industrial Development Center, Tianjin Membrane Engineering Technology Co., Ltd., Harbin Lepu Industrial Development Center, responsible for the interpretation of this standard. 1 Scope
Marine Industry Standard of the People's Republic of China
Fiber reinforced plastic for water treatment
Fiber reinforced plaslie lanka msed in aler Ircalmeal [Y/T 067—2002
This standard specifies the characteristics, raw materials, technical requirements, test methods and inspection rules of the steel used in the process. This standard applies to glass substrates and their products as the base material, unsaturated nitrile or vinyl resin as the base material and the base type of water treatment glass. 2 Reference standards
The texts included in the following standards are incorporated into this standard by reference. When this standard is published, the version shown is valid. All standards The standard will be revised, so all parties who promote the use of the following standards should explore the latest quality of wood: 55-year pulping resin content test method GB/T28251987 Gram-by-gravure counting sample sequence and sampling table (with + sequence for continued batch picking) GR/T3854—1983 Fiber-reinforced plastic medical package strength test method Fiber-reinforced thermosetting plastic tape water pressure peak effect pressure test method GB/TE351198 G,T 823-1?R7
Glass fiberglass reinforced plastics, glass fiber ... |Approved by the State Oceanic Administration on December 30, 2002
Male part form
Seat form
Inner height protection
Inner diameter
Code
2053-02-01 implementation
EY/T067-2032
4.2.1FRT is the simplified form of glass fiber reinforced plastic box for water treatment (iani:nforedplastLar.kensetin wnrriHiim) written in English.
The inner diameter of the key refers to the equal inner diameter of the component. The requirements are shown in Table 2. Other sizes can be agreed upon by both parties. Table 1
Inner diameter of common glass fiber reinforced plastic ends for water treatment
The inner height is the height of the component. The requirements are shown in Table 2. The average size is determined by negotiation between the supply and demand parties: Table 2
Inner height dimensions of common glass fiber reinforced plastic ends for water treatment
Inner height size
Maximum size:
2 1:1:
13161373
The average size refers to the inner diameter of the component. The requirements are also shown in Table 3. Other sizes are determined by negotiation between the supply and demand parties. 4.2.4
Table 3 Water treatment pipe size
Outlet mm
4.2.5 Substrate type,
B---Standard base;
In length.
4.2.6 Overall type:
F:
7. Overall type
4.2.7 Marking example:
For example, RPT core ××T"F indicates that the water treatment pipe is used. The inner diameter of the pipe is mm. The inner diameter of the pipe is mm, and the inner diameter of the pipe is 3.5 mm. 5 Raw materials
5.1 Base material
5.1.1 The base material is not as specified in GBT3237. 5.1.2 For the above materials, the vinyl resin shall not be lower than the standard T3/T7. 5.2 Elastic materials
5.2.1 There shall be no red group with the core of C277. 5.2.2 The glass fiber yarn, spunbond and rubber cloth shall have a lubricant that matches the corresponding resin. 5.2.3 Organic fiber surface felt or other materials may be used. 2
6 Requirements
6.1 Surface requirements
HY/T 067—2002
The outer surface of the steel plate shall be flat and smooth. There shall be no defects such as cracks, irregularities and obvious bubbles. There shall be no peeling of the composite material.
6.2 Size requirements
6.2.1 The size of the joints at the beginning and the end shall be marked as shown in Figure 1. 1. Diameter of the whole - inner diameter 2. Diameter of the whole - inner diameter 3. Height of the whole body 4. Diameter of the whole - inner diameter 5. Height of the whole body 6.2.2 Dimensional tolerance 6.2.2.1 Dimensional tolerance 6.2.2.1 Dimensional tolerance 6.2.2.1 Dimensional tolerance 6.2.2.1 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6.2.2.2 Dimensional tolerance 6. -17-00
shunt public mT
.r -:+s?
HY/T057—2002
group high this is the public
7E2 i:1 32J
: 521 +#L, 4.3 286
6.2.2.4 fuel body high make external treatment public signature see support? . error note (old thickness) point meet the requirements of 6.7. Table? end work allowance evaluation public some
yuan range pressure: mm
allow will n
Ye2::[522
5.2.2.5 embedded standard effect no public to low through the standard medium load observation of the equipment test. 6.2.3 The requirements for the actual tolerance of the nodes are as follows: 8, 524286
The table changes the line when the practice of the public voucher
pressure/nn
6.3 The average fat insoluble content
7t2 $L-.1 324
1 52:.L -22 285
The root of BT357 is tested: the resin insoluble content (quality is greater than or equal to 8). 6.4 The surface of the body is the right to use the degree of ten 35.6.51 The minimum pressure of the big
is greater than or equal to 0, MP:. 6. Water is positively connected to the punching energy
2 2365:Lt
Test with 1.0=M1. water pressure at normal temperature, guarantee point 1)min~30mn, the opening of the screen should not have water 6.? Water pressure dry plate pressure
After the test at room temperature with 3.6MP water pressure, the end body does not affect the use requirements: 5.8 Sanitary performance
Can meet (1115 Section
6.9 Purchase parts
Other parts including stores and complex villages are attached with the "Appendix to the Supply".? Test method
Night surface test
Day measurement of the surface of the same time.
The investment, outer diameter, production, overall height and some vertical line dimensions of the bull are shown in accordance with the research record 4 (Standard Appendix!) :7.3 Resin cannot contain chromium
Car grease cannot contain liquid ... 8 According to the inspection rules, the inspection is a type of inspection.
8.1 Factory side inspection
8.1. Inspection items
Factory dial inspection is carried out according to 6.1..2.2.2, 3.2.1, 6.2., G.1, 6. requirements 8. 1.2:
Min only inspection:
8.1.3 Rules
a) Walking surface, lower inch, world hardness, water pressure test are 15. The product is qualified, otherwise it is qualified when the fire is qualified b) The surface will not be allowed to be repaired, six rely more than twice: one in the "inner process inch such as times the side thickness < for the product near the Asian style inspection value, the course method see the appendix) the public wasteland of the scope of use. The plan is for the fall. Li Liu is not qualified for the body height change No. internal height small bottom thickness ( For the purpose of the recent type inspection, any method can be recorded in the public welfare and the scope of use, the agent is the standard and the plan is not in dispute. 8.2 Single inspection release
8.2.1 The test strip is one of the following situations: a) the material combination of the general product is slipped, ". When the process has obvious changes, which may affect the performance: h) stop normal mass production 2 plan:
stop production for 6 months 1 change the effective production work:
mountain) mountain! There are big differences in the type of inspection: the import quality monitoring machine requires the import type inspection, 8.2.2 Inspection on the report 6th provisions for inspection 8.2.3 Samples of goods B.2.2.1 The same series of support rods can be produced by the cattle to the 5th batch 8.2.3.2 BT2828 period, the joint batch method. Take the orange water section, AQ[.8.2.4 HY/T 067-?C02 8) When all indicators meet the requirements of Chapter 5, the type inspection is judged to be qualified, otherwise the type inspection does not include bridges. ) The qualified batch is determined in accordance with G/T228. 9.1 Labeling
All the outer surfaces of the product should be marked with durable information. The marking should include the following: a) Nominal inner diameter and inner height; b) Product identification:
) Manufacturer name, trademark, manufacturer number and original standard number; 9.2 Packaging
The product should be packed in a suitable way to prevent scratches; 9.3 Transportation
During transportation and loading, the product should not be subjected to severe pressure or damage; 9.4 Storage
The product should be stored in a safe place and should not be exposed to disasters and strong heat sources. A1 Measurement of external characteristics (D)
A1.1 Instrument
HY/T C67—2002
(Standard
Dimension measurement method
Vernier caliper: Graduation value 3.02mm: 10mm: Graduation value 1A1.2 Graduation
41.2.1 When the diameter (D) is equal to or greater than 2C3mT, select one surface at the top, middle and bottom of the tube section and measure it with a vernier ruler. The measuring points are all
412,2 When the outer diameter (D) is greater than 20mm: select one surface at the top, middle and bottom of the tube section, and use a rotating ruler to set the length of each surface around the member.
41. 3 Calculation
41.3.1 Grid (less than 8m inches, calculate the average. 41.3.2 Grid (> greater than 2us1nm) T./x calculate the average. 41.4 Average,
A2 Measurement of height (L)
A2.1 Instrument
.3m sample ruler: Graduation value 1mm: Width angle ruler. A2.2 Method
Make a vertical position, place the width ruler close to the ground, close to the chain, and use the adjustment ruler to measure the length from the ground to the width angle ruler, as shown in Figure A. Distribute the number of points evenly according to the angle. Schematic diagram of high flow measurement plate
A2.3 Sieve
Calculate the average.
A3 Measurement of the straightness of the busbar
A3.1 Instrument
HY/T067—2002
Graduation: Graduation value 0.c2mn; mechanical half ruler. A3.2 Method
Select the equally divided busbar, and tighten the flat ruler along the busbar. In the whole measurement, measure the width of the chain with the ruler, and then measure the selected busbar.
A3.3 Count the sections
Calculate the average value.
A4 Measurement of the inner diameter (d>
A4.1 Instrument
Graduation value of the vernier F ruler.2mm.
A4.2 Method
Select one horizontal war on the upper, lower and lower sections of the straight line and use a vernier caliper to measure the inner diameter of each section. A4. 3 Calculate the half mean. A5 Cut the wall thickness d, and then cut the wall again. A5.1 Instrument Vernier caliper: Graduation value center m 15.2 Method A5.2.1 Method of continent 4 Select the following: On the straight line segment of the front body, select the following: separate the sections, and use the vernier caliper to measure the wall thickness center on each surface. Total: 100 measurement points are evenly distributed. A5.2.2 Method of measuring d As shown in Figure A2, the front body is cut into two parts by the line, and the caliper is used to measure the wall thickness. Create a straight line in the two parts? Second: points are evenly distributed:
Figure 2, schematic diagram of the query point
A5.3 Calculate the average value of the sum,
A6 Measurement of internal height (Z,)
A6.1 Instrument
[om old ruler: value 1mm:
A6.2 Method
IY/T 067-2002
As shown in Figure A2, the query point axis is divided into two parts with the open chain body, and the internal height 1 is measured with a difference ruler. Give the inner height value
Inner diameter×inner height:
152×330
152×457
152×813
152×889
18×G73
16×669
17H×1016
1781-18
203×432
272×7H2
203564
29:X414
2 57×1:18
229×1315
229×1213
234253
AXI01G
254119
254×1194
354X372
Narrow volume:
HY/T067—2002
Appendix B
(Extremely detailed appendix)
Recommended classification size table
Inner diameter of the mouth:
E:1, 5
305×737
305×384
305x1 21
319×12
356×1 372
35G×551
406×584
406×#36bZxz.net
406113||t t||406:x1072
4:5X1e51
457:.1651
457 *1 905
568-1651
5×1905
6101551
B13x1965
813×2556
1 217,
Shikou Trail!
$3. 5,Jo1.6,1.4. 2
53. 5,101.6,3-J.3
63. 5,101. 6,1.4. 2
6+.5,Jo1.6,1.4.3
6..?.1t.t.1!.3
63, 6 .:01.6,1.-.3
63, 5,101.6,1-4.3
63, 5,101. 6,1-4. 3
6.5.101.6,1:1.3
$3. 2,JOI.5,IJ3
$3.5, 161. 5,2:J. 2
sw.s.dot.e.lik.3
65.101.E.11.3
67, 5,101, 6,111.3
5,161, 6,1 4, 3
63. 5,1c1, 5,1-4, 3
151. 6.114. 3
151.6.114.3
tut. G.111.3| |tt||5L. E, I1-t.3
Jut. t.llt.3
Jul. t.11t.3
Jui.e...3| |tt||131.5.114.3
131. 5,114. 3
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.